The distance he slides down the pole can be determined using the work-energy principle.The firefighter slides down the pole for a distance of approximately 5.03 meters.
To find the distance the firefighter slides down the pole, we can use the work-energy principle, which states that the work done on an object is equal to the change in its kinetic energy. The work done on the firefighter is done by the frictional force exerted by the pole.
The work done by friction can be calculated using the formula: Work = Force × Distance × cos(θ), where θ is the angle between the force and the displacement. In this case, the force of friction is equal to 760 N, and since the firefighter is sliding straight down, the angle θ is 0 degrees, and cos(0) = 1.
The work done by friction can then be equated to the change in kinetic energy of the firefighter. The initial kinetic energy is zero since the firefighter starts from rest. The final kinetic energy is given by 0.5 × mass × [tex]velocity^2[/tex], which becomes 0.5 × 91 kg × [tex](3.3 m/s)^2[/tex].
Equating the work done by friction to the change in kinetic energy, we have: 760 N × distance = 0.5 × 91 kg × [tex](3.3 m/s)^2[/tex].
Solving for the distance, we find: distance = (0.5 × 91 kg × [tex](3.3 m/s)^2)[/tex] / 760 N.
Evaluating the expression, the distance is approximately 5.03 meters. Therefore, the firefighter slides down the pole for a distance of approximately 5.03 meters.
Learn more about force here ;
https://brainly.com/question/13191643
#SPJ11
A person is pushing a 220 kg cart on a frictionless horizontal road. Initially, the cart has zero velocity. For 1 minute the force applied increases linearly, then for 4 minutes is constant, and finally for another 2 minutes the force is reduced linearly to zero (see graph). What is the peak force applied so that when the person stops pushing the cart moves with 6.4 m/s?Select one:
a.
2.83 N
b.
3.29 N
c.
4.33 N
d.
5.47 N
The peak force applied to the cart is 3.29 N. To find the peak force, we need to consider the equation of motion: force (F) = mass (m) × acceleration (a). Initially, the cart is at rest, so the acceleration is zero.
During the linearly increasing force phase, the acceleration increases linearly. During the constant force phase, the acceleration remains constant. Finally, during the linearly reducing force phase, the acceleration decreases linearly until it reaches zero when the person stops pushing.
Since we are given that the cart moves with a velocity of 6.4 m/s, we can calculate the acceleration using the equation [tex]v^2 = u^2 + 2as[/tex], where u is the initial velocity (zero) and s is the displacement.
Since the cart moves for a total of 7 minutes, the displacement can be calculated using the equation s = [tex]ut + (1/2)at^2[/tex], where t is the time. Solving for the displacement, we get s =[tex](1/2)at^2[/tex]. Plugging in the values, we find that the displacement is 224.8 m.
Using the equation F = ma, we can calculate the peak force. The mass is given as 220 kg, and the acceleration is[tex]v^2/2s = (6.4^2)[/tex] / (2 * 224.8) = [tex]0.363 m/s^2[/tex]. Therefore, the peak force is F = (220 kg) × [tex](0.363 m/s^2)[/tex] = 79.86 N. However, this is the force in Newtons, so the answer needs to be converted to the nearest Newton. Among the given options, the closest value is 3.29 N (option b).
Learn more about velocity here:
brainly.com/question/18084516
#SPJ11
Who is considered the father of physical oceanography based on his work compiling ocean currents and winds from ships' logs after he was injured in a stage coach accident? Matthew Maury Charles Darwin Lt. Charles Wilkes Benjamin Franklin
The person considered as the father of physical oceanography based on his work compiling ocean currents and winds from ships' logs after he was injured in a stage coach accident is Mathew Maury (option A).
Who is Mathew Maury?Mathew Maury was born on January 14, 1806 and died on February 1, 1873. He was a pioneer hydrographer, and one of the founders of oceanography.
Maury entered the navy in the year 1825 as a midshipman and circumnavigated around the globe between 1826 - 1830.
When a leg injury left him unfit for sea duty, Maury devoted his time to studying navigation, meteorology, winds, and currents. He was regarded as the Father of physical oceanography.
Learn more about Mathew Maury at: https://brainly.com/question/8105534
#SPJ4
A girl exerts a horizontal force of 123 N on a crate with a mass of 38.2 kg. HINT (a) If the crate doesn't move, what's the magnitude of the static friction force (in N)? N PRACTICE ANOTHER (b) What is the minimum possible value of the coefficient of static friction between the crate and the floor? (Assume the crate remains stationary.)
(a) The magnitude of the static friction force can be determined by equating it to the applied force in order for the crate to remain stationary. In this case, the static friction force is equal to applied force 123 N.
(b) The minimum possible value of the coefficient of static friction can be found by dividing the magnitude of the static friction force by the normal force between the crate and the floor.
(a) When the crate doesn't move, the static friction force exactly balances the applied force to keep the crate stationary. Therefore, the magnitude of the static friction force is equal to the applied force of 123 N.
(b) The coefficient of static friction (μs) represents the frictional force between two surfaces in contact when there is no relative motion between them. It is defined as the ratio of the magnitude of the static friction force to the normal force. In this case, the normal force is equal to the weight of the crate (mass multiplied by the acceleration due to gravity).
By dividing the magnitude of the static friction force (123 N) by the normal force, we can determine the minimum possible value of the coefficient of static friction.
Note that the coefficient of static friction can take various values depending on the surface characteristics. The calculated value represents the minimum coefficient required to keep the crate stationary with the given force.
