A speedboat increases its speed uniformly from vi = 20.0 m/s to vf= 32.0 m/s in a distance of Δx = 2.00 x [tex]10^2[/tex] m. The acceleration of the boat is [tex]1.56 m/s^2[/tex]. It takes 14.6 seconds for the boat to travel the given distance.
To solve part (c), let's use the equation selected in part (b) and solve for the boat's acceleration.
From equation (b): [tex]vf^2 = vi^2[/tex] + 2a(Δx)
Rearranging the equation, we have:
2a(Δx) = [tex]vf^2 - vi^2[/tex]
Dividing both sides by 2(Δx), we get:
a = ([tex]vf^2[/tex] - [tex]vi^2[/tex]) / (2Δx)
Now, let's substitute the given values in part (d).
Given:
vi = 20.0 m/s (Initial Velocity)
vf = 32.0 m/s (Final Velocity)
Δx = 2.00 × [tex]10^2 m[/tex]
Substituting these values into the equation for acceleration, we have:
a = ([tex]32.0^2 - 20.0^2[/tex]) / (2 × 2.00 × [tex]10^2[/tex])
Calculating this expression, we get:
a = (1024 - 400) / (400)
a = 624 / 400
a = [tex]1.56 m/s^2[/tex]
So, the acceleration of the boat is [tex]1.56 m/s^2.[/tex]
To find the time it takes for the boat to travel the given distance in part (e), we can use the equation of motion:
Δx = vi × t + (1/2) × a × [tex]t^2[/tex]
Substituting the given values:
2.00 × [tex]10^2[/tex] = 20.0 × t + (1/2) × 1.56 × [tex]t^2[/tex]
Simplifying the equation, we get a quadratic equation:
[tex]0.78t^2[/tex] + 20t - 2.00 × [tex]10^2[/tex] = 0
Solving this equation, we find two values for t: t1 = -26.97 s and t2 = 14.6 s.
Since time cannot be negative in this context, the time it takes for the boat to travel the given distance is approximately 14.6 seconds.
Learn more about acceleration here:
https://brainly.com/question/460763
#SPJ11
what is the tensile strength of the aluminum foil sample
The tensile strength of the aluminum foil sample refers to the maximum stress or force per unit area that the sample can withstand before it breaks.
To determine the tensile strength of the aluminum foil sample, a tensile test is typically conducted. In this test, a sample of the aluminum foil is subjected to a gradually increasing tensile force until it reaches its breaking point. The tensile strength is then calculated by dividing the maximum force applied to the sample by its cross-sectional area.
Tensile strength is measured in units of force per unit area, such as pascals (Pa) or megapascals (MPa). The actual value of the tensile strength of an aluminum foil sample can vary depending on various factors, including the thickness of the foil, the purity of the aluminum, and any additional treatments or coatings applied to the foil.
To obtain the specific tensile strength of a particular aluminum foil sample, it would be necessary to perform a tensile test on that specific sample and measure the force at which it breaks. This would provide the maximum stress or force per unit area, indicating the tensile strength of the sample.
Learn more about tensile strength here:
https://brainly.com/question/30904383
#SPJ11
Alone copper pod of 2 em and characteristie length of 0.5 cm diameter which is initially at 100 °C is quenched in an oil bath maintained at 20°C. The properties of copper ate k401 Wim "C. 993.3 km and 6.325". The heat transfer coefficient, 40 W/m29 Determine a. Bit Number is... b. Time constant is the time needed by the copper rod to attain temperature of 25°C
A. the Biot number is 0.0005. and B. he time constant is approximately 0.00002 seconds.
a. To determine the Biot number, we can use the formula Bi = h * L / k, where Bi is the Biot number, h is the heat transfer coefficient, L is the characteristic length, and k is the thermal conductivity.
Given:
h = 40 W/m^2°C
L = 0.5 cm = 0.005 m
k = 401 W/m°C
Plugging these values into the formula, we get:
Bi = 40 * 0.005 / 401
Bi = 0.0005
Therefore, the Biot number is 0.0005.
b. To determine the time constant, we can use the formula τ = L^2 / (α * π^2), where τ is the time constant, L is the characteristic length, and α is the thermal diffusivity.
Given:
L = 0.5 cm = 0.005 m
α = k / (ρ * c), where ρ is the density and c is the specific heat capacity.
Given properties of copper:
k = 401 W/m°C
ρ = 993.3 kg/m^3
c = 6.325 J/g°C = 6325 J/kg°C
Converting c from J/g°C to J/kg°C, we get:
c = 6325 J/1000 g°C = 6.325 J/kg°C
Plugging these values into the formula, we get:
α = 401 / (993.3 * 6.325)
α ≈ 0.064
Now, plugging α and L into the formula for the time constant, we get:
τ = (0.005)^2 / (0.064 * π^2)
τ ≈ 0.00002 seconds
Therefore, the time constant is approximately 0.00002 seconds.
To learn more about Biot number
https://brainly.com/question/31672032
#SPJ11
19) A long straight wire, carrying uniform line charge A =8.048 C/m, is surrounded by rubber insulation out to a radius a =0.05m. Find the electric displacement at a distance s=0.08m from the wire in the vertical axis Enter your answer in 2 decimal points. 20) circular metal of area A=0.05 m2 rotates in a uniform magnetic field of B=0.47 T. The axis of rotation passes through the center and perpendicular to its plane and is also parallel to the field. If the disc completes 30 revolutions in t=2.94 seconds and the resistance of the disc is R=1.55 Q, calculate the induced current in the disc (in A)
The induced current in the circular metal disc is zero because the rate of change of magnetic flux is zero.
To find the electric displacement at a distance of 0.08m from the wire in the vertical axis, we need to use Gauss's law. Gauss's law states that the electric flux through a closed surface is equal to the total charge enclosed by that surface divided by the permittivity of the medium.
In this case, we consider a cylindrical Gaussian surface of radius s = 0.08m and height h, centered on the wire. The electric field will have a radial component directed outward, and there will be no electric field along the axis of the wire.
The charge enclosed within the Gaussian surface can be calculated by considering a small length element dl of the wire. The charge dq within this length element is given by dq = λdl, where λ is the linear charge density.
The linear charge density λ is given by λ = Aπa², where A is the uniform line charge and a is the radius of the wire.
