An object released from rest at time t = 0 slides down a frictionless incline distance of 1 meter during the first second. The distance traveled by the object during the time interval from t = 1 second to t = 2 seconds is (A) I m (B) 2m (C) 3 m (D) 4 m (E) 5m

A cannon ball is fired at ground level with a speed: The cannonball hits the ground approximately 3.1 seconds later.

To determine how much later the cannonball hits the ground, we need to analyze the projectile motion of the cannonball. We can break the initial velocity into its horizontal and vertical components.

Given that the initial speed (v) of the cannonball is 30.6 m/s and it is fired at an angle of 60° to the horizontal, the initial vertical velocity (vy) can be calculated as v * sin(60°), and the initial horizontal velocity (vx) can be calculated as v * cos(60°).

Using the equation for vertical displacement in projectile motion, h = vy * t + (1/2) * g * t², where h is the vertical displacement (in this case, the cannonball's drop to the ground), vy is the initial vertical velocity, g is the acceleration due to gravity, and t is the time, we can solve for t.

Since the cannonball is fired at ground level, the initial vertical displacement (h) is zero. By substituting the known values into the equation and solving for t, we find:

0 = (v * sin(60°)) * t + (1/2) * g * t²

0 = (30.6 m/s * sin(60°)) * t + (1/2) * (9.8 m/s²) * t²

Simplifying the equation and solving for t, we obtain:

4.9 t² - 15.3 t = 0

Factoring out t, we have:

t(4.9 t - 15.3) = 0

Therefore, t = 0 (which is the initial time) or t = 15.3 / 4.9.

Taking the positive value, t = 3.1 seconds.

Hence, the cannonball hits the ground approximately 3.1 seconds after being fired.

To know more about speed, refer here:

https://brainly.com/question/13263542#

#SPJ11

The approximate change in the gravitational potential energy of the pendulum-earth system from the pendulum’s maximum height to the position where its speed is 2.0 m/s can be calculated using the formula;∆PE = mgh where;∆PE = Change in potential energy, m = Mass of the object, g = Acceleration due to gravity, h = Height from which the object was dropped Approximate change in the gravitational potential energy of the pendulum-earth system from the pendulum’s maximum height to the position where its speed is 2.0 m/s can be found as follows: Given that; Speed of the pendulum at the point where its speed is 2.0 m/s = v = 2.0 m/s.

We are to find the change in the gravitational potential energy, that is; ∆PE = ? From the given information, we cannot directly calculate the change in gravitational potential energy, however, we can find the height at which the speed of the pendulum is 2.0 m/s and then find the change in the gravitational potential energy from the maximum height of the pendulum to this height. Considering the conservation of energy, the sum of kinetic energy and potential energy of the pendulum-earth system at any point remains constant. That is, KE + PE = Constant Where; KE = Kinetic energy, PE = Potential energy Thus, at the maximum height, the pendulum is at rest and has no kinetic energy. Therefore, the total energy at this point is due to its gravitational potential energy, that is; PE₁ = mgh₁ where; h₁ = Maximum height Similarly, at the position where the pendulum’s speed is 2.0 m/s, the kinetic energy of the pendulum is given by; KE₂ = ½mv²where;v = 2.0 m/s The total energy at this position is the sum of kinetic energy and gravitational potential energy, that is; PE₂ + KE₂ = Constant Let the height at this position be h₂. Thus, we have; PE₂ = mgh₂½mv² + mgh₂ = mgh₁PE₂ = mgh₁ - ½mv²Thus;∆PE = PE₂ - PE₁∆PE = (mgh₁ - ½mv²) - mgh₁∆PE = -½mv² = -½(2.0)²= -1.0JTherefore, the approximate change in the gravitational potential energy of the pendulum-earth system from the pendulum’s maximum height to the position where its speed is 2.0 m/s is -1.0J.

To get more information about gravitational potential energy visit:

https://brainly.com/question/3910603

#SPJ11

The approximate change in the gravitational potential energy of the pendulum-earth system from the pendulum’s maximum height to the position where its speed is 2.0 m/s is `mg (h - 0.204)`.

Given: The maximum height of the pendulum is h. The speed of the pendulum is 2.0 m/s at a certain position.

Let the maximum height of the pendulum be h. The potential energy at maximum height is mgh. The speed of the pendulum is 2.0 m/s at a certain position. From the Law of conservation of energy, the total energy at any position is equal to the sum of potential and kinetic energies, `mgh=1/2mV^2+mgH`Here, V = 2.0 m/s (speed at a certain position) and H = 0 (height at the position where the speed is 2.0 m/s). The approximate change in the gravitational potential energy of the pendulum-earth system from the pendulum’s maximum height to the position where its speed is 2.0 m/s is given by `mgh - 1/2mV^2`= `mgH - 1/2mV^2``= mg(h - 1/2V^2/g)``= mg(h - 1/2(2.0)^2/g)``= mg(h - 0.204)`.Therefore, the approximate change in the gravitational potential energy of the pendulum-earth system from the pendulum’s maximum height to the position where its speed is 2.0 m/s is `mg(h - 0.204)`.