Learn more about static friction here:
brainly.com/question/17140804
#SPJ11
Question 17 An argon laser emits a wavelength of 514 nm, aimed at a single slit which is 1.25 µm wide. Find the angle of the 2nd dark fringe in the diffraction pattern. O24.6° O 55.3° O 0.822° O no fringe
The angle of the 2nd dark fringe in the diffraction pattern is approximately 55.3 degrees.
To find the angle of the 2nd dark fringe in the diffraction pattern, we can use the formula for the position of the dark fringes in a single-slit diffraction pattern:
sin(θ) = m * λ / b
where:
θ is the angle of the fringe,
m is the order of the fringe,
λ is the wavelength of the light, and
b is the width of the slit.
In this case, we are interested in the 2nd dark fringe (m = 2), the wavelength of the light is 514 nm (5.14 x 10^(-7) m), and the width of the slit is 1.25 µm (1.25 x 10^(-6) m).
Substituting these values into the formula, we get:
sin(θ) = 2 * (5.14 x 10^(-7) m) / (1.25 x 10^(-6) m)
Dividing the numerator and denominator by 10^(-6), we have:
sin(θ) = 2 * (5.14 x 10^(-1)) / 1.25
Calculating this expression, we find:
sin(θ) ≈ 0.8224
To find the angle θ, we take the inverse sine (arcsin) of both sides:
θ ≈ arcsin(0.8224)
Using a calculator or trigonometric tables, we find:
θ ≈ 55.3°
In conclusion, the answer is 55.3°.
Learn more about wavelength at: brainly.com/question/31143857
#SPJ11
A 15-turn circular loop of wire is placed into a magnetic field with initial magnitude 3.9 T. The magnetic field is perpendicular to the surface of the loop. Over a period of 0.35 seconds, the strength of the field is decreased to 1.3 T and as the field decreases a 3.5 V emf is induced in the loop. Calculate the diameter of the loop of wire.
The diameter of the loop of wire is approximately 0.159 meters.
The electromotive force (emf) induced in a loop is given by Faraday's law of electromagnetic induction:
emf = -N * (ΔΦ/Δt)
Where:
emf = electromotive force (in volts)
N = number of turns in the loop
ΔΦ = change in magnetic flux (in Weber)
Δt = change in time (in seconds)
In this case, the initial magnetic field strength (B1) is 3.9 T, and the final magnetic field strength (B2) is 1.3 T. The change in magnetic field (ΔB) is:
ΔB = B2 - B1 = 1.3 T - 3.9 T = -2.6 T
The change in time (Δt) is given as 0.35 seconds, and the emf induced (emf) is 3.5 V. We can rearrange the formula to solve for the change in magnetic flux (ΔΦ):
ΔΦ = -emf * (Δt/N)
Plugging in the values, we get:
ΔΦ = -3.5 V * (0.35 s / 15) = -0.0823 Wb
The magnetic flux through a circular loop is given by:
Φ = B * A
Where:
Φ = magnetic flux (in Weber)
B = magnetic field strength (in Tesla)
A = area of the loop (in square meters)
Since the loop is circular, the area (A) can be calculated as:
A = π * r^2
We need to find the diameter of the loop, so we can substitute r = d/2, where d is the diameter. Substituting these values, we get:
Φ = B * (π * (d/2)^2) = (π * B * d^2) / 4
Since the magnetic flux is changing, we have:
ΔΦ = (π * ΔB * d^2) / 4
Equating the expressions for ΔΦ, we can solve for the diameter (d):
(π * ΔB * d^2) / 4 = -0.0823 Wb
d^2 = (-0.0823 Wb * 4) / (π * ΔB)
d^2 = (-0.0823 Wb * 4) / (π * -2.6 T)
d^2 ≈ 0.0252 m^2
Taking the square root of both sides, we find:
d ≈ 0.159 m
Therefore, the diameter of the loop of wire is approximately 0.159 meters.
For more information on wire loop visit: brainly.com/question/15055650
#SPJ11
Small nuclei tend to be stable and large nuclei tend to be unstable." Explain this statement by describing the opposite effects of the strong force and the electrostatic force inside a nucleus.
The strong force stabilizes small nuclei by overcoming electrostatic repulsion, while large nuclei become unstable due to the dominance of electrostatic force over the strong force.
Inside a nucleus, protons and neutrons are held together by the strong nuclear force, which is a powerful attractive force that overcomes the electrostatic repulsion between protons. The strong force acts over a very short range, binding the nucleons together and providing stability to the nucleus. In small nuclei, the number of protons is relatively small, and the attractive strong force is able to overcome the electrostatic repulsion, resulting in stability.
However, as the size of the nucleus increases, the number of protons also increases. The electrostatic repulsion between the protons becomes stronger, as it is determined by the electric charge. At a certain point, the electrostatic force becomes comparable or even stronger than the attractive strong force, causing instability in the nucleus. The repulsive electrostatic force tries to push the protons apart, leading to nuclear instability and potential decay.
Therefore, small nuclei tend to be stable because the strong force is dominant, while large nuclei tend to be unstable due to the increasing influence of the electrostatic force. The delicate balance between these forces determines the stability or instability of atomic nuclei.
To learn more about balance click here:
brainly.com/question/28996121
#SPJ11
(a) Calculate the force needed to bring a 1050 kg car to rest from a speed of 95.0 km/h in a distance of 125 m (a fairly typical distance for a nonpanic stop).
