A force vector F1−→F1→ points due east and has a magnitude of 130 newtons. A second force F2−→F2→ is added to F1−→F1→. The resultant of the two vectors has a magnitude of 390 newtons and points along the (a) east/ (b) west line. Find the magnitude and direction of F2−→F2→. Note that there are two answers.
(a) Below are choices (a) due south, due east, due north, due west Number ________ newtons
(b) due west, due south, due east, due north Number ____________ newtons

The problem involves a radio station broadcasting at a frequency of 92.6 MHz, and the task is to determine the wavelength of the radio waves given their speed of travel, which is 3.00 x 10^8 m/s.

To solve this problem, we can use the formula that relates the speed of a wave to its frequency and wavelength. The key parameters involved are frequency, wavelength, and speed.

The formula is: speed = frequency * wavelength. Rearranging the formula, we get: wavelength = speed / frequency. By substituting the given values of the speed (3.00 x 10^8 m/s) and the frequency (92.6 MHz, which is equivalent to 92.6 x 10^6 Hz), we can calculate the wavelength of the radio waves.

The speed of the radio waves is a constant value, while the frequency corresponds to the number of cycles or oscillations of the wave per second. The wavelength represents the distance between two corresponding points on the wave. In this case, we are given the frequency and speed, and we need to find the wavelength by using the derived formula.

Learn more about Frequency:

https://brainly.com/question/29739263

#SPJ11

The combined resistance in the circuit is 776 Ω and the current flowing in the circuit is 77.3 mA.

Given: Three resistors are connected in series. The resistors are 56 Ω, 220 Ω, and 500 Ω. The total voltage in the circuit is 60 V.  

To find: The combined resistance in the circuit and the current flowing in the circuit.  

As the resistors are connected in series, the total resistance (R) can be found by adding the individual resistances.

R = R1 + R2 + R3R

= 56 Ω + 220 Ω + 500 ΩR

= 776 Ω

The combined resistance in the circuit is 776 Ω.

The voltage in the circuit is 60 V.

Using Ohm's Law, the current (I) flowing through the circuit can be found.

I = V / RI = 60 V / 776 ΩI = 0.0773 A (approximately)

The current flowing in the circuit is 77.3 mA (rounded to two decimal places).

When resistors are connected in series, the total resistance is equal to the sum of the individual resistances. Ohm's Law is used to calculate the current flowing in the circuit.

Learn more about Ohm's Law: https://brainly.com/question/1247379

#SPJ11

The description to the diagram and the concepts are as given below. The final angular speed of the disc-brick system is 235.8 rad/s. The kinetic energy of the system must increase to maintain the law of conservation of energy.

a) The description of the vector diagram for the angular momentum before and after placing the brick on the disc.

Before placing the brick on the disc:

The vector diagram for the angular momentum of the spinning disc consists of a vector representing the angular momentum, which is directed along the axis of rotation and has a magnitude given by the product of the moment of inertia and the angular speed. The magnitude of the vector is proportional to the length of the vector arrow.

After placing the brick on the disc:

After placing the brick on the edge of the disc, the angular momentum vector diagram will show an additional vector representing the angular momentum of the brick.

This vector will have a magnitude determined by the product of the moment of inertia of the brick and its angular speed. The direction of the vector will be the same as that of the disc's angular momentum vector.

b) The physics laws and concepts used to find the angular speed of the dise-brick system are the law of conservation of angular momentum, the moment of inertia, and the law of conservation of energy. The law of conservation of angular momentum states that angular momentum is conserved in a system in the absence of an external torque.

The moment of inertia of a rigid object depends on the distribution of mass in the object, relative to the axis of rotation. The moment of inertia for a solid disc is (1/2)MR².

The law of conservation of energy states that the energy of a system remains constant unless it is acted upon by a non-conservative force. In this case, the only non-conservative force acting on the system is the friction between the brick and the disc.

c) The initial angular momentum of the disc is given by:

L1 = Iω1

where I is the moment of inertia of the disc and ω1 is the initial angular speed of the disc.

L1 = (1/2)MR12ω1 = (1/2)(100)(1.6)²(25) = 4000 kg m²/s

The final angular momentum of the disc-brick system is:L2 = Iω2where ω2 is the final angular speed of the disc-brick system. The moment of inertia of the disc-brick system can be calculated as:I = (1/2)MR12 + MR22 = (1/2)(100)(1.6)² + (20)(1.6)² = 425.6 kg m²/sThe final angular momentum of the disc-brick system is:

L2 = Iω2L2 = (425.6)(ω2)

The law of conservation of angular momentum can be used to find the final angular speed of the disc-brick system.

L1 = L2Iω1 = (425.6)(ω2)ω2 = ω1I/I2ω2 = (25)(4000)/(425.6) = 235.8 rad/s

d) The kinetic energy of the system increases when the brick is placed on the disc. This is because the moment of inertia of the system increases, while the angular speed remains constant.