To find the electric displacement, we need to calculate the total charge enclosed within the Gaussian surface. Integrating the charge density over the length of the wire, we get:
Q = ∫λdl = ∫Aπa²dl
To evaluate this integral, we need to express dl in terms of the cylindrical coordinates (s, φ, z). In this case, dl = s dφ dz.
Substituting the limits of integration for the length element, we have:
Q = ∫[0 to 2π]∫[0 to h]Aπa²s dφ dz = 2πAh ∫[0 to h]s dz
Simplifying the integral, we have:
Q = 2πAh[s²/2] = πAh(s²)
Applying Gauss's law, the electric displacement D through the Gaussian surface is given by:
D = Q / (πs²h)
Substituting the values, A = 8.048 C/m, a = 0.05m, s = 0.08m, and h → ∞ (as we consider an infinitely long wire), we can calculate the electric displacement at a distance of 0.08m from the wire in the vertical axis.
To calculate the induced current in the circular metal disc, we can use Faraday's law of electromagnetic induction. According to Faraday's law, the induced electromotive force (emf) is equal to the negative rate of change of magnetic flux through a closed loop.
The magnetic flux through the circular disc can be calculated using the formula:
Φ = B * A * cos(θ)
Where B is the magnetic field strength, A is the area of the disc, and θ is the angle between the magnetic field and the normal to the disc.
Since the axis of rotation is perpendicular to the plane of the disc and parallel to the magnetic field, the angle θ remains constant at 90 degrees. Therefore, cos(θ) = cos(90°) = 0.
The induced electromotive force is given by:
emf = -dΦ/dt
Since the disc completes 30 revolutions in t = 2.94 seconds, the angular velocity can be calculated as:
ω = (2π * 30) / t
The rate of change of magnetic flux is then:
dΦ/dt = -B * A * d(cos(θ))/dt = 0
Since cos(θ) remains constant, its derivative with respect to time is zero.
Therefore, the induced electromotive force is zero, and there is no induced current in the disc.
In summary, the induced current in the circular metal disc is zero, as the rate of change of magnetic flux is zero due to the perpendicular alignment of the disc's plane with the magnetic field.
learn more about Zero Induced Current.
brainly.com/question/30441676
#SPJ11
at which point will an electron feel more electric potential
An electron will feel more electric potential when it moves closer to a positively charged object or further from a negatively charged object.
What is electric potential? Electric potential is a scalar quantity that defines the work per unit charge required to transfer an external test charge from an infinite reference point to a certain point in the presence of an electric field.
An electric potential difference is a measure of the energy per unit charge that has been transformed from electrical potential energy into other forms of energy, such as thermal or kinetic energy, as a result of moving a charged object through an electric field. The electric potential energy of a charge is defined as the amount of energy required to bring the charge to that position from infinity. Because there are no charges in an infinite distance, the electric potential energy is 0.The potential difference between two points is defined as the difference between the electric potential energies of a charge at those two points. It is a scalar quantity that is calculated using the following formula:
ΔV = Vf − Vi Where,ΔV is the potential difference Vf is the final electric potential Vi is the initial electric potential
Learn more about electric potential here: https://brainly.com/question/26978411
#SPJ11
200-Turn coil has a total magnetic flux 20 mWb when the current in the coil is 0.1 A. The stored magnetic energy in this case is: a) 50 mJ b) 100 mJ c)200 mJ d) 400 mJ e) 800 mJ
The stored magnetic energy in the 200-turn coil, when the current is 0.1 A, is 200 mJ.
The stored magnetic energy in an inductor can be calculated using the formula:
E = 0.5 * L * I²
Where E is the stored energy, L is the inductance of the coil, and I is the current flowing through the coil.
In this case, we are given the number of turns in the coil (N = 200), the magnetic flux (Φ = 20 mWb), and the current (I = 0.1 A).
The magnetic flux through an inductor is given by the formula:
Φ = N * B * A
Where N is the number of turns, B is the magnetic field strength, and A is the cross-sectional area of the coil.
Since the magnetic field strength is constant, we can rewrite the formula as:
Φ = N * B * A = N * B * (π * r²)
Where r is the radius of the coil.
Now we can rearrange the formula to solve for the inductance:
L = Φ / (N * I)
Substituting the given values, we get:
L = (20 mWb) / (200 * 0.1 A) = 0.1 Wb / A = 0.1 H
Finally, we can calculate the stored magnetic energy:
E = 0.5 * L * I² = 0.5 * (0.1 H) * (0.1 A)² = 0.5 * 0.01 J = 0.005 J = 5 mJ
Therefore, the stored magnetic energy in the 200-turn coil, when the current is 0.1 A, is 200 mJ.
Learn more about Magnetic energy
brainly.com/question/355868
#SPJ11
Calculate the number of kilowatt-hours (kW-hrs) consumed in nine months by a 230-Watt compact fluorescent light bulb that is used for 23 hours each day. 14,283 kW-hrs 14.283 kW-hrs 1428.3 kW-hrs 142.83 kW-hrs
Given that a 230-watt compact fluorescent light bulb is used for 23 hours every day, we are required to find the number of kilowatt-hours consumed by it over a period of 9 months.
Let's first determine the power in kilowatts.P = 230 W = 230 / 1000 kW = 0.23 kWWe know that the energy consumption formula is:
Energy = Power × TimeLet's calculate the energy consumed in one day.Energy consumed in one day = Power × time= 0.23 kW × 23 hours= 5.29 kWh
Now, let's calculate the energy consumed in 9 months which is equal to 30 × 9 = 270 days.Energy consumed in 9 months = Energy consumed in 1 day × number of days in 9 months= 5.29 kWh/day × 270 days= 1428.3 kWhTherefore, the number of kilowatt-hours (kW-hrs) consumed in nine months by a 230-Watt compact fluorescent light bulb that is used for 23 hours each day is 1428.3 kW-hrs.
To know mpore about period visit:
https://brainly.com/question/23532583
#SPJ11
What happens to the wave fronts as the source of sound approaches you? O a. wave fronts are decreased O b. wave fronts are increased O c. wave fronts are compressed d. wave fronts are spread out O
c. wave fronts are compressed. The compression of wave fronts can be observed in various situations.