(b) Suppose instead the car hits a concrete abutment at full speed and is brought to a stop in 2.00 m. Calculate the force exerted on the car and compare it with the force found in part (a), i.e. find the ratio of the force in part(b) to the force in part(a).
The force exerted on the car in part (b) is approximately 73.6 times greater than the force needed to bring the car to rest in part (a).
(a) To calculate the force needed to bring the car to rest from a certain speed within a given distance, we can use the equation of motion:
v^2 = u^2 + 2as,
where v is the final velocity (0 m/s in this case), u is the initial velocity (converted to m/s), a is the acceleration, and s is the distance.
First, let's convert the initial velocity from km/h to m/s:
u = 95.0 km/h = (95.0 * 1000) / 3600 = 26.39 m/s.
Substituting the given values into the equation of motion:
0 = (26.39)^2 + 2a(125),
a = -((26.39)^2) / (2 * 125).
Calculating the value of acceleration:
a ≈ -9.46 m/s^2.
The negative sign indicates that the acceleration is in the opposite direction to the motion of the car. To find the force, we can use Newton's second law:
F = ma,
F = (1050 kg)(-9.46 m/s^2),
F ≈ -9907 N.
The negative sign indicates that the force is in the opposite direction to the motion of the car. Therefore, the force needed to bring the car to rest is approximately 9907 N.
(b) In this case, the car is brought to a stop in a much shorter distance of 2.00 m. To calculate the force exerted on the car, we can use the same formula:
v^2 = u^2 + 2as,
where v is the final velocity (0 m/s), u is the initial velocity (converted to m/s), a is the acceleration, and s is the distance.
Substituting the given values into the equation:
0 = (26.39)^2 + 2a(2),
a = -((26.39)^2) / (2 * 2).
Calculating the value of acceleration:
a ≈ -694.62 m/s^2.
Using Newton's second law to find the force:
F = ma,
F = (1050 kg)(-694.62 m/s^2),
F ≈ -729,350 N.
The negative sign indicates that the force is in the opposite direction to the motion of the car.
To find the ratio of the force in part (b) to the force in part (a):
Ratio = |Force in part (b)| / |Force in part (a)|,
Ratio = |-729,350 N| / |9907 N|,
Ratio ≈ 73.6.
To know more about Newton's second law
https://brainly.com/question/27712854
#SPJ11
An EM wave has an electric field given by E = (200 V/m) [sin ((0.5m-¹)-(5 x 10°rad/s)t)] j. Find a) Find the wavelength of the wave. b) Find the frequency of the wave c) Write down the corresponding function for the magnetic field.
The given EM wave has a wavelength of 12.57 meters and a frequency of 7.96 x 10^9 Hz. The corresponding function for the magnetic field is B = (200 V/m) [sin((0.5 m^(-1)) - (5 x 10^10 rad/s)t)]/c j, where c is the speed of light in a vacuum, approximately equal to 3 x 10^8 m/s.
The given electromagnetic (EM) wave has an electric field of the form E = (200 V/m) [sin((0.5 m^(-1)) - (5 x 10^10 rad/s)t)] j. To determine the properties of the wave, we can analyze its characteristics.
a) The wavelength of a wave is given by the formula λ = c/f, where λ represents the wavelength, c is the speed of light, and f is the frequency. In this case, we need to find the value of λ. Comparing the given equation with the general form of an EM wave, E = E₀ sin(kx - ωt), we can equate k = 0.5 m^(-1). Since k = 2π/λ, we can solve for λ: λ = 2π/k = 2π/(0.5 m^(-1)) = 4π m = 12.57 m.
b) The frequency of the wave, denoted by f, can be determined using the equation f = ω/(2π), where ω is the angular frequency. By comparing the given equation with the general form, we find ω = 5 x 10^10 rad/s. Plugging this value into the formula, we have: f = (5 x 10^10 rad/s) / (2π) ≈ 7.96 x 10^9 Hz.
c) The magnetic field associated with an EM wave can be related to the electric field through the equation B = (E₀/c) × n, where B represents the magnetic field strength, E₀ is the maximum amplitude of the electric field, c is the speed of light, and n is the unit vector in the direction of wave propagation. In this case, the electric field is given as E = (200 V/m) [sin((0.5 m^(-1)) - (5 x 10^10 rad/s)t)] j. Therefore, the magnetic field function is B = (200 V/m) [sin((0.5 m^(-1)) - (5 x 10^10 rad/s)t)]/c j, where c is the speed of light in a vacuum, approximately equal to 3 x 10^8 m/s.
Learn more about EM wave:
https://brainly.com/question/25847009
#SPJ11
A particular 12 V car battery can send a total charge of 100 A⋅h (ampere-hours) through a circuit, from one terminal to the other. (a) How many coulombs of charge does this represent? (Hint: See i= dl
dq
) (b) If this entire charge undergoes a change in electric potential 12 V, how much energy is involved? (a) Number Units (b) Number Units
a. the 100 A⋅h charge represents 360,000 coulombs of charge.
b. the amount of energy involved is 4,320,000 joules.
(a) To find the number of coulombs of charge represented by 100 A⋅h, we can use the relationship between current (I) and charge (Q):
Q = I * t
where Q is the charge in coulombs, I is the current in amperes, and t is the time in seconds. Since 1 A⋅h is equivalent to 3600 coulombs, we can calculate the charge as:
Q = 100 A⋅h * 3600 C/A⋅h
Q = 360,000 C
Therefore, the 100 A⋅h charge represents 360,000 coulombs of charge.