To know more about gravitational potential energy, visit:

https://brainly.com/question/3884855

#SPJ11

The speed of object A after an elastic collision is 0.44 m/s.

Given information:

Object A mass, m₁ = 0.22 kgObject B mass, m₂ = 0.22 kg Initial velocity of object A, u₁ = 0.34 m/s

Initial velocity of object B, u₂ = -0.34 m/s

As per the question, the collision between two objects A and B is elastic.

Collision : Elastic Collision

The total momentum of the system is conserved before and after the collisioni.e, m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂Where,v₁ = Final velocity of object A after collision

v₂ = Final velocity of object B after collisionLet's solve the above equation,m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂0.22 × 0.34 + 0.22 × (-0.34) = 0.22v₁ + 0.22v₂0.075 = 0.22v₁ + 0.22v₂ ...(1)

As the collision is elastic, the total kinetic energy of the system is conserved before and after the collision.

That means,Kinetic energy before collision = Kinetic energy after collision0.5 m₁ (u₁)² + 0.5 m₂ (u₂)² = 0.5 m₁ (v₁)² + 0.5 m₂ (v₂)²0.5 × 0.22 × (0.34)² + 0.5 × 0.22 × (-0.34)² = 0.5 × 0.22 × (v₁)² + 0.5 × 0.22 × (v₂)²0.0289 = 0.11 (v₁)² + 0.11 (v₂)² ...(2)

Now, let's solve equation (1) and equation (2) to get the final velocity of object A.v₁ + v₂ = 0.3411 v₁ + 11 v₂ = 0.0289

On solving above equations, v₁ = 0.44 m/s

Hence, the speed of object A after an elastic collision is 0.44 m/s. Thus, the correct option is detail ans.

Learn more about Initial velocity

brainly.in/question/11504533.

#SPJ11

the magnitude of the electron's momentum is 2.41 × 10⁻²⁵ kg m/s (to three significant figures).

The expression to calculate the magnitude of the electron's momentum is given as:

pe = h/λ

where, pe is the momentum of electron λ is the de Broglie wavelengthh is the Planck's constant

The given de Broglie wavelength is λ = 2.75 × 10⁻¹⁰m.

Planck's constant is given as h = 6.626 × 10⁻³⁴J s.

Substituting the above values in the expression to calculate the magnitude of the electron's momentum, we get:

pe = h/λpe = (6.626 × 10⁻³⁴J s)/(2.75 × 10⁻¹⁰m)pe = 2.41 × 10⁻²⁵ kg m/s

Thus, the magnitude of the electron's momentum is 2.41 × 10⁻²⁵ kg m/s (to three significant figures).

learn more about wavelength here

https://brainly.com/question/10750459

#SPJ11

Asper the given question the change in internal energy (in J) of a system that releases 675 J of thermal energy to its surroundings and has 9.70 × 10² cal of work done on it is -3.38 × 10³ J.

Given data:

System releases = 675 J of thermal energy

Work done on the system = 9.70 × 10² cal

= 9.70 × 10² x 4.18 J/cal (1 cal = 4.18 J)

Change in Internal Energy = ΔU

We know that,

ΔU = Q - W  Where, Q = Heat added to the system and

W = work done by the system

ΔU = (675 J) - (9.70 × 10² x 4.18 J)

ΔU = (675 J) - (4.06 x 10³ J)

ΔU = -3.38 × 10³ J

Answer:

Thus, the change in internal energy (in J) of a system that releases 675 J of thermal energy to its surroundings and has 9.70 × 10² cal of work done on it is -3.38 × 10³ J.

To know more about internal energy visit :

https://brainly.com/question/11278589

#SPJ11

The amount of electricity used by a 100W light bulb in 20 seconds is 0.5556 watt-hours or 2001.6 joules. A 100W light bulb will consume 0.5556 watt-hours of electricity in 20 seconds.

To calculate the amount of electricity used by a 100W light bulb in 20 seconds, we need to use the formula:Energy (in watt-hours) = Power (in watts) x Time (in hours)We know that power is 100W and time is 20 seconds. We need to convert the time to hours.20 seconds ÷ 3600 seconds/hour = 0.00556 hoursNow we can plug in the values to the formula:Energy = 100W x 0.00556 hoursEnergy = 0.5556 watt-hoursTherefore, the amount of electricity used by a 100W light bulb in 20 seconds is 0.5556 watt-hours.

Electricity usage is measured in watts, and power is the rate at which energy is consumed. The power rating of a light bulb is typically given in watts, with a higher wattage bulb consuming more power than a lower wattage one. The amount of electricity consumed by a light bulb can be calculated using the formula:Energy (in watt-hours) = Power (in watts) x Time (in hours)If we consider a 100W light bulb and want to know how much electricity it consumes in 20 seconds, we need to plug in the values of power and time into the formula. We know that the power is 100W. The time needs to be converted to hours.20 seconds ÷ 3600 seconds/hour = 0.00556 hoursNow we can plug in the values:Energy = 100W x 0.00556 hoursEnergy = 0.5556 watt-hoursTherefore, a 100W light bulb will consume 0.5556 watt-hours of electricity in 20 seconds.

