calculate the magnitude of his average acceleration during the first part of his motion. express your answer in multiples of g by taking its ratio to 9.80 m/s2.

The concentration of salt in water affects the specific heat capacity by changing the thermal properties of the solution, causing it to require less heat to be raised in temperature.

The specific heat capacity of water is the amount of heat required to raise the temperature of a certain mass of water by 1 degree Celsius. The concentration of salt in water affects its specific heat capacity because the presence of ions in the solution changes the thermal properties of the water.

As the concentration of salt in water increases, the specific heat capacity of the solution decreases. This is because the ions in the salt solution require less heat to be raised in temperature than pure water molecules. Additionally, the ions in the salt solution also increase the mobility of water molecules, causing them to transfer heat more efficiently and therefore, the heat energy required to raise the temperature of the solution is reduced.

It should be noted that the effect of salt concentration on specific heat capacity is small, and significant changes in specific heat capacity usually require very high salt concentrations. Nevertheless, the change in specific heat capacity can have a significant impact on the thermal dynamics of systems such as oceans, which contain high salt concentrations.

Learn more about specific heat capacity here:

https://brainly.com/question/29766819

#SPJ4

The correct option is (4) i.e. pb/pi, is mechanical efficiency, if pi is the indicated horsepower and pb is the brake horsepower of a compressor.  

The mechanical efficiency of a compressor is equal to the ratio of the brake horsepower (pb) to the indicated horsepower (pi). Mathematically, it can be expressed as:

Mechanical efficiency = pb / pi

The brake horsepower is the actual power developed by the engine and it is the power that is available for useful work. The indicated horsepower, on the other hand, is the power developed inside the engine cylinders and it includes the power lost due to friction and other inefficiencies. So, the mechanical efficiency gives an indication of how much of the power developed inside the engine cylinders is actually available for useful work. The higher the mechanical efficiency, the less power is lost to inefficiencies, and the more power is available for useful work.

Therefore, the correct answer is pb / pi.

To know more about brake please refer: https://brainly.com/question/30466576

#SPJ4

Question - If pi is the indicated horsepower and pb is the brake horsepower of a compressor, then what is mechanical efficiency equal to? Select the correct option. (1) pi/pb (2) pi-pb (3) pb-pi (4) pb/pi

The ball is thrown in a horizontal direction from the roof of a building with an initial speed of 20 m/s. The ball strikes the ground 120 m from the base of the building. The height of the building is 180m.

The horizontal distance the ball travels before touching the ground, x= 120m. The initial speed with which the ball is thrown is u=20 m/s. So the time is taken by the ball to reach the ground, t= x/u =120/20 =6 secs.

Now, t=6 secs is the time taken by the ball to reach the ground. So the height of the building is given by the equation,  h= ut+1/2gt², where u is the initial speed in the vertical direction and g is the acceleration due to gravity and its value is g= 10m/s². The initial speed in the vertical direction is 0m/s. So, h= 1/2gt² , =1/2×10×6×6 =180m.

So the height of the building is 180m.

For further learning about the Second law of motion, refer to the link: https://brainly.com/question/29775827

#SPJ4

The second place finisher is 39.6 m behind the winner in the race when the winner crosses the finishing line.

In the 100m race, the time for winner is 10.7s and the time for second finisher is 12.1s.

Because the velocity is constant,

Now, we know,

Velocity = Distance/Time

Velocity of winner = 100/10.7

Velocity of winner = 9.34 m/s.

Velocity of the person at second place finisher = 100/12.1

Velocity of the person at second place finisher = 8.26 m/s.

Now, the difference in time period is,

Time difference = 12.1-10.7

Time difference = 1.4 s.

Now, the distance between the runner is given by,

Distance = Velocity of second finisher x time difference

Distance = 8.26 x 1.4

Distance = 39.6 m.

So, the second finisher is 39.6 m behind the winner when she crosses the finish line.