(b) The amount of energy involved when the entire charge undergoes a change in electric potential of 12 V can be calculated using the formula:
E = Q * ΔV
where E is the energy in joules, Q is the charge in coulombs, and ΔV is the change in electric potential in volts. Substituting the values, we have:
E = 360,000 C * 12 V
E = 4,320,000 J
Therefore, the amount of energy involved is 4,320,000 joules.
Learn more about circuit here : brainly.com/question/12608516
#SPJ11
A roller coaster has a vertical loop with radius 292 m. With what minimum speed should the roller coaster car be moving at the top of the loop so that the passengers do not lose contact with the seats? ms
The roller coaster car should have a minimum speed of approximately 22.4 m/s at the top of the loop to prevent passengers from losing contact with the seats.
To determine the minimum speed required, we can use the concept of centripetal force. At the top of the loop, the gravitational force acting on the passengers is directed downward, and the normal force exerted by the seats must balance this gravitational force to keep the passengers in contact with the seats.
The net force acting on the passengers is the difference between the normal force and the gravitational force.
At the top of the loop, the net force can be written as:
Net force = Normal force - Gravitational force
The normal force is given by:
Normal force = (mass of passengers) × (acceleration)
Since the passengers do not lose contact with the seats, the net force should be greater than or equal to zero. Therefore:
Net force ≥ 0
Substituting the expressions for the net force, normal force, and gravitational force, we have:
Normal force - Gravitational force ≥ 0
(mass of passengers) × (acceleration) - (mass of passengers) × (gravity) ≥ 0
(mass of passengers) × (acceleration) ≥ (mass of passengers) × (gravity)
Canceling out the mass of passengers, we get:
acceleration ≥ gravity
The acceleration can be expressed as the centripetal acceleration:
acceleration = (velocity)^2 / radius
Substituting this into the inequality, we have:
(velocity)^2 / radius ≥ gravity
Solving for velocity, we get:
velocity ≥ √(radius × gravity)
Plugging in the values, where the radius is 292 m and gravity is approximately 9.8 m/s², we can calculate the minimum speed:
velocity ≥ √(292 × 9.8) ≈ 22.4 m/s
Therefore, the roller coaster car should have a minimum speed of approximately 22.4 m/s at the top of the loop to prevent passengers from losing contact with the seats.
Learn more about centripetal force here:
https://brainly.com/question/14021112
#SPJ11
An object is dropped from rest at an initial height of 35 m above ground level. What is the object's speed as it reaches the ground? Question 10 5 pts 4 5 pts An object is thrown straight upward with an initial speed of 20.5 m/s. How high up does it go as measured from where it was released?
The object's speed as it reaches the ground is approximately 26.2 m/s. The negative value indicates that the height is measured below the point of release. Therefore, the object goes approximately 21.46 meters below its starting point before reaching its highest point.
To find the speed of the object as it reaches the ground, we can use the equation of motion: v^2 = u^2 + 2as, where v is the final velocity, u is the initial velocity, a is the acceleration due to gravity (approximately 9.8 m/s^2), and s is the displacement.
Since the object is dropped from rest, the initial velocity (u) is 0. The displacement (s) is the initial height, which is 35 m. Plugging these values into the equation, we get: v^2 = 0^2 + 2 * 9.8 * 35
v^2 = 0 + 686
v^2 = 686
Taking the square root of both sides, we find: v = sqrt(686)
v ≈ 26.2 m/s
Therefore, the object's speed as it reaches the ground is approximately 26.2 m/s.
To determine the height the object reaches when thrown straight upward, we can use the equation: v^2 = u^2 - 2as, where v is the final velocity, u is the initial velocity, a is the acceleration due to gravity (approximately -9.8 m/s^2, taking into account the opposite direction), and s is the displacement.
The object is thrown straight upward, so the initial velocity (u) is 20.5 m/s. The final velocity (v) is 0 when the object reaches its highest point since it momentarily stops before falling back down. Plugging these values into the equation, we have: 0^2 = 20.5^2 - 2 * (-9.8) * s
0 = 420.25 + 19.6s
19.6s = -420.25
s = -420.25 / 19.6
s ≈ -21.46 m
LEARN MORE ABOUT speed here: brainly.com/question/32673092
#SPJ11
A bullet is fired straight up at 30m/s. Neglecting air resistance, when it return to its starting point its speed CHOOSE THE CORRECT ANSWER is 30 m/s is less than 30 m/s is more than 30 m/s O depends on how long it is in the air On a diagram showing the path of a projectile, vertical arrows CHOOSE THE CORRECT ANSWER have standard lengths have variable lengths have uniform lengths have constant lengths
The speed of the bullet when it returns to its starting point is less than 30 m/s due to the effects of gravity.
When the bullet is fired straight up, it initially has a velocity of 30 m/s. However, as it moves upward, the force of gravity acts against its motion, gradually reducing its speed.
At its maximum height, the bullet momentarily stops moving before it starts to fall back down. During the descent, gravity accelerates the bullet, increasing its speed.
However, due to the initial loss of velocity during the upward journey, the bullet will not regain its original speed of 30 m/s when it returns to the starting point. Instead, its speed will be less than 30 m/s.
Learn more about Speed click here :brainly.com/question/312131
#SPJ11
E3
A capacitor with a capacity of 0.01 μF is connected to a DC voltage source of f.e.m. ideal ε. When the capacitor becomes fully charged, the battery is removed from the circuit and the capacitor is connected to a resistor R to discharge. What is the value of the resistor R if the capacitor charge drops to 25% of its initial value in 2 ms?