Therefore, the kinetic energy of the system must increase to maintain the law of conservation of energy.

Learn more about energy at: https://brainly.com/question/2003548

#SPJ11

Answer: Jupiter > Neptune > Venus > Mars

Explanation: edmentum

between 1.7 kg.m2.0 to 2.1 and the density of this 2D shape is uniform with the value of 4.5 kg/m

Given that the line is rotated about the y-axis, to calculate the moment about the y-axis, we need to use the axis of rotation formula, which is given as,

Mx = ∫ ∫ x ρ dx d y

The mass is calculated using the formula,

m = ∫ ∫ ρ dx d y

We can find the y-coordinate of the center of mass of the plate using the formula,

My = ∫ ∫ y ρ dx d y

Now to calculate the center of mass of the 3D volume created by rotating the same lines about the y-axis and assuming the density is uniform with the value of 3.1 kg/m, we can use the formula ,

M z = ∫ ∫ z ρ dx d y d z

The mass is given as,

m = ∫ ∫ ρ dx d y d z

To calculate the z-coordinate of the center of mass of the 3D volume, we use the formula,

M z = ∫ ∫ z ρ dx d y d z

Let us calculate the quantities asked one by one: Mass of 2D shape: mass,

m = ∫ ∫ ρ dx d y

A = ∫ 0+1.1 ∫ 1.7+2.1 y d y dx∫ ∫ y d

A = ∫ 0+1.1 yd y ∫ 1.7+2.1 dx∫ ∫ y d

A = 0.55 × 2.8 × 4.5= 6.615 kg

To know more about density visit:

https://brainly.com/question/29775886

#SPJ11

The man can stand at a maximum distance of 6.53 m from the axis of rotation without sliding.

The man can stand on a merry-go-round rotating at 3.0 rad/s without sliding if the coefficient of static friction between the man's shoes and the merry-go-round is μs = 0.6.

Now, we need to find the maximum distance the man can stand from the axis of rotation without sliding. Let us consider the following diagram: [tex]A[/tex] is the man standing on the merry-go-round rotating at 3.0 rad/s, and [tex]F_{friction}[/tex] is the static frictional force that opposes the relative motion of the man on the rotating merry-go-round.

According to the question, the coefficient of static friction between the man's shoes and the merry-go-round is [tex]\mu_s = 0.6[/tex]. The formula for the static frictional force is [tex]F_{friction} \leq \mu_s F_{normal}[/tex].

where [tex]F_{normal}[/tex] is the normal force. Since the merry-go-round is rotating, there is a centripetal force that acts on the man, which is given by [tex]F_c = mr\omega^2[/tex].

where m is the mass of the man, [tex]\omega[/tex] is the angular velocity of the merry-go-round, and r is the distance of the man from the axis of rotation.

Hence, the normal force acting on the man is given by [tex]F_{normal} = mg[/tex].where g is the acceleration due to gravity. Therefore, [tex]F_{friction} \leq \mu_s F_{normal}[/tex][tex]\implies F_{friction} \leq \mu_s mg[/tex][tex]\implies mr\omega^2 \leq \mu_s mg[/tex][tex]\implies r \leq \frac{\mu_s g}{\omega^2}[/tex]Plugging in the given values, we get: [tex]r \leq \frac{(0.6)(9.8)}{(3.0)^2}[/tex]

Simplifying, we get: [tex]r \leq 6.53 m[/tex].Therefore, the man can stand at a maximum distance of 6.53 m from the axis of rotation without sliding.

To know more about  axis of rotation  refer here:

https://brainly.com/question/31439072#

#SPJ11

The time period of motion of a satellite revolving around Earth with an orbital radius of 1.5 x 10^4 km is 67805.45 seconds

The time period of a satellite revolving around Earth with an orbital radius of 1.5 x 10^4 km can be calculated as follows: Given values are:

Mass of Earth (M) = 5.97 x 10^24 kg

Radius of Earth (R) = 6.38 x 10^3 km

Newton's Gravitational Constant (G) = 6.67 x 10^-11 N m^2/kg^2

Mass of the Satellite (m) = 1050 kg

Formula used for finding the time period is

T= 2π√(r^3/GM) where r is the radius of the orbit and M is the mass of the Earth

T= 2π√((1.5 x 10^4 + 6.38 x 10^3)^3/(6.67 x 10^-11 x 5.97 x 10^24))T = 2π x 10800.75T = 67805.45 seconds

The time period of motion of the satellite is 67805.45 seconds.

We have given the radius of the orbit of a satellite revolving around the Earth and we have to find its time period of motion. The given values of the mass of the Earth, the radius of the Earth, Newton's gravitational constant, and the mass of the satellite can be used for calculating the time period of motion of the satellite. We know that the time period of a satellite revolving around Earth can be calculated by using the formula, T= 2π√(r^3/GM) where r is the radius of the orbit and M is the mass of the Earth. Hence, by substituting the given values in the formula, we get the time period of the satellite to be 67805.45 seconds.