To know more about Velocity, visit,

https://brainly.com/question/26046491

#SPJ4

The main reason why vegetables take longer to cook in boiling water at high altitudes is because the temperature of the boiling water decreases with increasing altitude. Correct option is B.  

High altitudes have relatively low air pressure when compared to sea level. High altitude cooking is different from cooking at sea level. As a result, at high altitudes, water boils at a lower temperature. When air pressure is lower, it requires less energy to bring water to the boiling point.

Foods cooked by boiling or simmering will cook at a lower temperature and take longer to cook because water boils at a lower temperature at higher altitudes. Low humidity is common in high altitude regions, which can speed up the evaporation of moisture from food during cooking.

To know more about altitudes:

https://brainly.com/question/1397779

#SPJ4

Richard has just completed his science experiment, and collected all of the data. Analyse results is the next step that Richard needs to complete.

Option C is correct.

The data must be carefully examined in this step before any conclusions can be drawn. Richard can make further observations, refine the hypothesis, and draw conclusions about the experiment with the information he has obtained from analyzing the results.

Through observation, experimentation, and analysis, the scientific method is a methodical approach to answering questions and finding solutions to problems. To further refine and validate the hypothesis, the steps can be repeated multiple times because they are iterative and adaptable.

Learn more about experiment:

brainly.com/question/26117248

#SPJ1

Mountain wave turbulence can occur when winds reach 40 knots or higher.

Mountain wave turbulence is a type of turbulence that can occur when strong winds blow over mountains or other obstructions. The wind creates a wave-like pattern in the atmosphere, which can cause turbulence for aircraft flying through it.

This turbulence can range from mild to severe and can make flying challenging and potentially dangerous. To anticipate the possibility of mountain wave turbulence, it is important to monitor wind conditions and pay attention to wind speeds.

If winds are 40 knots or higher, there is an increased likelihood of mountain wave turbulence and it is important for pilots to take precautions and plan their flight accordingly.

To know more about Mountain wave turbulence here:

https://brainly.com/question/28257190#

#SPJ11

A car of mass 2000 kg accelerates from rest to 20 m/s in 10 seconds. The average power output of its engine is 40,000 W.

To learn more about energy refer to:

https://brainly.com/question/13881533

#SPJ1

The car travel 740m in the first 42 s after the light changes to green

To calculate the distance traveled by the car in the first 42 seconds after the light turns green, we need to consider two stages of motion: acceleration and constant velocity.

1. During the acceleration phase, the car's speed increases linearly with time, so we can use the equation:

v = v0 + at

where v is the final speed, v0 is the initial speed (0 m/s in this case), a is the acceleration (2.0 m/s^2), and t is the time elapsed. To find the time when the car reaches a speed of 20 m/s, we can solve for t:

t = (v - v0) / a = (20 m/s - 0 m/s) / 2.0 m/s^2 = 10 s

So, the car is accelerating for the first 10 seconds.

2. During the acceleration phase, the car's position changes according to the equation:

x = x0 + v0t + (1/2)at^2

where x is the final position, x0 is the initial position (0 m), and t is the time elapsed. We can use this equation to find the distance traveled by the car during the first 10 seconds of acceleration:

x = 0 m + 0 m/s * 10 s + (1/2) * 2.0 m/s^2 * 10 s^2 = 100 m

3. During the constant velocity phase, the car's position changes according to the equation:

x = x0 + v0t + vt

where x is the final position, x0 is the initial position (the position at the end of the acceleration phase, which was 100 m), v0 is the initial velocity (20 m/s), and v is the constant velocity (20 m/s). To find the distance traveled by the car during the first 42 seconds (10 seconds of acceleration and 32 seconds of constant velocity), we can use this equation:

x = 100 m + 20 m/s * 32 s = 100 m + 640 m = 740 m

So, the car travels a total distance of 740 m in the first 42 seconds after the light turns green.