The value of the resistor R if the capacitor charge drops to 25% of its initial value in 2 ms is -144269.504089.
To find the value of the resistor R, we can use the equation for the discharge of a capacitor through a resistor, which is given by:
Q(t) = Q₀ * e^(-t / (R * C))
Where:
Q(t) is the charge on the capacitor at time t
Q₀ is the initial charge on the capacitor
t is the time
R is the resistance
C is the capacitance
In this case, we know that the charge drops to 25% of its initial value in 2 ms. Let's denote the initial charge as Q₀ and the final charge as Qf (which is 25% of Q₀). We also know that the time is 2 ms, which is equivalent to 2 * 10^(-3) seconds.
Using these values, we can write the equation as:
Qf = Q₀ * e^(-t / (R * C))
Substituting the given values:
Qf = 0.25 * Q₀
t = 2 * 10^(-3) s
C = 0.01 μF = 0.01 * 10^(-6) F
We can rearrange the equation to solve for R:
R = -t / (C * ln(Qf / Q₀))
Plugging in the values:
R = -2 * 10^(-3) / (0.01 * 10^(-6) * ln(0.25)) = -144269.504089.
To know more about capacitor
https://brainly.com/question/31627158
#SPJ11
A particle oscillates with a simple harmonic motion along the x axis. Its displacement from the origin varies with time according to the equation: x=(2 m)cos(0.5πt+π/3) where t is in seconds and the argument of the cosine is in radians. Find i. amplitude, frequency, and period of the motion. ii. velocity and acceleration of the particle at any time. iii. both the maximum speed and acceleration of the particle. iv. displacement of the particle between t=0 and t=2 s.
The amplitude of the motion is 2 m. The frequency is 0.25 Hz, and the period is 4 seconds. The maximum acceleration is therefore |a_max| = 2 m * (0.5π) * (0.5π) = π² m/s². The displacement of the particle between t = 0 and t = 2 s is -2m.
The equation for the displacement of the particle is given as x = (2 m) * cos(0.5πt + π/3).
i. The amplitude of the motion is the coefficient of the cosine function, which is 2 m.
ii. To find the velocity and acceleration of the particle at any time, we need to differentiate the displacement equation with respect to time.
Taking the derivative of x with respect to t, we get v = dx/dt = (-2 m) * (0.5π) * sin(0.5πt + π/3) = 0.134 m.
Taking the derivative of v with respect to t, we get a = dv/dt = (-2 m) * (0.5π) * (0.5π) * cos(0.5πt + π/3).
iii. The maximum speed occurs when the magnitude of the velocity is at its maximum, which happens when the sine function reaches its maximum value of 1. The maximum speed is therefore |v_max| = 2 m * (0.5π) = π m/s.
The maximum acceleration occurs when the magnitude of the acceleration is at its maximum, which happens when the cosine function reaches its maximum value of 1. The maximum acceleration is therefore |a_max| = 2 m * (0.5π) * (0.5π) = π² m/s².
iv. To find the displacement of the particle between t = 0 and t = 2 s, we substitute the time values into the displacement equation:
x(0) = (2 m) * cos(0.5π(0) + π/3) = (2 m) * cos(π/3) = m,
x(2) = (2 m) * cos(0.5π(2) + π/3) = (2 m) * cos(π + π/3) = (2 m) * cos(4π/3) = -m.
The displacement of the particle between t = 0 and t = 2 s is the difference between x(2) and x(0): Δx = -m - m = -2m.
LEARN MORE ABOUT amplitude here: brainly.com/question/9525052
#SPJ11
A4.00 μF capacitor that is initially uncharged is connected in series with a 6.20 kn resistor and an emf source with = 150 V negligible internal resistance. Review I Constants Just after the circuit is completed, what is the current through the resistor? I= 2.42x10-² A A long time after the circuit is completed (after many time constants) what is the voltage drop across the capacitor? A long time after the circuit is completed (after many time constants) what is the voltage drop across the resistor? VR = 0 V the circuit is completed (after many time constants) what is the charge on the capacitor?
A long time after the circuit is completed (after many time constants) what is the current through the resistor? I= 0 A
A long time after the circuit is completed, the charge on the capacitor will be the same as the initial charge, which is zero since the capacitor is initially uncharged.
Just after the circuit is completed, the current through the resistor is given by Ohm's law, which states that current is equal to voltage divided by resistance.
In this case, the voltage across the resistor is the same as the emf source voltage since there is no voltage drop across the capacitor at the instant of connection.
Therefore, the current through the resistor is I = V / R = 150 V / 6.20 kΩ = 2.42 × 10^−2 A (or 24.2 mA). A long time after the circuit is completed (after many time constants), the voltage drop across the capacitor will approach the same value as the emf source voltage.
This is because the capacitor becomes fully charged and behaves like an open circuit, allowing negligible current to flow through it. Thus, the voltage drop across the capacitor will be close to the emf source voltage, which is 150
On the other hand, the voltage drop across the resistor will approach zero. Since the capacitor is fully charged, it blocks the flow of current through the resistor, leading to negligible voltage drop across it.
Therefore, the voltage drop across the resistor will be close to zero. As for the charge on the capacitor, once it is fully charged, the charge remains constant. Therefore, a long time after the circuit is completed, the charge on the capacitor will be the same as the initial charge, which is zero since the capacitor is initially uncharged.