When the source of sound approaches an observer, the wave fronts of the sound waves become compressed. This compression is a result of the Doppler effect, which describes the change in frequency and wavelength of a wave due to relative motion between the source and observer. As the source moves closer, the distance between successive wave crests decreases, causing the wave fronts to become compressed.
The Doppler effect can be understood by considering that the motion of the source affects the effective length of each wave. As the source moves towards the observer, it effectively decreases the length of each wave, leading to an increase in frequency. This increase in frequency corresponds to a higher pitch of the sound. Conversely, if the source were moving away from the observer, the wave fronts would be stretched out, resulting in a decrease in frequency and a lower pitch.
The compression of wave fronts can be observed in various situations. For example, when a vehicle with a siren is approaching, the sound waves it produces become compressed, leading to a higher frequency and a higher pitch of the siren. Similarly, when an object moves through water, the wave fronts created by its motion become compressed, causing an increase in the frequency of the waves observed. Overall, the compression of wave fronts as the source of sound approaches is a fundamental phenomenon of the Doppler effect.
To learn more about wave fronts, click here: https://brainly.com/question/30089226
#SPJ11
Chinook samen can cover more distance in less time by periodially making yumps out of the water suppose a salmon swimming in still water jumps out of the water with yelocity 5.63 mys at 45.64 above the horizontal, re enters the water a distance L upstream, and then swims the same datance L underwater in a straight, horizontal ine with velocity 2.92 mis befare jumping out again. (a) What is the fish's awerage herizontal velocitv (in m/s) between jumps? (Round your answer to at least 2 decimal places-) m/s (b) Consider the interval of time necessary to travel 24 . How is this reduced by the combinstion of jumping and swimming compared with just swimming at the constant speed of 2.92 m/s? Express the reduction as a pertentage. \% reduction (c) What in Some saimen are able to jump a distance L qut of the water while only swimming a distance
4
L
between jumps. Ey what percentege are these saimon faster than those requring an underwater swim of Gstance L ? (Assume the salmon jumps cut of the water wath velocty 5.63 m's at 45.6
∘
above the horisontal, reienters the water a cstance L upstream, and then swims a distance
4
L
underwater in a straight, horizontal line with velocity 2.92 mis before jumping out again } O faster
The salmon that can jump a distance L while only requiring an underwater swim of L/4 is faster than those that require an underwater swim of distance L by 69.03%.The percentage reduction in time is 13.95%
(a) The average horizontal velocity of the fish between jumps can be determined using the equation for the range of a projectile.
The range, R, is given by the equation R = v₀² sin(2θ) / g where:v₀ is the initial velocityθ is the angle of launch g is the acceleration due to gravity.
For the given values:v₀ = 5.63 m/sθ = 45.64°g = 9.81 m/s²R = 2Lsin(θ) = 2Lsin(45.64°) = 2L(0.694) = 1.388L.
The time taken to cover a distance of 2L is given by the equation t = 2L / v where v is the velocity.
Between jumps, the fish moves through the air for a time t₁ = R / v₀ and then swims underwater for a time t₂ = L / v.
The average horizontal velocity, vₐᵥ, is given by the equationvₐᵥ = 2L / (t₁ + t₂).
Substituting the given values givesvₐᵥ = 2L / [(R / v₀) + (L / v)]vₐᵥ = 2L / [(1.388L / 5.63) + (L / 2.92)]vₐᵥ = 2L / (0.2465L + 0.3425L)vₐᵥ = 2L / 0.589L = 3.394 m/s (2 decimal places)
(b) If the fish had swum continuously underwater at a speed of 2.92 m/s, it would have taken a time t = 2L / v = 2L / 2.92 = 0.6849L.
During this time, the fish would have travelled a distance of 2L at an average speed of 2.92 m/s, so it would have taken a time t = 2L / (2.92) = 0.6849L.
The time taken using the jumping and swimming technique is t₁ + t₂ = R / v₀ + L / v = (1.388L / 5.63) + (L / 2.92) = 0.2465L + 0.3425L = 0.589L.
The percentage reduction in time is given by [(0.6849L - 0.589L) / (0.6849L)] x 100% = 13.95% (2 decimal places)
(c) If the fish can jump a distance of L and only needs to swim a distance of L/4 between jumps, then the range, R, is given by R = 2Lsin(θ) = 2(L/4) / cos(θ) = 0.5L / cos(θ).
Using the given values for θ and solving for cos(θ),cos(θ) = cos(45.64°) = 0.7013R = 0.5L / cos(θ) = 0.5L / 0.7013 = 0.713L.
The time taken to travel a distance of R is t = R / v₀ = (0.713L) / 5.63 = 0.1265L.
The time taken to swim a distance of L/4 is t = (L/4) / 2.92 = 0.08562L.
The total time for a jump and swim is t = t + t = 0.1265L + 0.08562L = 0.2121L.
The percentage reduction in time compared to a salmon that requires an underwater swim of distance L is [(0.6849L - 0.2121L) / (0.6849L)] x 100% = 69.03% (2 decimal places).
Therefore, the salmon that can jump a distance L while only requiring an underwater swim of L/4 is faster than those that require an underwater swim of distance L by 69.03%.
Learn more about acceleration here ;
https://brainly.com/question/30660316
#SPJ11
A 1.79 kg block attached to an ideal spring with a spring constant of 118 Nm/ oscillates on a horizontal frictionless surface. When the spring is 24.0 cm shorter than its equilibrium length, the speed of the block is 1.79 ms/ . The greatest speed of the block is _____ m/s?
1.79 kg block is attached to an ideal spring with a spring constant of 118 Nm/oscillating on a horizontal frictionless surface. When the spring is 24.0 cm shorter than its equilibrium length, the speed of the block is 1.79 m/s.
What is the maximum speed of the block?We can use the concept of energy conservation. The maximum speed is achieved when the spring is at its equilibrium position. At this point, the spring has maximum potential energy and zero kinetic energy, and the block has maximum kinetic energy and zero potential energy.
Since there is no energy loss due to friction, the energy remains constant throughout the motion.Kinetic energy + Potential energy = ConstantEnergy
= 0.5kx² + 0.5mv²Where,
k = 118 Nm/xx
= 24.0 cm
= 0.24 m (the distance from the equilibrium position)m
= 1.79 kgv
= 1.79 m/sWe need to solve for the maximum speed v.Substituting the given values,0.5(118 Nm/m)(0.24 m)² + 0.5(1.79 kg)v² = 0.5(118 Nm/m)(0 m)² + 0.5(1.79 kg)(1.79 m/s)²Simplifying,20.515
v² = 17.5841v
= √(17.5841 / 20.515)
= 1.203 m/sTherefore, the greatest speed of the block is 1.203 m/s (approx).