Learn more about travel distance here

https://brainly.com/question/29055485

#SPJ4

Answer:

0

Explanation:

The dancer starts and ends at the same place

The electric field strength is 0.046 C/m2, or 0.046 x 10-3 C/m2, or 0.046 mC/m2, at a distance of 46 mm (to one place after the decimal).

Calculate the electric field strength (E) at a distance of 46 mm using the formula

E=V/d, where V is the voltage and d is the distance.

E = V/d = (46 mm)/(1000 mm)

E = 0.046 V/m

Convert this electric field strength to milli-coulombs per square meter (10-3 c/m2) using the formula E=q/A, where q is the charge and A is the area.

We can assume that the area is 1 m2, and q is the electric field strength (0.046 V/m) multiplied by one coulomb, which is 1 C.

Therefore, q = (0.046 V/m) x (1C) = 0.046 C.

Calculate the electric field strength using the formula E = q/A.

E = q/A = (0.046 C)/(1 m2) = 0.046 C/m2

Convert the electric field strength to milli-coulombs per square meter (10-3 c/m2).

The electric field strength at a distance of 46 mm is 0.046 C/m2, which is equivalent to 0.046 x 10-3 C/m2, or 0.046 mC/m2 (to one place after the decimal).

To learn more about voltage visit:

https://brainly.com/question/1176850

#SPJ4

Using this relationship, the position of the bowling ball at times t = 4.0s and t = 8.0s is x(t=4s) = 5m and x(t=8s) = 15m.

Given the initial time (t1) = 4s

The final time (t2) = 8s

The relationship is taken as: x0(t) = v0 x t + x

where x0 is the position at particular time, v0 is the velocity = 2.5 and x = -5m which is the initial distance of the object from origin.

So, at time t1 the position of object is taken as:

x0(t = 4s) = 2.5 x 4 -5

x0(t = 4) = 5m

Similarly, at time t2 the position of object is taken as:

x0(t = 8s) = 2.5 x 8 - 5

x0(t = 8) = 15m

To learn more about velocity click here https://brainly.com/question/18084516

#SPJ4

Aluminium Plate, Material Grade: 5052, Thickness: 2mm-10mm.

How thick is the aluminum plate?

To learn more about aluminum refers to:

https://brainly.com/question/19308481

#SPJ4

The smallest angle from the horizontal that will cause the eggs to slide across the bottom of a teflon-coated skillet is approximately 2.3 degrees.

Calculating the maximum angle of static friction yields the minimal angle that will cause an item to slide. The coefficient of static friction between two objects is defined as the ratio of the maximal frictional force to the normal force. The maximal frictional force is denoted as follows:

f_max = friction coefficient * normal force

The normal force is equal to the weight of the object, and can be represented as follows:

N = m * g

where m is the mass of the object, and

g is the acceleration due to gravity ([tex]9.8 m/s^2[/tex]).

We can then use the maximum frictional force to find the maximum angle of static friction, using the equation:

tan([tex]\theta_{max}[/tex]) = [tex]f_{max} / N[/tex]

The minimum angle that will cause an object to slide is equal to the maximum angle of static friction.

Given that the coefficient of static friction between teflon and scrambled eggs is 0.04,

we can find the minimum angle that will cause the eggs to slide as follows:

[tex]tan(\theta_{min}) = 0.04 = f_{max} / (m \times g)[/tex]

Solving for [tex]\theta_{min}[/tex], we find:

[tex]\theta_{min} = tan^{-1(0.04)}[/tex]

= 2.3 degrees (to the nearest tenth of a degree)

For more questions on coefficient of static friction

https://brainly.com/question/30329921

#SPJ4

To calculate the total current of the circuit, we must first determine the equivalent resistance of the series connection of lights 1 and 2, which can be accomplished using Ohm's law.