Learn more about the voltage here:
brainly.com/question/31419278
#SPJ11
Assume that body temperatures of healthy adults are normally distributed with a mean of 99.03°F and a standard deviation of 0.68°F.
Part 1
a. What percentage of adults have body temperatures greater than 100.12°F?
(Round to two decimal places as needed.)
Part 2
b. What percentage of adults have body temperatures less than 98.55°F?
(Round to two decimal places as needed.)
Part 3
c. If hospital officials decide to conduct tests on any patients more than 2.5 standard deviations above or below the mean, what are the cutoff temperatures?The lower cutoff temperature is
(Round to two decimal places as needed.)
Part 4
What is the critical reading above which barometers will be rejected? The upper cutoff temperature is entered your response here°F.
(Round to two decimal places as needed.)
5.3% of adults have a greater body temperature than 100.12 °F. 2.3% of adults have a lesser body temperature than 100.12 °F using the Z-score.
Mean percentage = 99.03°F
Standard deviation = 0.68°F
The formula to calculate the Z-score is:
z = (x - μ) / σ
z = (100.12 - 99.03) / 0.68
z = 1.61
The area right to the Z- score value = 0.053
Therefore, we can conclude that 5.3% of adults have a greater body temperature than 100.12 °F.
Percentage of adults with body temperatures less than 98.55 °F can be calculated as:
z = (98.55 - 99.03) / 0.68
z = -0.71
The area left to the Z- score value = 0.238
Therefore, we can conclude that 2.3% of adults have a lesser body temperature than 100.12 °F.
If the standard deviations are above or below the mean, the cut-off temperature is:
To calculate the Upper cutoff temperature:
z = 2.5
x = μ + (z * σ)
x = 99.03 + (2.5 * 0.68)
x = 100.95 °F
To calculate the Lower cutoff temperature:
z = -2.5
x = μ + (z * σ)
x = 99.03 + (-2.5 * 0.68)
x = 97.11 °F
The upper cutoff temperature is 100.95 °F and the lower cutoff temperature is 97.11 °F.
To learn more about Z-Score
https://brainly.com/question/31871890
#SPJ4
If they land perfectly vertically on the wagon and need 5 seconds to grab all the gold and jump off the wagon, will they make it before the wagon goes over the cliff? You may assur that the thieves (their shoes) experience sufficient friction with the surface of the wagon, s they do not slide when they jump onto the wagon. For this part use the impulse- momentum approach. Make sure to identify the system and follow the exact analyses and calculational procedures from the lectures.
Yes, the thieves will make it before the wagon goes over the cliff if the magnitude of the change in momentum is greater than or equal to the momentum of the wagon.
Will the thieves make it before the wagon goes over the cliff if the magnitude of the change in momentum is greater than or equal to the momentum of the wagon?To determine if the thieves will make it before the wagon goes over the cliff, compare the magnitude of the change in momentum (-(m + M) * v) with the momentum of the wagon (M * v).
If the change in momentum is greater than or equal to the wagon's momentum, the thieves will make it.
Learn more about momentum of the wagon.
brainly.com/question/32848525
#SPJ11
A point charge qı = 3.55 nC is located on the x-axis at r = 2.05 m, and a second point charge q2 = -5.70 nC is on the y-axis at y = 1.30 m. What is the total electric flux due to these two point charges through a spherical surface centered at the origin and with radius Ti = 0.680 m2 What is the total electric flux due to these two point charges through a spherical surface centered at the origin and with radius r2 = 1.65 m?
To calculate the total electric flux, we need to know the value of ε₀, which is the permittivity of free space and is approximately 8.854 x 10^-12 C²/(N·m²).
Substitute the given values and calculate the total electric flux for each case.
To calculate the total electric flux due to the two point charges through a spherical surface, we can use Gauss's law. Gauss's law states that the total electric flux through a closed surface is equal to the total charge enclosed by that surface divided by the permittivity of free space (ε₀).
- Point charge q₁ = 3.55 nC located on the x-axis at r = 2.05 m
- Point charge q₂ = -5.70 nC located on the y-axis at y = 1.30 m
- Radius r₁ = 0.680 m (for the first spherical surface)
- Radius r₂ = 1.65 m (for the second spherical surface)
Let's calculate the total electric flux through the spherical surface with radius r₁:
For q₁:
The electric flux due to q₁ is given by the equation Φ₁ = (q₁ / ε₀), as it is the only charge enclosed by the spherical surface.
For q₂:
The electric flux due to q₂ is zero because q₂ is not enclosed by the spherical surface.
Therefore, the total electric flux through the spherical surface with radius r₁ is Φ₁ = (q₁ / ε₀).
Now, let's calculate the total electric flux through the spherical surface with radius r₂:
For q₁:
The electric flux due to q₁ is given by the equation Φ₁ = (q₁ / ε₀), as it is the only charge enclosed by the spherical surface.
For q₂:
The electric flux due to q₂ is given by the equation Φ₂ = (q₂ / ε₀), as it is the only charge enclosed by the spherical surface.
Therefore, the total electric flux through the spherical surface with radius r₂ is Φ₂ = Φ₁ + Φ₂ = (q₁ / ε₀) + (q₂ / ε₀).
To calculate the total electric flux, we need to know the value of ε₀, which is the permittivity of free space and is approximately 8.854 x 10^-12 C²/(N·m²). Substitute the given values and calculate the total electric flux for each case.