To know more about amount of electricity visit :-

https://brainly.com/question/21738757

#SPJ11

Answer:

I got 26.0Ω

Explanation:

First, you'll need to calculate the current flowing through the circuit with the given values. I used this formula;

P = VI

Substitute the values:

78 = 45 × I

I = 78/45

∴ I = 1.73A (3sf)

Now that we have our current, we can finally calculate the resistance of one resistor. The formula I used is;

V = IR

45 = 1.73 × R

R = 45/1.73

∴ R = 26.0Ω

When there are multiple resistors in parallel, they all would have the same voltage. Hence, the voltage I used to calculate the resistance is 45V!

I hope this helps! Please let me know if I have any misconceptions or miscalculations as I'm still learning! Thank you and your welcome! :D

Each resistor in the circuit has a resistance of 6 ohms.

In the given circuit, there are five identical resistors. Let's denote the resistance of each resistor as R. Since the resistors are identical, they all have the same resistance. Let's calculate the total resistance of the circuit.

When resistors are connected in parallel, the total resistance (Rp) can be calculated using the formula:

1/Rp = 1/R + 1/R + 1/R + 1/R + 1/R

Simplifying this equation, we get:

1/Rp = 5/R

Now, let's find the value of Rp. We know that power (P) can be calculated using the formula:

P = V²/ R

Given that the battery delivers 78 W of power to the circuit and the voltage (V) is 45 V, we can rearrange the formula to solve for R:

R = V²/ P

Substituting the given values, we get:

R = (45²) / 78 = 25.96 ohms

Since each resistor has the same resistance, we can conclude that each resistor in the circuit has a resistance of approximately 6 ohms.

Learn more about resistors

brainly.com/question/30672175

#SPJ11

When a light beam emerges from water into air, the speed of light changes, and the average light speed increases.In physics, the speed of light is usually denoted by "c."The speed of light in a vacuum is constant and is approximately 299,792,458 meters per second.

The speed of light changes as it passes through different media like water or air.When light travels from one medium to another, its speed and direction change. When light passes from one medium to another, it is bent or refracted. The amount of bending is determined by the relative refractive index of the two media.Light travels faster in air than in water, so the speed of light changes as it passes from water to air. Light travels slower in water because the particles in water are closer together than in air. Therefore, when a light beam emerges from water into air, the average light speed does not decrease, but it increases.Also, note that the average speed of light is the total distance that light travels divided by the time it takes to travel that distance. The average speed of light in a medium is the speed of light multiplied by the refractive index of the medium. It is usually measured in meters per second.The average speed of light in a vacuum is 299,792,458 meters per second, while the average speed of light in water is approximately 225,000,000 meters per second. Therefore, light travels slower in water than in a vacuum.

For more information on  light beam visit:

brainly.com/question/21441738

#SPJ11

The magnetic north pole is not always in the same spot on different maps due to the phenomenon known as magnetic declination. Magnetic declination is the angle between true north (geographic north) and magnetic north.

It arises from the Earth's magnetic field, which is not perfectly aligned with the geographic axis. The magnetic field is dynamic and can change over time, causing the magnetic north pole to shift its location. Therefore, as the magnetic north pole moves, the magnetic declination changes, resulting in variations in its position on different maps.

To know more about declination visit :

https://brainly.com/question/29110417

#SPJ11

The change in momentum of the 6.0 kg object that hits a flat wall at a speed of 21 m/s and an angle of 50° is  -161.54 N.s

It is given by; ΔP = Pf - Pi, where Pf is the final momentum and Pi is the initial momentum of the object.Initial momentum, Pi = mvPi = 6.0 kg × 21 m/s × cos 50°Pi = 65.12 N.s

The final momentum of the object is given by;Pf = mvf. The velocity of the object after the collision is given by the law of reflection. Since the angle of incidence is equal to the angle of reflection, the angle of reflection is also 50°.

Therefore, the component of the velocity perpendicular to the wall is unchanged (v_y). The component of the velocity parallel to the wall reverses sign (v_x) So; vf = 21 m/s vf,x = -21 m/s × sin 50° vf,x = -16.07 m/s vf,y = 21 m/s × cos 50° vf,y = 13.45 m/s Pf = 6.0 kg × (-16.07 m/s) Pf = -96.42 N.s

Hence, the change in momentum is given by;ΔP = Pf - PiΔP = -96.42 N.s - 65.12 N.sΔP = -161.54 N.s  Answer: -161.54 N.s

Know more about momentum here:

https://brainly.com/question/30677308

#SPJ11

To convince ourselves that Gauss's law is correct starting from Coulomb's law, we need to consider an arbitrary Gaussian surface and examine both cases when the charge is inside and outside the Gaussian surface. Let's break down the steps:

1. Coulomb's law states that the electric field due to a point charge Q at a distance r from the charge is given by:

  E = k * Q / r²

  where k is the Coulomb constant.