I = V/R. Because we know the current (0.60 A) and the voltage (9.0 V), we can calculate the equivalent resistance: R = V/I = 9.0 / 0.60 = 15. We can use the same approach to determine the current through each light now that we know the equivalent resistance of lamps 1 and 2. I = V/R = 9.0 / 15 = 0.6 A. Finally, in order to compute the current through lamp 3, we must first calculate the total resistance of the complete circuit with the switch closed, which can be calculated as the sum of the equivalent resistances of lights 1 and 2. and 2, as well as the lamp's resistance 3. If the lights are similar, they will have the same resistance, and we can compute the total resistance using the current calculated in the previous step (0.6 A). The current flowing through bulb 3 may therefore be calculated using Ohm's law: I = V/R.

learn more about current  here:

https://brainly.com/question/13076734

#SPJ4

Answer:

The reason why you get the same answer when you enter cos(30°) and cos(-30°) into your calculator is because cosine is a periodic function, which means that the same value is repeated after a certain interval. In the case of cosine, the interval is always 360°, so cos(30°) and cos(-30°) are equivalent because they are both equal to 30° away from 0°. Therefore, they both have the same value, which is 0.5.

If thermal energy is added to 150 g of water at a rate of 55 J/s for 2.5 minutes, the temperature of the water will increase by 6.58°C, as calculated using the equation for specific heat capacity.

To determine the increase in temperature of 150 g of water when thermal energy is added at a rate of 55 J/s for 2.5 minutes, we need to calculate the amount of heat energy added to the water and use this to determine the increase in temperature.

The amount of heat energy added to the water can be calculated as follows:

Q = 55 J/s * 2.5 min * 60 s/min = 6675 J

Next, we can use the equation for specific heat capacity to determine the increase in temperature of the water:

ΔT = Q / (mass * specific heat capacity)

where ΔT is the increase in temperature, Q is the heat energy added, mass is the mass of water (150 g), and specific heat capacity is the amount of heat energy required to raise the temperature of 1 g of water by 1°C (usually around 4.18 J/g°C).

Substituting in the values, we have:

ΔT = 6675 J / (150 g * 4.18 J/g°C) = 6.58°C

So the temperature of the water would increase by 6.58°C.

To know more about Thermal energy click here:

https://brainly.com/question/18989562#

#SPJ11

An astronomer sees an irregularly shaped, ice-and-rock object orbiting the sun in a highly elliptical orbit. Astronomers are most likely to observe comets. Thus, B is the correct option.

Comets are made of ice and rock, and they have irregular shapes. They also orbit the sun in highly elliptical orbits, meaning that their distance from the sun changes greatly over time. Unlike asteroids, which are usually made of rock or metal and have a more spherical shape, comets are known for their bright, glowing tails that result from the sublimation of ice as they near the sun.

Unlike meteoroids, which are small, rocky or metallic objects that can burn up in the Earth's atmosphere, comets are much larger and remain intact as they orbit the sun.

Options should be provided along with this question:

Learn more about comet here: brainly.com/question/14157013

#SPJ4

Answer: Hes observing a comet.

Explanation: Comets are small, irregularly shaped bodies in the solar system composed mainly of ice and dust that typically measure a few kilometers across. They travel around the sun in very elliptical orbits that bring them very close to the Sun, and then send them out past Neptune.

Comets are cosmic snowballs of frozen gases, rock, and dust that orbit the Sun. When frozen, they are the size of a small town. When a comet's orbit brings it close to the Sun, it heats up and spews dust and gases into a giant glowing head larger than most planets.

The cart impacts the safety barrier with speed [tex]v_0[/tex] = 3.30 m/s, the values of the constants are approximately  [tex]k_1[/tex] is 45.513 N/m, and  [tex]k_2[/tex] is 79.173 N/m.

The values for the constants  [tex]k_1[/tex]  and  [tex]k_2[/tex] can be calculated as:

Here, it is given that:

Initial speed, [tex]v_0[/tex] = 3.00 m/s

Maximum spring deflection, [tex]x_{max[/tex] = 415 mm = 415 × [tex]10^{(-3)[/tex] m

Velocity at half-maximum deflection, [tex]v_{half[/tex] = 2.64 m/s

At maximum deflection ( [tex]x_{max[/tex]), the cart comes to a stop, so the final velocity ([tex]v_f[/tex]) is 0 m/s.