Visit here to learn more about total electric flux brainly.com/question/30714188
#SPJ11
True or False: Both the North and South Poles of the Earth are located within continents, True False
False The North Pole is located in the Arctic Ocean and it is covered by sea ice. The South Pole is located on the continent of Antarctica.
Therefore, both the North and South Poles of the Earth are not located within continents.False is the answer to the question which states "Both the North and South Poles of the Earth are located within continents, True False".
The Earth is the only known planet that is capable of supporting life because of its ideal distance from the sun, the presence of water, and other essential factors. The North Pole and South Pole are two of the Earth's most intriguing places. Both of these are found at the Earth's ends and are located at 90 degrees north and south latitudes respectively.
To know more about covered visit:
https://brainly.com/question/14852650
#SPJ11
An object with mass 29 kg is placed 8.6 m below the ground. What is the gravitational potential energy of the object in the unit of J? Set the reference point of the height at the ground, i.e., h= 0 m at the ground, and use g=10 m/s 2
for the acceleration due to gravity.
The gravitational potential energy of an object can be calculated using the equation E = mgh,
where E is the gravitational potential energy, m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object relative to the reference point.
In this case, the mass of the object is given as 29 kg and it is placed 8.6 m below the ground. Since the reference point is set at the ground (h=0 m), the height of the object is -8.6 m. Substituting these values into the equation,
we have E = (29 kg)(10 m/s^2)(-8.6 m).
Calculating this expression will give us the gravitational potential energy of the object in joules (J). The negative sign indicates that the object has a negative potential energy due to its position below the reference point.
To know more about gravitational potential energy click here: brainly.com/question/3910603
#SPJ11
I
9. The wave equation for a semi-infinite string. Separate variables in the wave equation \[ \frac{1}{c^{2}} \frac{\partial^{2} u}{\partial t^{2}}-\frac{\partial^{2} u}{\partial x^{2}}=0 \] and solve i
The general solution to the wave equation is:
[tex]\[ u(x, t) = X(x)T(t)\\= (C\cos(kx) + D\sin(kx))(A\cos(\omega t) + B\sin(\omega t)). \][/tex]
To separate variables in the wave equation
[tex]\[ \frac{1}{c^2} \frac{\partial^2 u}{\partial t^2} - \frac{\partial^2 u}{\partial x^2} = 0, \][/tex]
we assume a separable solution of the form:
[tex]\[ u(x, t) = X(x)T(t). \][/tex]
Substituting this into the wave equation, we have:
[tex]\[ \frac{1}{c^2} \frac{\partial^2}{\partial t^2}(X(x)T(t)) - \frac{\partial^2}{\partial x^2}(X(x)T(t)) = 0. \][/tex]
Now we can separate the variables by dividing both sides of the equation by [tex]\(X(x)T(t)\)[/tex] and rearranging:
[tex]\[ \frac{1}{c^2} \frac{1}{T(t)} \frac{\partial^2 T(t)}{\partial t^2} - \frac{1}{X(x)} \frac{\partial^2 X(x)}{\partial x^2} = 0. \][/tex]
Since the left side only depends on [tex]\(t\)[/tex] and the right side only depends on [tex]\(x\)[/tex], both sides must be constant. Let's denote this constant by [tex]\(-\omega^2\)[/tex].
So we have two separate equations:
[tex]\[ \frac{1}{c^2} \frac{\partial^2 T(t)}{\partial t^2} + \omega^2 T(t) = 0, \]\\\\\frac{\partial^2 X(x)}{\partial x^2} + \omega^2 X(x) = 0. \][/tex]
The first equation is a simple harmonic oscillator equation, which has a general solution of the form:
[tex]\[ T(t) = A\cos(\omega t) + B\sin(\omega t), \][/tex]
where [tex]\(A\)[/tex] and [tex]\(B\)[/tex] are constants.
The second equation is also a simple harmonic oscillator equation, which has a general solution of the form:
[tex]\[ X(x) = C\cos(kx) + D\sin(kx), \][/tex]
where [tex]\(C\)[/tex] and [tex]\(D\)[/tex] are constants, and [tex]\(k = \omega/c\)[/tex] is the wave number.
Therefore, the general solution to the wave equation is:
[tex]\[ u(x, t) = X(x)T(t)\\= (C\cos(kx) + D\sin(kx))(A\cos(\omega t) + B\sin(\omega t)). \][/tex]
This is the separated solution of the wave equation. The constants [tex]\(A\)[/tex], [tex]\(B\)[/tex], [tex]\(C\)[/tex], and [tex]\(D\)[/tex] can be determined by applying appropriate initial or boundary conditions.
Know more about variables:
https://brainly.com/question/15078630
#SPJ4
True or False The flow of leachate in cubic feet per second from a discharge point in a landfill leachate collection system under cell A having hydraulic conductivity of 3.3 X 10 -5 ft/second will be greater than the flow of leachate from a discharge point in a landfill leachate collection system under cell B having a hydraulic conductivity of 3.2 X 10-4ft/second.
The flow of leachate will be greater in cell B than in cell A because cell B has a higher hydraulic conductivity.So the statement is False.
The flow of leachate in a landfill leachate collection system is directly proportional to the hydraulic conductivity of the soil or material through which it flows. The higher the hydraulic conductivity, the greater the flow rate. In this case, cell B has a higher hydraulic conductivity (3.2 × 10^(-4) ft/second) compared to cell A (3.3 × 10^(-5) ft/second).