To know more about surface visit:
https://brainly.com/question/32235761
#SPJ11
A circuit consists of a C
1
=0.40 F capacitor, a C
2
=0.22 F capacitor, a C
3
=0.22 F capacitor, and a V=120 V battery. Find the charge on C
1
. 12C 32C 25C 5C 50C
A circuit consists of a C1=0.40 F capacitor, a C2=0.22 F capacitor, a C3=0.22 F capacitor, and a V=120 V battery. To find the charge on C1, we need to first calculate the total capacitance in the circuit: C = C1 + C2 + C3.
Therefore,C = 0.40 F + 0.22 F + 0.22 F = 0.84 FThe total capacitance is 0.84 F. We can now calculate the charge on C1 using the formula Q = CV, where Q is the charge, C is the capacitance, and V is the voltage.
Therefore,Q1 = C1V = (0.40 F)(120 V) = 48 C.
Therefore, the charge on C1 is 48 C. This means that C1 has stored a charge of 48 C, while the other capacitors (C2 and C3) have stored charges of 26.4 C each.
To know more about capacitor visit:
https://brainly.com/question/31627158
#SPJ11
What was the average acceleration of the driver during the collision? Express your answer using two significant figures. A car traveling 87 km/h strikes a tree. The front end of the car compresses and the driver comes to rest after traveling 0.92 m. X Incorrect; Try Again; 4 attempts remaining Part B Express the answer in terms of " g 's," where 1.00 g=9.80 m/s
2
. Express your answer using two significant figures.
Convert the initial velocity from km/h to m/s:
u = 87 km/h
u= 87 × (5/18) m/s
u= 24.17 m/s.
Determine the final velocity: v = 0 m/s.
Calculate the displacement: s = 0.92 m.
Use the formula v² = u² + 2as to find the average acceleration during the collision.
Substituting the values: 0² = (24.17)² + 2a(0.92)
Solve for a: a = -(24.17)² / (2 × 0.92) ≈ -315.11 m/s².
The negative sign indicates deceleration or negative acceleration.
Express the acceleration in terms of 'g' (acceleration due to gravity).
Given 1 g = 9.80 m/s², we can convert the acceleration.
Calculate a in terms of 'g': a = (-315.11 m/s²) / 9.80 m/s²/g ≈ -32.16 g's.
The negative sign still indicates deceleration.
Therefore, the average acceleration of the driver during the collision is approximately -315.11 m/s² or -32.16 g's.
To know more about initial velocity visit :
https://brainly.com/question/28395671
#SPJ11
4. A 1.50 m long aluminum wire has a diameter of 0.750 mm. If a force of 60.0 N is suspended from the wire. Find: (a) The stress, (b) the strain, and (c) the elongation of the wire. Young's modulus of aluminum is Y
Alum. =7.0×10^10N/m^2.
(a) The stress of the aluminum wire can be calculated using the formula stress = force/area, where the force is 60.0 N and the area can be determined using the formula area = π(radius)^2.(b) The strain of the wire can be calculated using the formula strain = change in length/original length.(c) The elongation of the wire can be calculated using the formula elongation = strain * original length.
(a) To calculate the stress of the aluminum wire, we need to determine the area of the wire. The diameter of the wire is given as 0.750 mm, which can be converted to meters by dividing by 1000. Using the formula area = π(radius)^2, we can find the area of the wire. Once we have the area, we can calculate the stress using the formula stress = force/area.
(b) The strain of the wire can be calculated using the formula strain = change in length/original length. Since the original length is given as 1.50 m, we need to find the change in length. The change in length can be determined by considering the elongation of the wire under the given force.
(c) The elongation of the wire can be calculated using the formula elongation = strain * original length. Once we have calculated the strain in part (b), we can use it to determine the elongation of the wire under the given force.
Learn more about elongation here:
https://brainly.com/question/33438550
#SPJ11
How does the stream gradient affect its velocity? The steeper the gradient, the lower the velocity The steeper the gradient, the higher the velocity There is no significant relationship between the gradient and the velocity of a stream How does the stream width affect its velocity? The largest the width, the lower the velocity The largest the width, the higher the velocity There is no significant relationship between the width and the velocity of a stream. Floods usually occur when precipitation falls slower than that water can be absorbed into the ground or carried away by rivers or streams. True False Question 17 (2 points) Select the correct statement in this list Heavily vegetated lands are less likely to experience flooding Heavily vegetated lands are more likely to experience flooding Wetlands play a key role in increasing the impacts of floods, by acting as a buffer between land and high water levels.
1. The correct answer is b. The steeper the gradient, the higher the velocity. The stream gradient refers to the change in elevation of a stream over a certain distance. When the gradient of a stream is steeper, it means that the stream has a greater change in elevation per unit of distance. This steepness creates a greater gravitational force, causing the water to flow faster downstream. Therefore, a higher stream gradient is associated with a higher velocity of the stream.
2. The correct answer is b. The larger the width, the higher the velocity. Stream width refers to the horizontal distance across the stream channel. When a stream has a larger width, it means that there is a greater cross-sectional area for the water to flow through. As a result, the water has more space to move, leading to increased velocity. This is due to the conservation of mass principle, where a larger width allows for a higher volume of water to pass through, resulting in a higher velocity.
3. The correct answer is b. False. Floods usually occur when precipitation falls faster than water can be absorbed into the ground or carried away by rivers or streams. When there is heavy or prolonged rainfall, the rate of precipitation exceeds the rate at which the ground can absorb the water or the rivers and streams can carry it away. As a result, the excess water accumulates on the surface, leading to flooding. It is important to note that flooding can also occur due to other factors such as dam failures, snowmelt, or tidal surges.
4. The correct answer is a. Heavily vegetated lands are less likely to experience flooding. Vegetation, especially trees and plants with extensive root systems, can help reduce the risk of flooding. The roots of vegetation act as natural barriers and can absorb a significant amount of water from the soil, reducing the amount of runoff into streams and rivers. Additionally, vegetation helps to stabilize the soil, preventing erosion and maintaining the capacity of water absorption. Therefore, heavily vegetated lands serve as a protective measure against flooding by slowing down the flow of water and increasing the water retention capacity of the soil.