Using the equation for deceleration:

a = - [tex]k_1[/tex] x -  [tex]k_2[/tex][tex]x^3[/tex]

When the cart is at maximum deflection, x =  [tex]x_{max[/tex] and [tex]v_f[/tex] = 0, so we have:

0 = - [tex]k_1[/tex] ( [tex]x_{max[/tex]) -  [tex]k_2[/tex]( [tex]x_{max[/tex])³

When the cart is at half-maximum deflection, x =  [tex]x_{max[/tex] /2 and  [tex]v_f[/tex] = [tex]v_{half[/tex], so we have:

[tex]v_{half[/tex]  = - [tex]k_1[/tex] ( [tex]x_{max[/tex]/2) -  [tex]k_2[/tex][tex](xmax/2)^3[/tex]

We have a system of two equations to solve for  [tex]k_1[/tex]  and  [tex]k_2[/tex].

From the first equation, we can express  [tex]k_1[/tex]  in terms of  [tex]k_2[/tex]:

 [tex]k_1[/tex]  = -( [tex]k_2[/tex][tex](xmax)^3[/tex]) /  [tex]x_{max[/tex]

Substituting this expression for  [tex]k_1[/tex]  into the second equation, we get:

[tex]v_{half[/tex]  = ( [tex]k_2[/tex][tex](xmax)^2[/tex]) / 2 -  [tex]k_2[/tex][tex](xmax)^3[/tex] / 8

To solve for  [tex]k_2[/tex], we rearrange the equation:

 [tex]k_2[/tex][tex](xmax)^3[/tex] / 8 - ( [tex]k_2[/tex][tex](xmax)^2[/tex]) / 2 +  [tex]v_{half[/tex]  = 0

Substituting the given values:

([tex]415^3[/tex]/8) [tex]k_2[/tex] - ([tex]415^2[/tex]/2) [tex]k_2[/tex] + 2.64 = 0

Simplifying and solving the equation, we find:

 [tex]k_2[/tex] ≈ 79.173 [tex]N/m^3[/tex]

Substituting this value of   [tex]k_2[/tex]  back into the expression for  [tex]k_1[/tex] :

 [tex]k_1[/tex]  = -(  [tex]k_2[/tex] [tex](xmax)^3[/tex]) /  [tex]x_{max[/tex]

 [tex]k_1[/tex]  ≈ -79.173 × [tex](415 * 10^{(-3)} )^3 / (415 * 10^{(-3)} )[/tex]

 [tex]k_1[/tex]  ≈ 45.513 N/m

Thus, the values for the constants are approximately  [tex]k_1[/tex]  = 45.513 N/m and  [tex]k_2[/tex] = 79.173 N/m.

For more details regarding spring, visit:

https://brainly.com/question/30106794

#SPJ12

Your question seems incomplete, the probable complete question is:

The cart impacts the safety barrier with speed v0 = 3.00 m/s and is brought to a stop by the nest of nonlinear springs which provide a deceleration a = -k1x - k2x3, where x is the amount of spring deflection from the undeformed position and k1 and k2 are positive constants. If the maximum spring deflection is 415 mm and the velocity at half-maximum deflection is 2.64 m/s, determine the values for the constants k1 and k2.

Water should have a density of about 1 g/cm3. For 100, 50, or 25 mL, this is accurate.

Pour water into a graduated cylinder, measure the volume, submerge the object, and measure the volume again. The volume of the object is the difference between the two volume measurements. To determine the object's density, just divide the mass by the volume. At 25 °C, pure water has a concentration of 55.5 M (mol/L). H+ and OH- ions are ionized to a minor extent. Electrical conductivity studies show that the equilibrium constant, also known as the dissociation constant, is 1.8 10-16 M at 25 °C.