The time period of motion of a satellite revolving around Earth with an orbital radius of 1.5 x 10^4 km is 67805.45 seconds.

To know more about Gravitational Constant visit

brainly.com/question/17239197

#SPJ11

The mechanisms of the rotary kiln combustion process are including ignition, Flame Propagation , Flame Quenching,Drying of Fuel Particles and heat transfer.

Ignition: Initially, fuel combustion begins with the ignition. Combustion of any fuel will need a temperature increase until it achieves its ignition temperature, which is about 200 °C.

Flame Propagation: The ignition leads to the next step, which is flame propagation. Once the combustion process begins, the flame starts moving ahead and spreading through the fuel particles. It is possible through the emission of heat in the backward direction from the flames to the fuel and the release of energy from the fuel. The combustion products like CO2 and H2O (carbon dioxide and water) are emitted during the flame propagation stage.

Flame Quenching: The third step is the flame quenching. In this step, the fuel combustion process slows down, and the flame stops moving through the particles. It happens when the supply of oxygen and fuel becomes less due to less flow rates.

Drying of Fuel Particles: The fuel particles need to dry before ignition and combustion. The process of drying happens due to the heat transfer from the combustion gases to the fuel particles.

Heat Transfer: Heat transfer is a crucial process for fuel combustion. It refers to the exchange of heat energy between hot combustion gases and fuel particles. The heat transfer mechanism between gas and particle includes conduction, convection, and radiation.

Learn more about flaming combustion at

https://brainly.com/question/14104327

#SPJ11

I agree with the HR Manager's decision to give Mahmood another chance. While it is true that he has been given a warning and is not very productive in his work.

His lame leg makes it difficult for him to get to work on time, and he has an extended family that depends on him financially. His colleagues are willing to cover for him, which shows that he is a valuable member of the team.

I believe that it is important for employers to be understanding and flexible when it comes to employees' personal circumstances. If Mahmood is able to address the issues that are affecting his performance, he has the potential to be a valuable asset to the company.

Here are some additional thoughts on the matter:

It is important for employers to have clear policies and procedures in place regarding attendance and productivity. These policies should be fair and consistent, and they should be communicated to employees in advance.

Employers should be willing to work with employees who are struggling to meet expectations. This may involve providing accommodations, such as flexible work hours or job modifications.

Employers should also be mindful of the impact that their policies and procedures can have on employees' mental and physical health.

In Mahmood's case, the HR Manager could have taken the following steps:

Talk to Mahmood about his personal circumstances and how they are affecting his work.

Explore options for accommodating Mahmood, such as flexible work hours or job modifications.

Provide Mahmood with resources to help him manage his time and productivity.

Monitor Mahmood's progress and provide additional support as needed.

By taking these steps, the HR Manager could have helped Mahmood to address the issues that were affecting his performance and to become a more productive employee.

To learn more about HR Manager click here

brainly.com/question/30613164#

#SPJ11

When the particle achieves the maximum positive y-coordinate, it is at a distance of 0 meters from the origin. This means it is still at the origin in the xy plane, as its x-coordinate remains zero throughout its motion.

The distance of the particle from the origin when it achieves the maximum positive y-coordinate, we need to analyze its motion in the xy plane.

Initial velocity, u = 5.2 i m/s

Acceleration, a = (-5.4 i + 1.6 j) m/s²

We can integrate the acceleration to find the velocity components as a function of time:

v_x = ∫(-5.4) dt = -5.4t + c₁

v_y = ∫1.6 dt = 1.6t + c₂

Applying the initial condition at t = 0, we have:

v_x(0) = 5.2 i m/s = c₁

v_y(0) = 0 j m/s = c₂

Therefore, the velocity components become:

v_x = -5.4t + 5.2 i m/s

v_y = 1.6t j m/s

Next, we integrate the velocity components to find the position as a function of time:

x = ∫(-5.4t + 5.2) dt = (-2.7t² + 5.2t + c₃) i

y = ∫1.6t dt = (0.8t² + c₄) j

Applying the initial condition at t = 0, we have:

x(0) = 0 i m = c₃

y(0) = 0 j m = c₄

Therefore, the position components become:

x = (-2.7t² + 5.2t) i m

y = (0.8t²) j m

To find the maximum positive y-coordinate, we set y = 0.8t² = 0. The time when y = 0 is t = 0.

Plugging this value of t into the x-component equation, we have:

x = (-2.7(0)² + 5.2(0)) i = 0 i m

Therefore, at the time when the particle achieves the maximum positive y-coordinate, it is at a distance of 0 meters from the origin.

Learn more about ” velocity ” here:

brainly.com/question/30559316

#SPJ11

The mass of the lead is 44 grams.