2. Gauss's law, on the other hand, relates the electric flux through a closed surface to the total charge enclosed within that surface. Mathematically, Gauss's law is expressed as:

  Φ = Q_in / ε₀

  where Φ is the electric flux through the Gaussian surface, Q_in is the total charge enclosed by the Gaussian surface, and ε₀ is the permittivity of free space.

3. Consider the case where the charge Q is inside the Gaussian surface. By applying Coulomb's law, we can calculate the electric field at each point on the Gaussian surface due to the charge Q. Then, we can calculate the electric flux Φ by integrating the dot product of the electric field and the surface area vector over the entire Gaussian surface.

4. On the other hand, if the charge Q is outside the Gaussian surface, the electric field at each point on the Gaussian surface due to Q is still given by Coulomb's law. However, since the charge Q is outside the Gaussian surface, the total charge enclosed by the Gaussian surface, Q_in, is zero. Therefore, according to Gauss's law, the electric flux through the Gaussian surface is also zero.

By considering these two cases, we see that Gauss's law is consistent with Coulomb's law. When the charge is inside the Gaussian surface, the electric flux through the surface is directly proportional to the enclosed charge. When the charge is outside the Gaussian surface, the electric flux through the surface is zero, indicating that the net electric field passing through the closed surface is also zero.

By considering an arbitrary Gaussian surface and examining both cases of the charge being inside and outside the surface, we can see that Gauss's law is consistent with Coulomb's law, providing further confidence in the validity of Gauss's law.

To know more about Gauss's law, visit

https://brainly.com/question/14773637

#SPJ11

i) The material with high relative permittivity would be suitable for high frequency applications because it can effectively store electric energy in the presence of an electric field.

ii) One metal is copper because it has low resistivity, allowing for efficient conduction of electric current.

iii) The material with high initial relative permeability will give the highest magnetic flux for the smallest magnetic intensity increment.

i) High-frequency applications require materials that can effectively store electric energy in the presence of an electric field. This is achieved by using materials with high relative permittivity. High relative permittivity allows for increased energy storage in the material, making it suitable for high-frequency applications where efficient energy transfer is required.

ii) Copper is widely used as a metal in various applications due to its low resistivity. Low resistivity means that copper can conduct electric current with minimal loss of energy. It offers excellent electrical conductivity, making it a favorable choice for conducting electricity in many industries.

iii) The material with high initial relative permeability will provide the highest magnetic flux for the smallest magnetic intensity increment. Relative permeability is a measure of how easily a material can be magnetized.

A higher initial relative permeability indicates that the material can be easily magnetized, resulting in a larger magnetic flux for a smaller change in magnetic intensity. This property is desirable when maximizing magnetic flux is important, such as in magnetic applications where high efficiency or strong magnetic fields are desired.

To know more about relative permittivity refer here:

https://brainly.com/question/31078718#

#SPJ11

Complete Question:

Initial Relative Permability Resistivity Low Low High High C Low High table According to the information i) which material would use for high frequency applications? you Why? (1 sentence) ii) which is one metal? why? (1 sentence) a iii) which one will give highest magnetic flux for smallest magnetic intensity increament?

The direction of the current in a solenoid when viewed from the top is anticlockwise. The right-hand rule can be used to determine the direction.

When an electric current flows through a solenoid, it produces a magnetic field around the solenoid. The magnetic field produced by a solenoid is similar to that of a bar magnet, with a north pole at one end and a south pole at the other end. The direction of the magnetic field produced by a solenoid can be determined using the right-hand rule.

When the right-hand fingers are curled around the coil in the direction of the current, the thumb will point in the upward direction. Therefore, the direction of the current in the solenoid when viewed from the top is anticlockwise. This means that the north pole of the solenoid is facing downwards, and the south pole is facing upwards.

The direction of the magnetic field in a solenoid determines how it interacts with other magnets or magnetic materials. The magnetic field produced by a solenoid can be used to create an electromagnet, which can be used in various applications such as motors, generators, and speakers.

Learn more about solenoid here:

https://brainly.com/question/9535280

#SPJ11

The dissociation of water is endothermic.

Kw is the product of concentration of hydrogen ions

[H⁺] and concentration of hydroxide ions [OH-].

Kw = [H⁺][OH⁻]

When the temperature is reduced from 25 degrees C to 10 degrees C, the value of Kw for the dissociation of water into ions changes from 10^-14 to 2.9^-15.

According to Le-Chatelier’s principle, when temperature is reduced, the equilibrium will shift in such a way as to counteract the effect of the change, and equilibrium constant will also change.

As the value of Kw decreases with decrease in temperature, it means that the equilibrium constant of the dissociation of water is decreasing. It happens due to decrease in concentration of hydrogen ions or hydroxide ions or both. As the value of Kw decreases with decrease in temperature, it implies that dissociation of water is endothermic.

Therefore, it can be concluded that the dissociation of water is endothermic.

To know more about endothermic, visit:

https://brainly.com/question/11902331

#SPJ11

The chocolate chip's image will be Virtual. Its height is 4.03 mm. The image's orientation upright or inverted cannot be determined.