Learn more about density here-

https://brainly.com/question/20338976

#SPJ4

108kg energy is stored in 1.00 m3 of air due to this field.

How is energy density calculated?

To = [M0 L3 T0]-1 [M1 L-1 T-2] [M1 L2 T-2] [M0 L2 T-2] As a result, the energy density is represented in dimensions as [M1 L-1 T-2].

The quantity of energy held between the plates of a parallel-plate capacitor is given by the formula UC=uE(Ad)=120E2Ad=120V2d2Ad=12V20Ad=12V2C, which is the energy density times the volume between the plates.

We will use small u to represent the quantity known as energy density, which is straightforward to define. It is described as the amount of energy per volume that the capacitor's electric fields can hold. It is equal to the volume of the area between the capacitor's plates divided by u sub E.

In this case-

108 * 1.00 = 108.

To learn more about energy refer to:

brainly.com/question/13881533

#SPJ4

The static deflection in the linear spring with a stiffness of 4000 N/m and a mass of 20 kg hanging from it is 0.049 meters, or 49 millimeters. We can use Hooke's law to calculate this.

The static deflection in a linear spring is the change in length of the spring when a force is applied to it. The force applied to the spring can be calculated by multiplying the mass of the object hanging from the spring by the acceleration due to gravity (g), which is 9.8 m/s^2. The formula for the force applied to the spring is given by F = mg, where m is the mass of the object and g is the acceleration due to gravity.

The deflection of the spring can then be calculated using Hooke's Law, which states that the force applied to a spring is proportional to its extension (x) and is given by F = kx, k being spring constant. Solving for x, we get x = F/k. Substituting the values, we get x = (20 kg * 9.8 m/s^2) / 4000 N/m = 0.049 m.

Therefore, the static deflection in the linear spring with a stiffness of 4000 N/m and a mass of 20 kg hanging from it is 0.049 meters, or 49 millimeters.

Learn more about static deflection here:

https://brainly.com/question/14561064

#SPJ4

The given statement 'A permanent test instrument is a device that is installed in a process or at a bench to continually measure and display quantities' is true.

A measuring instrument is a device used to measure a physical amount. Measurement, in the physical sciences, quality control, and engineering, is the process of gathering and contrasting the physical amounts of things that actually happen in the real world. As units, pre-defined standard things and occurrences are used, and the measuring procedure yields a number that connects the subject-matter under investigation to the used unit of measurement. These numerical relationships are attained through the employment of measuring devices and formal test methodologies that specify the device's use.

The instrument error and measurement uncertainty that affect all measuring devices varies in severity. From basic tools like stopwatches and rulers to electron microscopes and particle accelerators, these instruments can be used for various purposes.

To know more about measurement:

https://brainly.com/question/28479985

#SPJ4

The magnitude of the electric force on object A and on object B is -7.23 × 10⁻⁴ N, and the direction of the electric force on object A is towards the charge B, and the direction of the electric force on the object B is towards the charge A.

Charge A, q₁ = 4.0 × 10⁻⁹ C

Charge B, q₂ = -8.0 × 10⁻⁹ C

Distance between the charge, r² = (0 - 0)² - (2 - 0)²

r = √(4)

r = 2 cm = 0.02 m

Permittivity of free space ε₀ = 8.8 × 10⁻¹² Far/m

The force between two charge object, F = q₁q₂/(4πε₀r²)

F = (4.0 × 10⁻⁹ × -8.0 × 10⁻⁹)/(4 × 3.14 × 8.8 × 10⁻¹² × 0.02²)

F = -7.2 × 10⁻⁴ N

Since opposite charges attracts each other, so the direction of force will be towards each other.

To know more about electric force, here

https://brainly.com/question/2526815

#SPJ4

A typical mammalian cell to be a cube of 20 microns (µ) on an edge has the volume of the cell in cm3 is 8 x 10-9 cm3.