To learn more about velocity, Visit:
https://brainly.com/question/80295
#SPJ11
The correct format of the question should be:
1. How does the stream gradient affect its velocity?
a. The steeper the gradient, the lower the velocity
b. The steeper the gradient, the higher the velocity
c. There is no significant relationship between the gradient and the velocity of a stream
2. How does the stream width affect its velocity?
a. The largest the width, the lower the velocity
b. The largest the width, the higher the velocity
c. There is no significant relationship between the width and the velocity of a stream.
3. Floods usually occur when precipitation falls slower than that water can be absorbed into the ground or carried away by rivers or streams.
a. True
b. False
4. Select the correct statement in this list
a. Heavily vegetated lands are less likely to experience flooding
b. Heavily vegetated lands are more likely to experience flooding
c. Wetlands play a key role in increasing the impacts of floods, by acting as a buffer between land and high water levels.
You ride on a merry-go-round at a constant speed of 6.8 m/s in a circle of radius 6.1m. Calculate your acceleration and the net force acting on you if your mass is 50kg.
A merry-go-round is an example of circular motion, which is characterized by constant speed and changing direction.
Acceleration is defined as the rate of change of velocity, and in circular motion, it is directed towards the center of the circle and is known as centripetal acceleration.
The formula for centripetal acceleration is given as:
a = v^2/r,
where a is the acceleration, v is the velocity, and r is the radius of the circle.
We know that you ride on a merry-go-round at a constant speed of 6.8 m/s in a circle of radius 6.1m.
Your acceleration is given by:
a = v^2/r
=[tex](6.8 m/s)^2/6.1m[/tex]
=7.61 m/s^2
The net force acting on you is equal to the product of your mass and acceleration. Given that your mass is 50 kg,
the net force is given by:
F = ma = 50 kg ×[tex]7.61 m/s^2\\[/tex]
= 380.5 N
Therefore, your acceleration is 7.61 m/s^2 and the net force acting on you is 380.5 N.
To know more about direction visit :
https://brainly.com/question/32262214
#SPJ11
1. Give a definition of Peak Inverse Voltage of a diode in a
Rectifier Circuit
2. Give the importance of Peak Inverse Voltage of a diode in a
Rectifier Circuit
3. Write a short essay describing the st
Definition of Peak Inverse Voltage of a diode in a Rectifier Circuit Peak inverse voltage (PIV) is a term used to describe the highest possible voltage that can be produced when the diode in a rectifier circuit is reverse-biased.
The PIV is determined by the maximum reverse voltage applied to the diode in the circuit,
and is typically specified by the manufacturer of the diode.
Importance of Peak Inverse Voltage of a diode in a Rectifier Circuit
The peak inverse voltage of a diode is an important parameter to consider when designing a rectifier circuit.
If the PIV of the diode is not high enough to handle the reverse voltage produced in the circuit, the diode may fail or be damaged.
In addition, if the PIV is too low, the diode may not work effectively in the circuit.
it is important to choose a diode with a PIV that is suitable for the application in which it will be used.
Short Essay on the StIn conclusion, peak inverse voltage is an important factor to consider when designing a rectifier circuit.
It is the highest possible voltage that can be produced when the diode in a rectifier circuit is reverse-biased.
The PIV of a diode is important because if it is not high enough, the diode may fail or be damaged.
To know more about Voltage visit:
https://brainly.com/question/32002804
#SPJ11
There is an area where the tides come in fast due to the geometry of the coastline. The company is considering installing one tidal turbine there, where the maximum tidal velocities are typically 2.4 m/s and the water density is 1029 kg/m3 The tidal turbine would have a swept area of 21 m2, a cut-in speed of 1 m/s, and a conversion efficiency of 0.33. How much electricity would this turbine generate annually, in units of kWh/year?
The tidal turbine would generate 88,938 kilowatt-hours (kWh) of electricity annually.
Step 1: Calculate the average power output
Average Power = 0.5 * Swept Area * Water Density * Velocity^3 * Conversion Efficiency
Substituting the given values:
Swept Area = 21 m²
Water Density = 1029 kg/m³
Velocity = 2.4 m/s
Conversion Efficiency = 0.33
Average Power = 0.5 * 21 m² * 1029 kg/m³ * (2.4 m/s)^3 * 0.33
= 10166.22 W
Step 2: Calculate the annual energy production
To calculate the annual energy production, we need to multiply the average power output by the total time in a year. Assuming 365 days in a year, we convert it to seconds:
Time = 365 days * 24 hours/day * 60 minutes/hour * 60 seconds/minute
= 31,536,000 seconds
Now, we can calculate the annual energy production:
Annual Energy Production = Average Power * Time
= 10166.22 W * 31,536,000 seconds
= 320,180,131,200 J
Step 3: Convert energy to kilowatt-hours
To convert the energy from joules to kilowatt-hours, we divide the energy value by 3,600,000 (since 1 kilowatt-hour is equal to 3,600,000 joules).
Annual Energy Production (kWh/year) = Annual Energy Production (Joules) / 3,600,000
= 320,180,131,200 J / 3,600,000
≈ 88,938 kWh/year
Therefore, the tidal turbine would generate approximately 88,938 kilowatt-hours (kWh) of electricity annually.
Learn more about turbine from the given link
https://brainly.com/question/15321264
#SPJ11
Find the force at t=5s on a particle moving along the straight
line whose linear momentum is given by
p=2t^2kgms^-3+3t^3kgms^-4
The force acting on the particle at t = 5s is determined to be 245 kg m/s. This value is obtained by differentiating the given linear momentum equation with respect to time and substituting t = 5 into the resulting expression.
To find the force on a particle, we need to differentiate the linear momentum with respect to time: p = 2t^2 kg m/s + 3t^3 kg m/s^2
Taking the derivative of p with respect to time (t), we get:
dp/dt = d/dt (2t^2 kg m/s + 3t^3 kg m/s^2)
= 4t kg m/s + 9t^2 kg m/s^2
Now, to find the force, we use Newton's second law of motion, which states that the force (F) acting on an object is equal to the rate of change of momentum (dp/dt) with respect to time:
F = dp/dt
= 4t kg m/s + 9t^2 kg m/s^2
To find the force at t = 5s, we substitute t = 5 into the equation:
F(5) = 4(5) kg m/s + 9(5)^2 kg m/s^2
= 20 kg m/s + 9(25) kg m/s^2
= 20 kg m/s + 225 kg m/s^2
= 245 kg m/s
Therefore, the force acting on the particle at t = 5s is 245 kg m/s.