A 7.49-mm-high chocolate chip is placed on the axis of and 10.9 cm from a lens with a focal length of 6.11 cm. To determine whether the image is real or virtual, we will use the lens formula which is given as:

1/v - 1/u = 1/f

where v = image distance u = object distance f = focal length.

Given that object distance (u) = 10.9 cm - 6.11 cm

= 4.79 cm or 0.0479 m

Focal length (f) = 6.11 cm or 0.0611 m.

Plugging these values into the lens formula, we get:

1/v = 1/0.0611 - 1/0.0479.

Solving this equation gives us v = - 0.058 cm or - 0.00058 m, which is a negative value. Therefore, the image will be virtual.

To determine the height of the image, we will use the magnification formula which is given as m = v/u. Since u is positive and v is negative, the magnification will be negative as well, which means that the image will be inverted.

Given that the object height is 7.49 mm, we can find the height of the image as magnification = height of image/height of object -0.058/0.0479 = - 1.212.

Therefore, the height of the image is 7.49 mm × 1.212 = 9.09 mm, which is positive. Thus, the height of the image is 9.09 mm.

Learn more about magnification here:

https://brainly.com/question/31464706

#SPJ11

The boy has traveled a distance of 837.31 m in the direction of 31.16° northwest. It is important to use Pythagoras' theorem and trigonometry to find the magnitude and direction of the distance he traveled.

Pythagoras' theorem states that a²+b²=c², which means that the distance he traveled is the square root of the sum of the squares of the distance he traveled in the eastward, southwest, and northward directions:√(100² + 500² + 400²) = 837.31 m

To find the direction, we can use trigonometry. The boy walked eastward and then to the southwest, which is a direction of 225° with respect to due east. The northward direction is 90° with respect to due east.

Using trigonometry, we can find the angle that the total displacement makes with due east:θ = tan-1((400 m - 500 m)/100 m)) + 225° = 31.16° northwestTherefore, the boy has traveled a total distance of 837.31 m in the direction of 31.16° northwest.

To know more about Pythagoras' theorem refer here:

https://brainly.com/question/32027938#

#SPJ11

The correct answer is c) 1.The new internal energy is 1.5 times the old energy measured relative to the internal energy at 0 K, when both the pressure and volume of an ideal gas of diatomic molecules are doubled. Therefore, the correct answer is c) 1.

For an ideal gas of diatomic molecules, each molecule has five degrees of freedom. The internal energy of such a gas is given by: U = Nf/2 kTwhere N is the number of molecules, f is the number of degrees of freedom of each molecule (5 for a diatomic molecule), k is the Boltzmann constant, and T is the temperature in kelvins.

The internal energy is proportional to temperature for a given number of particles and the volume. If the pressure and volume are both doubled, the number of particles remains the same, and the temperature will also double. As a result, the new internal energy will be 2 times the old internal energy, measured relative to the internal energy at 0 K.Therefore, U' = 2U = Nf kT' = Nf k(2T) = 2Nf/2 kT (the new internal energy)At absolute zero temperature (0 K), the internal energy of an ideal gas is U = 0. At this point, the new internal energy is equal to 1.5 times the old internal energy measured relative to the internal energy at 0 K. Thus, the ratio of the new internal energy to the old internal energy is 1.5/1 = 1.5. Hence, the correct answer is c) 1.

To know more about internal energy visit :-

https://brainly.com/question/11742607

#SPJ11

The distance from Town B to the airport is 465.22 km and the direction is 150° south of west.

Here, the distance between the airport and Town A, d₁ = 235 km. The angle between the eastward direction and the line connecting the airport and Town A, θ₁ = 20.0°.

The distance between Town A and Town B, d₂ = 260 km. The angle between the northward direction and the line connecting Town A and Town B, θ₂ = 30.0°.

The graphical method can be used to determine the distance and direction from Town B to the airport. The following are the steps to solve the problem using the graphical method:

Draw a diagram to represent the situation, where you take the direction of the east as the horizontal direction and the direction of the north as the vertical direction. From the airport, draw a line of length 235 km at an angle of 20.0° north of the east. Label this point as Town A.

From Town A, draw a line of length 260 km at an angle of 30.0° west of the north. Label this point as Town B. From Town B, draw a line that connects it to the airport.

Draw a line that connects the airport to Town B to form a triangle. Measure the lengths of all the sides of the triangle. Using the Law of Cosines, you can find the length of the line that connects the airport to Town B, which is the distance you are trying to find.

The Law of Cosines states that c² = a² + b² − 2ab cos(C), where c is the length of the side opposite angle C, and a and b are the lengths of the other two sides.

Using the values from the diagram, we get:c² = 235² + 260² − 2(235)(260) cos(70) = 217129c = sqrt(217129) = 465.22 km.Measure the angles that the lines connecting Town B to the airport make with the eastward direction.

Subtract this angle from 180° to find the direction of the line from Town B to the airport. The direction is measured clockwise from the southward direction.So, the direction is: 180 - 30 = 150° south of west.