Let’s denote the mass of the lead as m. The heat gained by the ice, water the mass of the lead is approximately 44 grams

and copper cup is equal to the heat lost by the lead. We can write this as an equation:

m * 128 J/kg°C * (96°C - 12°C) = (3.33 * 10^5 J/kg * 0.038 kg) + (0.038 kg * 4.186 J/kg°C * (12°C - 0°C)) + (0.220 kg * 4.186 J/kg°C * (12°C - 0°C)) + (0.100 kg * 387 J/kg°C * (12°C - 0°C))

Solving for m, we get m ≈ 0.044 kg, or 44 grams.

And hence, we find that the mass of the lead is 44 grams

Learn more about ice

https://brainly.com/question/14045710

#SPJ11

To calculate the rotation speed of the ruler+clay system after the collision, we need to first determine the center of mass of the system and then calculate the moment of inertia about this center of mass.

Center of Mass of the Ruler+Clay System:

The center of mass (COM) of the ruler+clay system can be calculated using the following formula:

COM = (m1 * r1 + m2 * r2) / (m1 + m2)

Where:

m1 is the mass of the ruler

m2 is the mass of the clay

r1 is the distance from the ruler's original center of mass to the system's center of mass (unknown)

r2 is the distance from the clay to the system's center of mass (unknown)

Since the ruler is initially at rest, the center of mass of the ruler before the collision is at its midpoint, which is L/2 = 1.0 m / 2 = 0.5 m.

The clay is thrown toward the ruler, and after sticking, the system's center of mass will shift to a new location. Let's assume the clay sticks at the end of the ruler furthest from its initial center of mass. Therefore, the distance from the ruler's original center of mass to the system's center of mass (r1) is 0.5 m.

Now we can calculate the center of mass of the system:

COM = (0.401 kg * 0.5 m + 0.401 kg * 1.0 m) / (0.401 kg + 0.401 kg)

COM = 0.75 m

So the center of mass of the ruler+clay system is at a distance of 0.75 m from the ruler's initial center of mass.

Moment of Inertia of the Ruler+Clay System:

The moment of inertia (I_COM) of the ruler+clay system about its center of mass can be calculated using the parallel axis theorem:

I_COM = I + m * d^2

Where:

I is the moment of inertia of the ruler about its own center of mass (given as 12 ML^2)

m is the total mass of the system (m1 + m2 = 0.401 kg + 0.401 kg = 0.802 kg)

d is the distance between the ruler's center of mass and the system's center of mass (0.75 m)

Let's calculate the moment of inertia about the system's center of mass:

I_COM = 12 * 0.401 kg * 1.0 m^2 + 0.802 kg * (0.75 m)^2

I_COM = 12 * 0.401 kg * 1.0 m^2 + 0.802 kg * 0.5625 m^2

I_COM = 4.828 kg m^2 + 0.4518 kg m^2

I_COM = 5.28 kg m^2

So the moment of inertia of the ruler+clay system about its center of mass is 5.28 kg m^2.

Calculation of Rotation Speed:

To find the rotation speed of the ruler+clay system after the collision, we can use the principle of conservation of angular momentum. The initial angular momentum (L_initial) of the system is zero because the ruler is initially at rest.

L_initial = 0

After the collision, the clay sticks to the ruler, and the system starts to rotate. The final angular momentum (L_final) can be calculated using the formula:

L_final = I_COM * ω

Where:

ω is the rotation speed (unknown

To know more about inertia click this link -

brainly.com/question/3268780

#SPJ11

Power transferred = 12 kW. Volume of liquid in the tank = 250 litres = 250 kg. Specific heat capacity of the liquid = 2.45 kJ/kgK. Taking the density of the liquid as 0.789 kg/litre, we have:Mass of liquid in the tank = volume × density = 250 × 0.789 = 197.25 kg. We need to calculate the temperature increase in the liquid after 5 minutes. We can use the following formula to do so:Q = m × Cp × ΔT Where:Q = Heat energy transferred into the liquidm = Mass of the liquid. Cp = Specific heat capacity of the liquidΔT = Change in temperature of the liquid.

Rearranging the formula, we get:ΔT = Q / (m × Cp)We know that Q is the power transferred into the liquid for 5 minutes. Power is the rate at which energy is transferred. Thus: Power = Energy / Time Energy transferred into the liquid for 5 minutes = Power transferred × time = 12 kW × 5 × 60 s = 3600 kJ. Thus,ΔT = 3600 / (197.25 × 2.45) = 7.25 K. Therefore, the temperature of the liquid will increase by 7.25 K after 5 minutes, assuming there is no heat loss from the tank.

Learn more about temperature:

brainly.com/question/27944554

#SPJ11

A. The work done by gravity is calculated using the formula W_gravity = mgh, where m is the mass, g is the acceleration due to gravity, and h is the height.

A. To calculate the work done by gravity, we can use the formula W_gravity = mgh, where m is the mass of the object (10.0 kg), g is the acceleration due to gravity (9.8 m/s²), and h is the height through which the object is lowered (2.20 m).B. The work done by the tension in the rope can be calculated using the same formula as the work done by gravity, W_tension = mgh. However, in this case, the tension force is acting in the opposite direction to the displacement.