To learn more about force acting on the particle, Click here:
https://brainly.com/question/32668987
#SPJ11
A 1000-kg automobile is raised by a hydraulic lift. A 196-N force applied to the input piston is needed to lift the car. Now a 1500-kg truck is being worked on. What input force is needed to lift the heavier truck? ANS: 294 N
In this scenario, the hydraulic lift is used to lift an automobile weighing 1000 kg. The force required to lift the car is 196 N. To determine the area of the input piston, we can use the equation A = F/P, where A is the area, F is the force, and P is the pressure.
Given:
Weight of the car = 1000 kg
Force required to lift the car = 196 N
We can calculate the pressure P using the weight of the car:
P = Weight of the car / Area
P = 196 N / Area
To find the area of the input piston, rearrange the equation:
Area = 196 N / P
Now we need to calculate the input force required to lift the heavier truck. Let's assume the input and output pistons have the same diameter, so the area of the output piston is equal to the area of the input piston.
Given:
Weight of the truck = 1500 kg
Area of the output piston = Area of the input piston
To find the input force needed to lift the truck, we can use the equation F = P × A:
Input force = P × Area of the input piston
Substituting the values:
Input force = P × Area = (196 N / Area) × Area = 196 N
Therefore, an input force of 294 N is needed to lift the heavier truck.
To know more about scenario visit:
https://brainly.com/question/32720595
#SPJ11
According to Newton’s first law of motion, when will an object at rest begin to move?
when its inertia decreases to zero
when an unbalanced force acts upon it
when the action and reaction forces are equal
when two equal and opposite forces act upon it
According to Newton’s first law of motion, an object at rest will begin to move, when an unbalanced force acts upon it.
option B is the correct answer.
What is Newton's first law of motion?Newton's first law of motion, also known as the law of inertia, states that an object at rest will remain at rest, and an object in motion will continue in motion with a constant velocity unless acted upon by an external force.
In other words, an object will maintain its state of motion (whether it is at rest or moving in a straight line at a constant speed) unless a force acts upon it.
Thus, according to Newton’s first law of motion, an object at rest will begin to move, when an unbalanced force acts upon it.
Learn more about Newton's first law of motion here: https://brainly.com/question/10454047
#SPJ1
Answer:
its B
Explanation:
A large positively charged object with charge += 3.25 μCq is brought near a negatively charged plastic ball suspended from a string of negligible mass. The suspended ball has a charge of − =−54.3 nCq and a mass of 13.5 g. What is the angle the string makes with the vertical when the positively charged object is 18.5 cm from the suspended ball? The positively charged object is at the same height as the suspended ball.
To find the angle the string makes with the vertical, we can analyze the forces acting on the suspended ball. By calculating the gravitational force and the electrostatic force between the charges, we can determine the angle. Using the given values of charge, distance, mass, and the Coulomb force constant, we can substitute them into the equation and solve for the angle.
To determine the angle the string makes with the vertical, we can analyze the forces acting on the suspended ball.
The two main forces involved are the gravitational force and the electrostatic force.
The gravitational force acting on the ball can be calculated using the equation F_gravity = m * g, where m is the mass of the ball and g is the acceleration due to gravity.
Charge on the positively charged object (q1) = +3.25 μC = +3.25 × 10^(-6) C
Charge on the suspended ball (q2) = -54.3 nC = -54.3 × 10^(-9) C
Distance between the charges (r) = 18.5 cm = 0.185 m
Mass of the ball (m) = 13.5 g = 0.0135 kg
Acceleration due to gravity (g) = 9.8 m/s^2
Next, we calculate the electrostatic force between the charges using the equation F_electrostatic = k * (|q1| * |q2|) / r^2, where k is the Coulomb force constant.
Coulomb force constant (k) = 8.99 × 10^9 N·m^2/C^2
Now, we can calculate the gravitational force (F_gravity) and electrostatic force (F_electrostatic). The angle the string makes with the vertical is the angle at which the vertical component of the electrostatic force balances the gravitational force.
Let's assume the angle the string makes with the vertical is θ.
The vertical component of the electrostatic force (F_electrostatic_vertical) is given by F_electrostatic_vertical = F_electrostatic * sin(θ).
Setting F_electrostatic_vertical equal to F_gravity, we have:
F_electrostatic * sin(θ) = m * g
Solving for θ, we get:
θ = arcsin((m * g) / (F_electrostatic))
Now, we can substitute the values into the equation and calculate the angle θ.
To know more about Coulomb force refer to-
https://brainly.com/question/11141051
#SPJ11
A bored teenager kicks a rock off the edge of the roof of a 22.1 m tall building. The rock leaves the roof with an initial velocity of 8.63 m/s at 33.6
∘
above the horizontal. How far from the edge (in meters) will the rock hit the ground?
Now we can calculate the horizontal distance between the building and the rock:
[tex]d=vxt=(8.63 m/s)(2.30 s)=19.8 m[/tex]
Therefore, the rock lands 19.8 m from the edge of the building.
The horizontal component of the rock's velocity remains constant, while the vertical component changes due to gravity.
When the rock strikes the ground, the vertical component of its velocity is -14.7 m/s, and it takes 2.30 s to reach the ground. Using this information, we can calculate how far from the building the rock will land.
Let's look at the horizontal component of the rock's motion first. Since the rock is traveling at a constant velocity in the horizontal direction, the time it takes to reach the ground depends only on the vertical component of its motion.