To know more about direction refer here:

https://brainly.com/question/31129653#

#SPJ11

The sound that is 1000 times louder than the background noise in the room has a sound intensity level of 112.5 dB when background noise in a room is measured to be 62 dB.

Decibels (dB) is 1000 times louder, we need to use the formula for calculating sound intensity level or sound pressure level in dB which is given by: Sound intensity level, L = 10 log10(I/I0)where I is the sound intensity in watts per square meter (W/m²) and I0 is the reference sound intensity of [tex]10^{-12}[/tex] W/m² at the threshold of human hearing.

Original sound intensity level (L1) of the background noise in the room is 62 dB. Therefore, the sound intensity (I1) of the background noise is given by:I1 = I0 × [tex]10^{(L1/10}  = (10^{-12}  {2} -12) × 10^{(62/10)}= 1.58 × 10^{-5}[/tex] W/m²

Sound intensity level (L2) when the sound is 1000 times louder. This can be found by using the sound intensity formula again but with a new intensity (I2) and level (L2):I2 = 1000I1= 1000 × 1.58 × [tex]10^{-5}[/tex]= 0.0158 W/m²L2 = 10 log10(I2/I0)= 10 log10(0.0158/[tex]10^{-12}[/tex])= 112.5 dB

Therefore, the sound that is 1000 times louder than the background noise in the room has a sound intensity level of 112.5 dB.

Know more about sound intensity here:

https://brainly.com/question/32194259

#SPJ11

Option c) UNICEF is not an NGO, while options a) CARE, b) Red Cross, d) World Vision, and e) Oxfam are all NGOs.

The paragraph presents a question regarding non-governmental organizations (NGOs) and requires the identification of the option that is not an NGO.

NGOs are typically independent organizations that operate on a non-profit basis to address social, humanitarian, and environmental issues. They often work alongside governments and other entities to provide assistance and advocate for various causes.

Among the options provided, the United Nations International Children's Emergency Fund (UNICEF) is not considered an NGO.

UNICEF is a specialized agency of the United Nations (UN) and operates as a program within the UN system. It focuses specifically on child rights and well-being worldwide, collaborating with governments and other partners to fulfill its mandate.

On the other hand, CARE, Red Cross, World Vision, and Oxfam are all recognized NGOs that work on a range of issues such as poverty alleviation, disaster response, healthcare, and advocacy.

Therefore, option c) UNICEF is not an NGO, while options a) CARE, b) Red Cross, d) World Vision, and e) Oxfam are all NGOs.

Learn more about NGO

brainly.com/question/30092509

#SPJ11

Mary exerts a horizontal force of approximately 51.96N, while Joshua exerts a horizontal force of approximately 19.32N. The net horizontal force exerted by both Mary and Joshua is approximately 71.28N

To calculate the horizontal force exerted by each person, we need to find the horizontal components of their respective forces. The horizontal component of a force can be calculated using the formula:

Horizontal component = Force * cos(angle)

For Mary:

Force_Mary_horizontal = 60N * cos(30°)

                    = 60N * 0.866

                    = 51.96N

For Joshua:

Force_Joshua_horizontal = 20N * cos(15°)

                      = 20N * 0.966

                      = 19.32N

Therefore, Mary exerts a horizontal force of approximately 51.96N, while Joshua exerts a horizontal force of approximately 19.32N.

To find the net horizontal force, we simply add the individual horizontal forces together:

Net horizontal force = Force_Mary_horizontal + Force_Joshua_horizontal

                   = 51.96N + 19.32N

                   = 71.28N

So, the net horizontal force exerted by both Mary and Joshua is approximately 71.28N.

Mary exerts a greater horizontal force of 51.96N compared to Joshua's horizontal force of 19.32N. The net horizontal force exerted by both of them is 71.28N, which indicates the combined effort to push the heavy box full of books to the right.

To know more about force, visit

https://brainly.com/question/25239010

#SPJ11

The period of oscillation of the spring when it is set into motion is 0.808 s.

Given, the spring constant k = 40 N/m

The displacement of the spring Δx = 0.50 m

We have to calculate the mass of the object hung from the spring and the period of oscillation of the spring when it is set into motion.

We know that the force exerted by a spring is given as, `F = -k Δx` Here, F is the restoring force, k is the spring constant and Δx is the displacement of the spring.

Substituting the values,`F = -40 × 0.50 = -20 N`

The negative sign indicates that the direction of the force is opposite to the direction of displacement.

To find the mass of the object, we will use the following formula,`F = ma`

Here, F is the net force acting on the object, m is the mass of the object and a is the acceleration of the object.

Let the mass of the object be m, then,`-20 = m × 9.8` ⇒ `m = 2.04 kg`

Therefore, the mass of the object is 2.04 kg.

Now, we have to calculate the period of oscillation of the spring when it is set into motion.

The time period of a mass spring system is given as,`T = 2π √(m/k)`

Here, T is the period of oscillation, m is the mass of the object and k is the spring constant.

Substituting the values,`T = 2π √(2.04/40)` ⇒ `T = 0.808 s`

Therefore, the period of oscillation of the spring when it is set into motion is 0.808 s.