C. The net work on the system is the sum of the work done by gravity and the work done by the tension in the rope. We can calculate it by adding the values obtained in parts A and B.

The final kinetic energy can be calculated using the formula KE = (1/2)mv^2, where m is the mass of the object and v is its final velocity (0.80 m/s). The net work done is then equal to the difference in kinetic energy, which can be calculated as the final kinetic energy minus the initial kinetic energy.

To learn more about work done by gravity, Click here:

https://brainly.com/question/16865591

#SPJ11

Therefore, the solutions to the simultaneous equations are approximately: T = 65 and a = 2.79

To solve the simultaneous equations 98 - T = 10aT - 49 = 5a, we can use the method of substitution.

Step 1: Solve one equation for one variable in terms of the other variable. Let's solve the first equation for T:
98 - T = 10aT
Rearrange the equation by moving T to the left side:
T + 10aT = 98
Combine like terms:
(1 + 10a)T = 98
Divide both sides by (1 + 10a):
T = 98 / (1 + 10a)

Step 2:
Replace T with 98 / (1 + 10a) in the second equation:
5a = 98 / (1 + 10a) - 49

Step 3: Solve the equation for a.

5a(1 + 10a) = 98 - 49(1 + 10a)
Expand and simplify:
5a + 50a^2 = 98 - 49 - 490a
Combine like terms:
50a^2 + 5a + 490a - 49 - 98 = 0
50a^2 + 495a - 147 = 0

Step 4: Since the quadratic equation does not factorize easily, we will use the quadratic formula:
[tex]a = (-b ± √(b^2 - 4ac)) / 2a[/tex]
For our equation 50a^2 + 495a - 147 = 0, a = -495, b = 495, and c = -147.
Substitute these values into the quadratic formula:
[tex]a = (-495 ± √(495^2 - 4 * 50 * -147)) / (2 * 50)[/tex]

Calculating the values inside the square root:
[tex]√(495^2 - 4 * 50 * -147)[/tex]

= [tex]√(245025 + 29400)[/tex]

= [tex]√(274425) ≈ 523.9[/tex]

Simplifying the quadratic formula:
[tex]a = (-495 ± 523.9) / 100[/tex]
This gives us two possible values for a:
a = (-495 + 523.9) / 100 [tex]≈ 2.79[/tex]
a = (-495 - 523.9) / 100 [tex]≈ -10.19[/tex]

Step 5:
Using the equation T = 98 / (1 + 10a):

For a = 2.79:
T = 98 / (1 + 10 * 2.79) [tex]≈ 65[/tex]

For a = -10.19:
T = 98 / (1 + 10 * -10.19) [tex]≈ -58.6[/tex]

To know more about square root visit:

https://brainly.com/question/29286039

#SPJ11

Ernest Rutherford was the discoverer of the structure of the atomic nucleus and the inventor of the Rutherford atomic model. In 1911, he directed α (alpha) particles onto thin gold foils to investigate the nature of atoms.

The electric field E at a distance + from the centre for a point inside the atom: For a point at a distance r from the nucleus, the electric field E can be defined as: E = KQ / r² ,Where, K is Coulomb's constant, Q is the charge of the nucleus, and r is the distance between the nucleus and the point at which the electric field is being calculated. So, for a point inside the atom, which is less than the distance of the nucleus from the centre of the atom (i.e., R), we can calculate the electric field as follows: E = K Ze / r².

Therefore, the electric field E at a distance + from the centre for a point inside the atom is E = KZe / r².

Let's learn more about Rutherford atomic model:

https://brainly.com/question/30087408

#SPJ11

Birefringence is defined as the difference between the refractive indices of the extraordinary and ordinary rays in a birefringent material. Birefringence (Δn) = ne - no. The thickness of the sheet ice required for a quarter-wave plate, assuming it is illuminated by light with a wavelength of 600 nm at normal incidence, is approximately 393.3 nm.

Δn = 1.313 - 1.309

Δn = 0.004

Therefore, the birefringence of the ice crystal is 0.004.

ii. To calculate the thickness of the sheet ice required for a quarter-wave plate, we can use the formula:

Thickness = (λ / 4) * (no + ne)

where λ is the wavelength of light and no and ne are the refractive indices of the ordinary and extraordinary rays, respectively.

Plugging in the values:

Thickness = (600 nm / 4) * (1.309 + 1.313)

Thickness = 150 nm * 2.622

Thickness = 393.3 nm

Therefore, the thickness of the sheet ice required for a quarter-wave plate, assuming it is illuminated by light with a wavelength of 600 nm at normal incidence, is approximately 393.3 nm.

To learn more about, Birefringence, click here, https://brainly.com/question/31961152

#SPJ11

In an AC circuit, the voltage and current vary sinusoidally over time. The peak voltage (Vp) refers to the maximum value reached by the voltage waveform.