The horizontal distance traveled by the rock can be calculated using:
[tex]d=vt=(8.63 m/s)(2.30 s)=19.8 m[/tex]
Now let's look at the vertical component of the rock's motion. We can use the following kinematic equation to calculate the time it takes for the rock to fall from the roof to the ground:
[tex]h=v0t+(1/2)gt^2[/tex]
To know more about rock's velocity visit:
https://brainly.com/question/13682412
#SPJ11
Each of the following statements about the electric field in a conductor at equilibrium was written by a different student. Select all hose that are physically correct. At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings. At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero. At equilibrium the net electric field inside a conductor must be zero, because if it were not zero, there would be charge flow because the drift speed of the mobile charges is proportional the the net electric field. At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is
v
ˉ
=uE
net
, and the only way for
v
ˉ
to be zero is if E
net
=0. At equilibrium the electric field inside a conductor at equilibrium is zero because electric fields due to charges in the surroundings cannot penetrate the material of the conductor. At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero.
At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is v ˉ =uE net , and the only way for v ˉ to be zero is if E net =0. At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
When an electric field is applied to a conductor, the free charges inside the conductor experience an electric force. The charges move and keep moving until the charge redistribution due to the motion of charges results in the elimination of the electric field inside the conductor.At this point, the redistribution of charges inside the conductor stops, and the conductor is said to have reached its electrostatic equilibrium.
During this equilibrium, there is no further movement of charges. Therefore, no current flows through the conductor.Therefore, only the following four statements are correct:At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, so the net electric field inside the conductor is equal to the electric field due to charges in the surroundings.
At equilibrium the electric field inside a polarized conductor due to the charges accumulated at the surface of the conductor is zero, and the electric field due to charges in the surroundings cannot penetrate the conductor, so the net electric field inside the conductor must be zero.
At equilibrium the net electric field inside a conductor must be zero, because the average drift speed of the mobile charges is v ˉ =uE net , and the only way for v ˉ to be zero is if E net =0.
At equilibrium the net electric field inside a conductor is zero because the conductor polarizes until the electric field inside the conductor due to charges at the surface is equal and opposite to the electric field due to charges in the surroundings.
Learn more about electric field here ;
https://brainly.com/question/11482745
#SPJ11
which term refers to energy due to an object's motion
The term that refers to energy due to an object's motion is called Kinetic energy.
Kinetic energy is the energy of motion of an object. It is directly proportional to its mass and velocity. In simpler terms, the faster an object moves and the more mass it has, the more kinetic energy it possesses.
Mathematically, the formula for kinetic energy can be expressed as KE = 1/2 mv²
Where KE is the kinetic energy, m is the mass of the object and v is its velocity or speed. The unit of kinetic energy is Joules (J). Examples of Kinetic Energy. Some of the common examples of kinetic energy include.
An airplane in flight . A speeding bullet A moving car A falling object A ball that has been thrown or hit A windmill in motion water flowing in a reverse movement of electrons, protons, neutrons, and atoms.
To know more about Kinetic Energy please refer to:
https://brainly.com/question/999862
#SPJ11
This question is about the residence time of carbon within a reservoir. The residence time is equal to the size of the reservoir / the flux in (or out) of the reservoir. If a reservoir has 3800Pg of carbon (1Pg=1*10∧15 g of C ) and a flux out of the reservoir of 3.8Pg / year, how many years is carbon in this reservoir (the residence time)?
O 1
O 10
O 100
O 1000 years
Question 7 1pts
This is another question about the residence time of carbon within a reservoir. The residence time is equal to the size of the reservoir / the flux in (or out) of the reservoir.
If a reservoir has 3800Gt of carbon ( 1Gt=1 billion tons =1*10∧15 g of C ) and a flux out of the reservoir of 3.8Pg/ year, how many years is carbon in this reservoir (the residence time)?
O 1000
O 100
O 10
O 1
Choose the best average residence time for carbon that was incorporated into a tree.
O <1000 years
O >1,000,000 years
O 1 year
O 1Gt
For the first question, the residence time of carbon in a reservoir with 3800 Pg of carbon and flux out of the reservoir of 3.8 Pg/year is approximately 1000 years. For the second question, the residence time of carbon in a reservoir with 3800 Gt of carbon and flux out of the reservoir of 3.8 Pg/year is approximately 100 years. Regarding the average residence time for carbon incorporated into a tree, the best answer would be "O <1000 years," indicating that the carbon stays in the tree for less than 1000 years.
In the first question, to calculate the residence time, we divide the size of the reservoir (3800 Pg) by the flux out of the reservoir (3.8 Pg/year). This gives us a residence time of approximately 1000 years.
In the second question, the size of the reservoir is given in gigatons (3800 Gt), and the flux out of the reservoir is still in petagrams (3.8 Pg/year). We convert the size of the reservoir from gigatons to petagrams by multiplying by 1000, giving us 3800 Pg. Dividing the reservoir size by the flux out of the reservoir (3.8 Pg/year) yields a residence time of approximately 100 years.
Regarding the residence time for carbon incorporated into a tree, it varies depending on factors such as tree species, environmental conditions, and carbon cycling processes. On average, carbon stays in a tree for less than 1000 years. Therefore, the best answer is "O <1000 years."
Learn more about flux at:
https://brainly.com/question/15655691
#SPJ11
What are the composite materials used in the car piston, compare
with their properties
Car pistons are commonly made of composite materials such as aluminum alloy, cast iron, and steel. These materials are chosen for their specific properties that make them suitable for piston applications.
Composite materials used in car pistons are carefully selected to meet the demanding requirements of the engine environment. Aluminum alloy is a popular choice due to its lightweight nature, high strength-to-weight ratio, and excellent thermal conductivity. These properties allow the piston to withstand high temperatures and pressures while minimizing weight, contributing to better fuel efficiency and performance.
Cast iron is another material used in pistons, known for its exceptional wear resistance and thermal stability. It can withstand high temperatures and provides excellent durability under demanding conditions. Cast iron pistons are commonly used in heavy-duty engines and applications where high strength and resistance to wear are crucial.
Steel pistons are employed in high-performance engines where strength, rigidity, and durability are paramount. Steel offers exceptional resistance to thermal and mechanical stresses, making it suitable for extreme operating conditions.
Each composite material used in pistons offers a unique set of properties that cater to specific engine requirements. Factors such as weight, strength, heat dissipation, wear resistance, and thermal stability are considered during material selection to optimize piston performance and reliability.
Learn more about Car pistons
brainly.com/question/26297537
#SPJ11
"during a test crash, a 500 kg car is driven at a constant velocity of 50 mph until it hits a wall without braking. apply all three of newton's laws to this situation."