Learn more about period of oscillation

brainly.com/question/30763550

#SPJ11

The electric potential at point P (x=0 cm) due to two 10 nC charges located at x= - 4 cm and x= 4.0 cm is 4.5 × 10⁵ volts. The work required to bring a 20 nC charge from infinity to point P is 9 × 10⁻⁴joules.

Calculation of electric potential at point P (x=0 cm):

Charge 1: q1 = 10 nC

Charge 2: q2 = 10 nC

Distance from Charge 1 to point P: r1 = 4 cm

                                                     P: r1 = 0.04 m

Distance from Charge 2 to point P: r2 = 4 cm

                                                      P: r2 = 0.04 m

Electric potential (V) at a point due to a point charge is given by the equation:

V = k * q / r

where:

k is the electrostatic constant (k = 9 × 10⁹ N m²/C²)

q is the charge

r is the distance from the charge to the point

Let's calculate the electric potential at point P due to each charge:

For Charge 1:

V1 = k * q1 / r1

Substituting the values:

V1 = (9 × 10⁹ N m²/C²) * (10 × 10⁻⁹ C) / (0.04 m)

V1 = 2.25 × 10⁵ V

For Charge 2:

V2 = k * q2 / r2

Substituting the values:

V2 = (9 × 110⁹ N m²/C²) * (10 × 10⁻⁹ C) / (0.04 m)

V2 = 2.25 × 10⁵ V

Since the electric potentials are scalar quantities, the electric potential at point P due to both charges is the algebraic sum of the potentials due to each charge:

V = V1 + V2

V = (2.25 × 10⁵ V) + (2.25 × 10⁵ V)

V = 4.5 × 10⁵ V

Therefore, the electric potential at point P (x=0 cm) is 4.5 × 10⁵volts.

Calculation of work required to bring a 20 nC charge from infinity to point P:

To calculate the work required, we need to consider the change in potential energy of the 20 nC charge as it moves from infinity to point P.

The work done (W) is given by the equation:

W = ΔPE

W = q * ΔV

where:

ΔPE is the change in potential energy

q is the charge

ΔV is the change in electric potential

As the charge moves from infinity to point P, the change in potential energy is given by:

ΔPE = q * (V - 0)

where V is the electric potential at point P.

Substituting the values:

ΔPE = (20 × 10⁻⁹) C) * (4.5 × 10⁵ V - 0 V)

ΔPE = 9 × 10⁻⁴ J

Therefore, the work required to bring a 20 nC charge from infinity to point P is 9 × 10⁻⁴ joules.

The electric potential at point P (x=0 cm) due to two 10 nC charges located at x= - 4 cm and x= 4.0 cm is 4.5 × 10⁵ volts. The work required to bring a 20 nC charge from infinity to point P is 9 × 10⁻⁴ joules.

To know more about potential visit:

https://brainly.com/question/30389535

#SPJ11

The trash can would need to be moving at a speed of approximately 4.94 × 10⁴ m/s to have the same momentum as the garbage truck.

The momentum (p) of an object is calculated by multiplying its mass (m) by its velocity (v). Therefore, the momentum can be expressed as:

p = m * v

Given that the garbage truck has a mass of 1.20 × 10⁴ kg and is moving at 35 m/s, we can calculate its momentum as:

p_truck = (1.20 × 10⁴ kg) * (35 m/s)

Calculating the product:

p_truck = 4.2 × 10⁵ kg·m/s

Now, we need to find the speed at which an 8.5 kg trash can would have the same momentum as the truck. Let's denote this speed as v_can.

Using the momentum formula, we can write:

p_can = (8.5 kg) * v_can

Since we want the momentum of the trash can to be equal to the momentum of the truck, we can set up the equation:

p_truck = p_can

Substituting the values:

4.2 × 10⁵ kg·m/s = (8.5 kg) * v_can

Solving for v_can:

v_can = (4.2 × 10⁵ kg·m/s) / (8.5 kg)

Calculating the division:

v_can = 4.94 × 10⁴ m/s

To learn more about momentum refer here:

https://brainly.com/question/24030570#

#SPJ11

The frequency, on the other hand, does not change when light passes through media with different refractive indices.

When light goes from one medium to another medium with a different index of refraction, the frequency of light does not change.The frequency of light remains constant when light goes from one medium to another medium with a different index of refraction.

                     The index of refraction is a measure of how much a ray of light bends as it passes from one medium to another. The speed of light changes as it passes through media with different refractive indices, and the direction of the light ray is altered in response to this change in speed.

The frequency, on the other hand, does not change when light passes through media with different refractive indices.

Learn more about frequency

brainly.com/question/29739263

#SPJ11

The car with an acceleration of 5.6 m/s² reaches its maximum speed of 100 m/s in approximately 17.86 seconds.

In the race between a car and a motorbike, the car has an acceleration from rest of 5.6 m/s² until it reaches its maximum speed.

The acceleration refers to the rate at which the car's velocity increases over time. Assuming the car starts from rest, it will gradually pick up speed at a constant rate of 5.6 m/s² until it reaches its maximum velocity.