The RMS voltage (Vrms) is obtained by dividing the peak voltage by the square root of 2 (Vrms = Vp/√2). This value represents the equivalent DC voltage that would deliver the same amount of power in a resistive circuit.

Vrms = 120/√2, resulting in Vrms = 84.85 V.

P = Vrms^2/R, where P represents the average power and R is the resistance.

Plugging in the values, we have P = (84.85)^2 / 10, which simplifies to P = 720 W.

Therefore, the average power dissipated in the resistor is 720 watts. This value indicates the rate at which energy is converted to heat in the resistor.

It's worth noting that the average power dissipated can also be calculated using the formula P = (Vrms * Irms) * cosφ, where Irms is the RMS current and cosφ is the power factor.

However, in this scenario, the given information only includes the peak voltage and the resistance, making the first method more appropriate for calculation.

Overall, the average power dissipated in the resistor is a crucial factor to consider when analyzing AC circuits, as it determines the energy consumption and heat generation in the circuit component.

know more about Voltage here : brainly.com/question/29867409

#SPJ11

The magnitude of the sum of the

momenta

can be found using the vector addition of the individual momenta.

The direction of the sum of the momenta can be described as an angle with respect to due east.

(a) To find the

magnitude

of the sum of the momenta, we need to add the individual momenta vectorially.

Momentum of the first jogger (J1):

Magnitude = Mass ×

Velocity

= 76 kg × 3.2 m/s = 243.2 kg·m/s

Momentum of the second jogger (J2):

Magnitude =

Mass

× Velocity = 67 kg × 2.7 m/s = 180.9 kg·m/s

Sum of the momenta (J1 + J2):

Magnitude = 243.2 kg·m/s + 180.9 kg·m/s = 424.1 kg·m/s

Therefore, the magnitude of the sum of the momenta is 424.1 kg·m/s.

(b) To find the direction of the sum of the momenta, we can use

trigonometry

to determine the angle with respect to due east.

Given that the second jogger is heading 56° north of east, we can subtract this angle from 90° to find the direction angle with respect to due east.

Direction angle = 90° - 56° = 34°

Therefore, the direction of the sum of the momenta is 34° with respect to due east.

To learn more about

momenta

click here.

brainly.com/question/32847939

#SPJ11

This can be proven by changing the time scale in the equation of motion for the second ion.M(d²r/dt²) = q(E + v × B)  this expression can be used.

Bleakney's theorem states that if a nonrelativistic ion of mass M and initial velocity zero moves along a trajectory in given electric and magnetic fields E and B, then an ion of mass kM and the same charge will follow the same trajectory in electric and magnetic fields E/k and B.

To understand the proof, let's consider the equation of motion for a charged particle in electric and magnetic fields:

M(d²r/dt²) = q(E + v × B)

Where M is the mass of the ion, q is its charge, r is the position vector, t is time, E is the electric field, B is the magnetic field, and v is the velocity vector.

Now, let's introduce a new time scale τ = kt. By substituting this into the equation of motion, we have:

M(d²r/d(kt)²) = q(E + (dr/d(kt)) × B)

Differentiating both sides with respect to t, we get:

M/k²(d²r/dt²) = q(E + (1/k)(dr/dt) × B)

Since the second ion has a mass of kM, we can rewrite the equation as:

(kM)(d²r/dt²) = (q/k)(E + (1/k)(dr/dt) × B)

This equation indicates that the ion of mass kM will experience an effective electric field of E/k and an effective magnetic field of B when moving along the same trajectory. Therefore, the ion of mass kM will indeed follow the same path as the ion of mass M in the original fields E and B, as stated by Bleakney's theorem.

Learn more about equation here

brainly.com/question/29538993

#SPJ11

The exhaust gas is leaving the rocket engines at a velocity of -4.1 m/s.

The rocket is accelerating upwards at 5.7 m/s. This means that the exhaust gas is also accelerating upwards at 5.7 m/s. However, the exhaust gas is also being expelled from the rocket, which means that it is also gaining momentum in the opposite direction.

The total momentum of the exhaust gas is equal to the momentum of the rocket, so the velocity of the exhaust gas must be equal to the velocity of the rocket in the opposite direction. Therefore, the velocity of the exhaust gas is -5.7 m/s.

Velocity of exhaust gas = -velocity of rocket

= -5.7 m/s

To learn more about exhaust velocity click here: brainly.com/question/33288283

#SPJ11

1. The motion of a student in the hall can be represented as follows:  The student initially moves towards the north direction and reaches a maximum displacement of 5m. The student then turns back and moves towards the south direction and attains a maximum displacement of -2m.

The student then moves towards the north direction and attains a final displacement of 4m before coming to a stop.2. The displacement in the north direction can be calculated as follows:

Displacement = final position - initial position= 4 - 0 = 4mTherefore, the displacement in the north direction is 4m.

3. The displacement in the south direction can be calculated as follows: Displacement = final position - initial position= -2 - 5 = -7mTherefore, the displacement in the south direction is -7m.