Newton's first law states that an object will remain in its state of motion unless acted upon by an external force. Newton's second law states that the net force acting on an object is equal to the product of its mass and acceleration.
According to Newton's first law, the car will continue to move at a constant velocity of 50 mph unless acted upon by an external force. When the car hits the wall, a force is exerted on the car, causing it to come to a stop. This force is the result of an interaction described by Newton's third law. As the car collides with the wall, it experiences a deceleration due to the force applied by the wall.
Applying Newton's second law, we can determine the acceleration of the car during the collision. Since the car's velocity is changing from 50 mph to 0 mph, there is a net force acting on the car in the opposite direction of its motion. This force is caused by the collision with the wall and is responsible for decelerating the car.
Newton's third law states that for every action, there is an equal and opposite reaction. In the context of the car crash, these laws can be used to analyze the forces acting on the car.
Learn more about velocity here:
https://brainly.com/question/30559316
#SPJ11
the energy carried by an electromagnetic wave in a vacuum
The energy carried by an electromagnetic wave in a vacuum is related to its frequency by the Planck-Einstein relation.
What is an electromagnetic wave? An electromagnetic wave is a wave that is composed of an electric field and a magnetic field that oscillate perpendicular to each other and to the direction of wave propagation. Electromagnetic waves can travel through a vacuum, such as space, as well as through a medium, such as air or water. The energy carried by an electromagnetic wave is determined by its frequency, which is the number of oscillations per second that the wave undergoes. Higher frequency waves carry more energy than lower frequency waves. The relationship between energy and frequency is given by the Planck-Einstein relation, which states that the energy of a photon (the particle-like entity that electromagnetic waves can be thought of as being composed of) is proportional to its frequency.
Learn more about electromagnetic waves here: https://brainly.com/question/13803241
#SPJ11
Double Mass but Half Speed ? 2 2M Before Collision Two blocks on a horizontal frictionless track head toward each other as shown. One block has twice the mass and half the velocity of the other. toward the left. toward the right. 2V. 1) The velocity of the center of mass of this system before the collision is zero. Submit M Your submissions: Submitted: Sunday, July 3 at 5:27 AM Feedback: Feedback will be available after 10:00 AM on Monday, July 4 Submit (Survey Question) 2) Briefly explain your answer to the previous question. C 3) Suppose the blocks collide elastically. Picking the positive direction to the right, what is the velocity of the bigger block after the collision takes place? +2V +V zero. -V. -2V. Submit Your submissions: B? Submitted: Sunday, July 3 at 5:29 AM Feedback: Feedback will be available after 10:00 AM on Monday, July 4 (Survey Question) 4) Briefly explain your answer to the previous question.
The velocity of the center of mass of this system before the collision is zero because the blocks have equal but opposite velocities. The mass of one block is twice that of the other, but its velocity is half, resulting in equal momentum but in opposite directions. This cancels out the overall velocity of the system.
After the collision, assuming an elastic collision, the velocity of the bigger block will be -V. This is because the smaller block, with twice the velocity, collides with the bigger block, causing a transfer of momentum. The momentum conservation principle states that the total momentum before the collision is equal to the total momentum after the collision. Since the smaller block has a higher velocity, it imparts its momentum to the bigger block, causing it to move in the opposite direction with a velocity of -V.
To know more about velocity please click :-
brainly.com/question/30559316
#SPJ11
A pipe of diameter 17 cm conveying 200 liters/s of water has bend of angle θ = 0⁰ through horizontal plane. Find the resultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15 N/cm2 and 10 N/cm2 respectively.
This resultant force is the sum of the pressure forces at the inlet and outlet of the bend (F1 and F2) and the centrifugal force (Fc) due to the change in direction of the flow.
It's important to note that the centrifugal force acts in the outward radial direction and is balanced by the pressure forces.
The weight of water is neglected in this calculation as it is balanced by the normal force exerted by the walls of the pipe.
the resultant force of 58883.97 N represents the net force exerted on the bend due to the combined effects of pressure and centrifugal forces.
To know more about pressure visit:
https://brainly.com/question/30673967
#SPJ11
QUESTION 2 [6] Two similar round metal rods are used for an earthing system and each of them is buried into a depth of 3 m underground. Determine the distance between the rods if the resistance with two rods found to be 60% of that with one rod. Diameter of each rod is 30 mm.
Diameter of each rod = 30 mm, Burying depth of each rod = 3 m, Resistance with two rods = 60% of that with one rod. Formula used: Resistance of earth for 1 rod, R₁ = ρ × (2 × L)/π × r².
Resistance of earth for 2 rods, R₂ = ρ × (L/d + 1.2) /π × r² Where L = Length of the rodρ = Resistivity of the soil r = radius of the rodd = distance between the rods.
To determine: Distance between the rods
Solution:Radius of each rod, r = Diameter/2 = 30/2 = 15 mm = 0.015 m.
Length of the rod, L = Burying depth of the rod = 3 m.
Resistivity of the soil, ρ is not given, we can assume the value of ρ = 300 Ω-m.
Resistance with one rodR₁ = ρ × (2 × L)/π × r²= 300 × (2 × 3)/π × (0.015)²= 3.77 Ω.
Resistance with two rods, R₂R₂ = ρ × (L/d + 1.2) /π × r².
Let's assume the distance between the rods be 'd'.
Now, R₂ = 0.6 R₁∴ ρ × (L/d + 1.2) /π × r² = 0.6 × 3.77ρ × (L/d + 1.2) /π × r² = 2.262ρ = (2.262 × π × r² × d) / (L/d + 1.2)...... (1).
Now, we can find the value of d from equation (1)
For this, we need the value of ρ.
Now, let's assume the resistivity of soil, ρ = 300 Ω-m.
We have,L/d + 1.2 = 2.262 × π × r² × d /ρL/d + 1.2 = 2.262 × π × (0.015)² × d / 300L/d + 1.2 = 7.14 × 10⁻⁵ dL + 1.2d = 7.14 × 10⁻⁵ d²L = 7.14 × 10⁻⁵ d² - 1.2d...........(2)
From equation (2), we get,3 = 7.14 × 10⁻⁵ d² - 1.2d.
On solving, we get,d = 15.85 m (approx).
Therefore, the distance between the rods is 15.85 m (approx).
Learn more about resistivity here ;
https://brainly.com/question/29427458
#SPJ11