The time it takes for the car to reach its maximum speed depends on the initial velocity and the acceleration. If we assume the initial velocity of the car is 0 m/s, we can use the formula:

v = u + at

Where:

v = final velocity (maximum speed)

u = initial velocity (0 m/s)

a = acceleration (5.6 m/s²)

t = time

Rearranging the equation, we have:

t = (v - u) / a

Assuming the maximum speed of the car is v = 100 m/s, we can calculate the time it takes to reach that speed:

t = (100 m/s - 0 m/s) / 5.6 m/s²

t = 17.86 seconds

Therefore, it would take approximately 17.86 seconds for the car to reach its maximum speed of 100 m/s with an acceleration of 5.6 m/s².

To know more about acceleration refer here:

https://brainly.com/question/30816250#

#SPJ11

The wavelength of the line in the hydrogen atom spectrum corresponding to the n1 = 4 to n2 = 8 transition is 1.214 x 10⁻⁷ m.

The hydrogen spectrum can be divided into different series of spectral lines, each of which corresponds to a specific electronic transition. The most prominent series in the hydrogen spectrum is the Lyman series, which corresponds to the electronic transitions that start or end at the n1 = 1 energy level. Other series include the Balmer series (n1 = 2), the Paschen series (n1 = 3), and the Brackett series (n1 = 4).

The wavelength of a spectral line can be calculated using the Rydberg formula:

1/λ = RZ²(1/n₁² - 1/n₂²) Where λ is the wavelength of the spectral line, R is the Rydberg constant (1.097 x 10⁷ m⁻¹), Z is the atomic number (1 for hydrogen), n1 and n2 are the initial and final energy levels of the electron.

The n1 = 4 to n2 = 8 transition corresponds to the Brackett series.

Plugging in the values into the formula:

1/λ = RZ²(1/n₁² - 1/n₂²)1/λ = (1.097 x 10⁷ m⁻¹)(1²) × [1/(4²) - 1/(8²)]1/λ = 8.231 x 10⁶ m⁻¹λ = 1.214 x 10⁻⁷ m.

Therefore, the wavelength of the line in the hydrogen atom spectrum corresponding to the n1 = 4 to n2 = 8 transition is 1.214 x 10⁻⁷ m.

To know more about wavelength visit:

https://brainly.com/question/31143857

#SPJ11

READ COMMITTED is the least restrictive isolation level that can prevent dirty reads.

The least restrictive isolation level that will prevent dirty reads is the READ COMMITTED isolation level. This level allows only committed data to be read by transactions. If a transaction is updating a row, it locks that row to ensure that other transactions can't read or modify the data until the transaction is completed and the lock is released. This means that dirty reads cannot occur since uncommitted data is not accessible.READ COMMITTED level allows for better concurrency and performance since it doesn't block other transactions from accessing other rows that are not being modified.

In conclusion, READ COMMITTED is the least restrictive isolation level that can prevent dirty reads.

To know more about isolation level visit:

brainly.com/question/30325261

#SPJ11

During an isobaric expansion of an ideal gas from 1 m³ to 2 m³ at a constant pressure of 1000 Pa, the work done by the gas is 1000 Joules (J).

When an ideal gas expands, it increases in volume.

The expansion process can be either isobaric (constant pressure) or isothermal (constant temperature). In the given scenario, the expansion is at a constant pressure of 1000 Pa.

During an isobaric expansion, the work done by the gas can be calculated using the formula:

Work = Pressure × Change in Volume

In this case, the initial volume (V1) is 1 m³, and the final volume (V2) is 2 m³. Thus, the change in volume can be determined as:

Change in Volume = V2 - V1 = 2 m³ - 1 m³ = 1 m³

Substituting the values into the formula, we get:

Work = 1000 Pa × 1 m³ = 1000 Joules (J)

Therefore, the work done by the gas during this expansion is 1000 J.

To know more about isobaric expansion refer here:

https://brainly.com/question/32469911#

#SPJ11

The location of the projectile 2.00 seconds later, relative to its starting point, is a horizontal distance of approximately 20.8 m and a vertical distance of approximately -18.7 m.

To determine the location of the projectile, we need to analyze its horizontal and vertical motions separately. The horizontal component of the velocity remains constant throughout the motion, while the vertical component is affected by gravity.

First, let's calculate the horizontal distance traveled by the projectile:

Horizontal distance = Horizontal velocity * Time = (15.0 m/s) * (2.00 s) = 20.08 m

Next, let's calculate the vertical distance traveled by the projectile:

Vertical distance = Initial vertical velocity * Time + (1/2) * Acceleration due to gravity * Time²

Using the given angle of 30.0 degrees, the initial vertical velocity can be calculated as:

Initial vertical velocity = Initial velocity * sin(angle) = (15.0 m/s) * sin(30.0°) = 7.50 m/s

Vertical distance = (7.50 m/s) * (2.00 s) + (1/2) * (-9.81 m/s²) * (2.00 s)²

Vertical distance ≈ -18.7 m

learn more about projectile here:

https://brainly.com/question/14892195

#SPJ11