4. The time it travelled north can be calculated as follows:

Time taken = final time - initial time= 8 - 0 = 8sTherefore, the time it travelled north is 8s.5.

To know more about maximum visit:

https://brainly.com/question/30693656

#SPJ11

A cylindrical copper cable carries a current of 1200 A. There is a potential difference of 0.016 V between two points on the cable that are 0.24 m apart.

The resistivity of copper is 1.7 x 10^-8 Ωm.

The formula for resistance is:

R = (ρl)/AR is resistanceρ is resistivity l is the length of the wireA is cross-sectional area of wire, the formula for cross-sectional area is:

[tex]A = (ρl)/RA = (ρl)/R= (1.7 x 10^-8 Ωm * 0.24 m)/((0.016 V)/1200 A))A = 5.1 x 10^-6 m^2[/tex]

Now, using the formula for cross-sectional area of a cylinder:

[tex]A = πd²/4We can write: πd²/4 = 5.1 x 10^-6 m^2d² = (4 * 5.1 x 10^-6 m^2)/πd² = 1.63 x 10^-6 m²d = √(1.63 x 10^-6 m²)d = 1.28 x 10^-3 m = 1.28 mm,[/tex]

the diameter of the copper cable is 1.28 mm.

To know about diameter visit:

https://brainly.com/question/32968193

#SPJ11

The small contribution to the magnetic field dB at point P due to just a small segment of the current carrying wire of length dx at the origin is given by dB = (μ0 / 4π) * (I * dx) / r^2.

An infinitely long straight wire is aligned along the x-axis, with a current I = 2.00A flowing in the positive x-direction. We consider a position P located at (x, y, z) = (2.00cm, 5.00cm, 0), near the wire. The question asks for the small contribution to the magnetic field, dB, at point P due to a small segment of the current-carrying wire with length dx located at the origin.

The magnetic field produced by a current-carrying wire decreases with distance from the wire. For an infinitely long, straight wire, the magnetic field at a distance r from the wire is given by B = (μ0 * I) / (2π * r), where μ0 is the permeability of free space (μ0 ≈ 4π x 10^(-7) T m/A).

To determine the contribution to the magnetic field at point P from a small segment of the wire with length dx located at the origin, we can use the formula for the magnetic field produced by a current element, dB = (μ0 / 4π) * (I * (dl x r)) / r^3, where dl represents the current element, r is the distance from dl to point P, and dl x r is the cross product of the two vectors.

In this case, since the wire segment is located at the origin, the distance r is simply the distance from the origin to point P, which can be calculated using the coordinates of P. Therefore, the small contribution to the magnetic field at point P due to the wire segment is given by dB = (μ0 / 4π) * (I * dx) / r^2, where r is the distance from the wire to point P, and μ0 is the permeability of free space.

Hence, the small contribution to the magnetic field dB at point P due to just a small segment of the current carrying wire of length dx at the origin is given by dB = (μ0 / 4π) * (I * dx) / r^2, where r is the distance from the wire to point P, μ0 is the permeability of free space, I is the current in the wire, and dx is the length of the wire segment.

Learn more about magnetic field at: https://brainly.com/question/14411049

#SPJ11

The final momentum of the combined objects is 14.2 kgm/s in the direction of the small asteroid.

The final momentum of the combined objects is calculated by applying the following formula for conservation of linear momentum.

m₁u₁ + m₂u₂ = v(m₁ + m₂)

where;

The final velocity is calculated as;

10 x (-15) + 10( 17 cos15) = v (10 + 10)

-150 + 164.2 = 20v

14.2 = 20v

v = (14.2 ) / 20

v = 0.71 m/s in the direction of the small asteroid

The final momentum is calculated as;

P = 0.71 m/s (10 kg + 10 kg)

P = 14.2 kg m/s

Learn more about linear momentum here: https://brainly.com/question/7538238

#SPJ4

The water temperature in degrees Celsius after half an hour is approximately 41.63 °C.

Given data: Resting metabolic rate = 6.330 × 105 Joule/h , Mass of water in the tub = 2.300 × 103 kg , Initial temperature of water = 27.60°C Time = 0.5 hour . To find Water temperature in degree Celsius after half an hour ,Formula  Q = mcΔT Where, Q = Heat absorbed by the water, m = Mass of water, c = Specific heat of water, ΔT = Change in temperature of water.

We can calculate heat absorbed by the water using the formula, Q = m×c×ΔT. Substitute the values given in the question, Q = 2300 × 4.18 × ΔTWe know that, Q = mcΔTm = 2300 × 10³ g = 2300 kg, c = 4.18 J/g°C. We can find the temperature difference using the formula, Q = m × c × ΔTΔT = Q/mc. Substitute the values,ΔT = Q/mcΔT = (6.33 × 10⁵ × 0.5 × 3600) / (2300 × 4.18)ΔT = 14.03°C.

Temperature of water after half an hour = Initial temperature + Temperature difference= 27.6 + 14.03= 41.63°C.