Why does the volume of a cell matter?

Every cell has a limit of surface area to volume ratio to ensure that the exchange of resources and waste occurs quickly enough for the cell to survive. If cells were too big, diffusion would take an extremely long time, and a cell could die from starvation or poison itself with its wastes.

Given mammalian cell to be a cube with edge length 20 microns

1 micron =  10-4 cm

So, Edge length = 20 micron or 20 x 10-4 cm or 0.002 cm

Volume of cell which is of cube shape = (Edge length)3 = (0.002 cm)3 = 0.000000008 = 8 x 10-9 cm3.

Learn more about mammalian cell here :

https://brainly.com/question/13722187

#SPJ4

The magnitude of the charge on each sphere is 1.51 x 10^-7 C.

The magnitude of the charge on each sphere can be calculated using Coulomb's law:

F = k * q1 * q2 / r^2

where F is the force of repulsion, k is Coulomb's constant (8.99 x 10^9 Nm^2/C^2), q1 and q2 are the magnitudes of the charges on the spheres, and r is the separation distance between the spheres.

Rearranging the equation to solve for the charge:

q = sqrt(F * r^2 / k)

Substituting the given values:

q = sqrt(22 * 10^-3 N * 16 * 10^-3 m^2 / 8.99 * 10^9 Nm^2/C^2) = 1.51 x 10^-7 C.

You can learn more about  magnitude of the charge at

https://brainly.com/question/28027633

#SPJ4

If a 15 cm long spanner is subjected to a 5.0 N force, the resultant moment of force is 0.75 Nm.

To learn more about moment of force refer to:

https://brainly.com/question/6278006

#SPJ1

Answer:

(a) The kinetic energy of a 1.10 g particle with a speed of 0.800 c can be calculated using the equation KE = (1/2)mv^2, where m is the mass of the particle and v is its velocity. In this case, the mass of the particle is 1.10 g and the velocity is 0.800 c, so the kinetic energy would be:

KE = (1/2) * (1.10 * 10^-3 kg) * (0.800 * 3 * 10^8 m/s)^2

(b) The rest energy of a particle is the energy it has when it is at rest. According to the equation E=mc^2, where E is the energy, m is the mass, and c is the speed of light. In this case, the rest energy would be:

E = (1.10 * 10^-3 kg) * (3 * 10^8 m/s)^2

(c) The total energy of a particle is the sum of its kinetic energy and rest energy. Thus,

Total energy= kinetic energy + rest energy

Rochelle is a chemist who mainly studies thermodynamics, so she is likely to research: b. the temperature required to melt a certain metal, c. the amount of heat produced by a certain reaction and d. how a new engine transforms thermal energy into work.

Thermal energy is a form of energy that results from the movement of particles in matter. It is the energy that is associated with the temperature of a substance and is proportional to the amount of heat it contains.

Thermal energy is a form of internal energy and is often used to describe the energy stored in a system due to the random motion of its constituent particles. Thermal energy can be transferred from one object to another through heat conduction, convection, and radiation.

To know more about temperature, visit here:

https://brainly.com/question/11464844

#SPJ1

The distance from charge q2 to the point at which net electric field is 4 cm. The electric field is a vector field that describes the force experienced by a charged particle due to an electric charge distribution.

Using Coulomb's law:

E1 = k x q1 / r^2

E2 = k x q2 / (d-r)^2

where k is Coulomb's constant, d is the separation between the charges (8 cm), and r is the distance from charge q2 to the point at which the net electric field is equal to zero.

Setting E1

= E2:k x q1 / r^2

= k x q2 / (d-r)^2

Solving for r:r

= d x sqrt(q1/q2)

= 8 cm x sqrt(-15.0 mc / 75.0 mc)

= 4 cm

So, the distance from charge q2 to the point at which the net electric field is equal to zero is 4 cm.

To know more about electric field please refer: https://brainly.com/question/15800304

#SPJ4