Therefore, the water temperature in degrees Celsius after half an hour is approximately 41.63 °C.

Let's learn more about Heat:

https://brainly.com/question/13439286

#SPJ11

Answer: The distance between lines on the diffraction grating that produces a second-order maximum for 760-nm red light at an angle of 60° is 2.01 µm.

A diffraction grating consists of a large number of equally spaced parallel slits or lines. When a beam of light is incident on a grating, it is diffracted and results in constructive and destructive interference. The intensity of the light is greatest when the waves are in phase and least when they are out of phase.

The relationship between the angle of diffraction θ, the wavelength of light λ, and the distance between the lines on the diffraction grating d is given by the equation:

nλ = d(sinθ)

where n is the order of the diffraction maximum. In this case, we are given that the red light has a wavelength of λ = 760 nm and that the second-order maximum occurs at an angle of θ = 60°.

We can rearrange the equation above to solve for d:d = nλ / sinθ

Plugging in the values given, we get: d = 2(760 nm) / sin(60°)≈ 2.01 µm.

Thus, the distance between lines on the diffraction grating that produces a second-order maximum for 760-nm red light at an angle of 60° is 2.01 µm.

Learn more about diffraction: https://brainly.com/question/29451443

#SPJ11

The angle at which the second minimum will occur is approximately 70.34°. Hence, option (c) 69.90° is the closest correct answer.

First minimum (m = 1) for 633 nm light occurs at an angle of 28.09°.

We need to find the angle at which the second minimum (m = 2) will occur.

Using the formula for the position of the nth minimum in a single slit diffraction:

d * sin(theta) = n * lambda

where:

d is the width of the slit,

theta is the angle of diffraction,

lambda is the wavelength of light,

n is the order of the minimum.

For the first minimum (m = 1):

d * sin(theta_1) = 1 * lambda

For the second minimum (m = 2):

d * sin(theta_2) = 2 * lambda

Dividing the equation for the second minimum by the equation for the first minimum:

sin(theta_2) / sin(theta_1) = (2 * lambda) / lambda

sin(theta_2) / sin(theta_1) = 2

To find theta_2, we need to take the inverse sine (arcsine) of both sides:

theta_2 = arcsin(2 * sin(theta_1))

Substituting the given angle for the first minimum:

theta_2 = arcsin(2 * sin(28.09°))

Calculating this expression, we find:

theta_2 ≈ 70.341732°

Therefore, the angle at which the second minimum will occur is approximately 70.34°. Hence, option (c) 69.90° is the closest correct answer.

Learn more about diffraction at: https://brainly.com/question/8645206

#SPJ11

Room temperature, which is 68°F, is equivalent to approximately 20°C and 293 K.

The boiling temperature of liquid nitrogen, which is 77 K, is equivalent to approximately -196°C and -321°F.

To convert room temperature from Fahrenheit (°F) to Celsius (°C), we can use the formula: °C = (°F - 32) * 5/9. Substituting 68°F into the formula, we get: °C = (68 - 32) * 5/9 ≈ 20°C.

To convert from Celsius to Kelvin (K), we simply add 273.15 to the Celsius value. Therefore, 20°C + 273.15 ≈ 293 K.

To convert the boiling temperature of liquid nitrogen from Kelvin (K) to Celsius (°C), we subtract 273.15. Therefore, 77 K - 273.15 ≈ -196°C.

To convert from Celsius to Fahrenheit, we can use the formula: °F = (°C * 9/5) + 32. Substituting -196°C into the formula, we get: °F = (-196 * 9/5) + 32 ≈ -321°F.

Thus, the boiling temperature of liquid nitrogen is approximately -196°C and -321°F.

To know more about Boilling Temperature :

brainly.com/question/1817366

#SPJ11

Here is a physics diagram illustrating the given problem:

```

          +------------------------+

          |                        |

          |   Charged Conducting   |

          |        Sphere          |

          |      (Radius r1)       |

          |                        |

          +------------------------+

          +------------------------+

          |                        |

          |   Uncharged Conducting |

          |        Sphere          |

          |   (Inner Radius r2)    |

          |                        |

          +------------------------+

                      |

                      | (Outer Radius r3)

                      |

                      V

         ----------------------------

        |                            |

        |         Capacitor          |

        |                            |

         ----------------------------

```

To determine the charge Qo on the isolated conducting sphere, we can use the formula for the potential of a conducting sphere:

V = kQo / r1

where V is the potential, k is the electrostatic constant, Qo is the charge, and r1 is the radius of the sphere.

Rearranging the equation, we can solve for Qo:

Qo = V * r1 / k

Substituting the given values, we have:

Qo = (-2000V) * (0.20m) / (8.99 x [tex]10^9 N m^2/C^2[/tex])

Evaluating this expression will give us the value of Qo on the isolated conducting sphere.

Learn more about conducting spheres, here:

https://brainly.com/question/30857607

#SPJ4