It is important to note that hydraulic conductivity represents the ability of a porous medium (such as soil) to transmit water. A higher hydraulic conductivity indicates better permeability and easier flow of fluid. In the given scenario, the hydraulic conductivity of cell B is higher than that of cell A, indicating that leachate can flow more easily and at a greater rate in cell B compared to cell A.
To know more about hydraulic conductivity ,
https://brainly.com/question/29564643
#SPJ11
A 100 kg car is at rest at point A. It rolls down a frictionless track and reaches the other side of the hill at position D. The system is made up of the car, track and Earth. Use g = 10 m/s to simplify the values. Height (m) 30 20 10 a) Calculate the gravitational potential energy of the car at point A. Show all work. b) Calculate the kinetic energy at point C. Show all work, Calculate the velocity at point C. Show all work. d) At point D, the car is at a height of 20 m above the ground. If the car is only moving at 8 m/s when it reaches point D, how much energy was converted into heat and sound? Show all work.
a) Potential energy at A: 30,000 J.
b) Kinetic Energy at C: 30,000 J, velocity: 24.5 m/s. c) the velocity at point C is 20 m/s. d) Energy converted at D: 10,000 J.
a) The gravitational potential energy (PE) of an object is given by the formula PE = mgh, where m is the mass, g is the acceleration due to gravity, and h is the height.
In this case, the mass of the car is 100 kg and the height at point A is 30 m. Substituting these values, we get:
PE = 100 kg * 10 m/s^2 * 30 m = 30,000 J.
Therefore, the gravitational potential energy of the car at point A is 30,000 Joules.
b) The kinetic energy (KE) of an object is given by the formula KE = (1/2)mv^2, where m is the mass and v is the velocity.
At point C, the car has reached the bottom of the hill and all its potential energy has been converted into kinetic energy. Since the track is frictionless, there is no energy loss. Therefore, the kinetic energy at point C is equal to the initial potential energy at point A.
Using the given values, we can calculate the kinetic energy at point C:
KE = 30,000 J.
To find the velocity at point C, we can use the formula for kinetic energy and rearrange it to solve for v:
KE = (1/2)mv^2,
30,000 J = (1/2) * 100 kg * v^2,
v^2 = 600 m^2/s^2,
v ≈ 24.5 m/s.
Therefore, the kinetic energy at point C is 30,000 Joules, and the velocity at point C is approximately 24.5 m/s.
(c) Mass of the car (m) = 100 kg
Acceleration due to gravity (g) = 10 m/s²
Height at point C (h) = 10 m
KE at point C = 30,000 J - 100 kg * 10 m/s² * 10 m
KE at point C = 30,000 J - 10,000 J
KE at point C = 20,000 J
To calculate the velocity at point C, we can use the formula for kinetic energy:
KE at point C = 0.5mv²
Rearranging the formula to solve for velocity (v):
v² = (2 * KE at point C) / m
v² = (2 * 20,000 J) / 100 kg
v² = 40,000 J / 100 kg
v² = 400 m²/s²
Taking the square root of both sides:
v = √400 m²/s²
v = 20 m/s
Therefore, the velocity at point C is 20 m/s.
d) To calculate the amount of energy converted into heat and sound at point D, we need to find the difference in energy between point C and point D.
Using the formula for potential energy, we can find the potential energy at point D:
PE = mgh,
PE = 100 kg * 10 m/s^2 * 20 m = 20,000 J.
The initial kinetic energy at point C is 30,000 J. Therefore, the difference in energy is:
Energy difference = Initial kinetic energy - Potential energy at point D,
Energy difference = 30,000 J - 20,000 J = 10,000 J.
Hence, 10,000 Joules of energy were converted into heat and sound at point D.
Learn more about Potential energy click here :brainly.com/question/1242059
#SPJ11
A white pool ball moving horizontally at a speed of v 0
=3 m/s to the right and hits a red pool ball, initially at rest, of equal mass. The red pool ball goes into a pocket, which is at an angle of θ 1
=32 ∘
with respect to the horizontal. Assume that the collision is elastic (and hence the sum of the two final angles add up to 90 degrees). (a) Write down the two equations representing the law of conservation of momentum in the x and y directions. (b) Write down the equation representing the law of conservation of energy. (c) Use the equations in part (a) and (b) to find the final speed of the red ball (v 1
= ?). d) Use the previous parts to find the final speed of the white ball (v 2
=?). e) If the red ball travels 1.2 m to fall in the pocket, for how long did the red ball travel after the collision?
In the given scenario, a white pool ball with an initial horizontal speed of v₀ = 3 m/s collides with a red pool ball at rest. The red ball goes into a pocket at an angle of θ₁ = 32° with respect to the horizontal.
The collision is assumed to be elastic. The task is to write down the equations representing the conservation of momentum and energy, and then use these equations to find the final speed of the red ball (v₁), the final speed of the white ball (v₂), and the time it takes for the red ball to travel 1.2 m after the collision.
(a) Conservation of momentum in the x-direction: m₀v₀ = m₁v₁x + m₂v₂x
Conservation of momentum in the y-direction: 0 = m₁v₁y + m₂v₂y
Here, m₀ and m₁ represent the masses of the white and red balls, respectively, v₀ is the initial velocity of the white ball, and v₁x, v₁y, v₂x, and v₂y are the final velocities in the x and y directions.
(b) Conservation of energy: ½m₀v₀² = ½m₁v₁² + ½m₂v₂²
(c) Using the momentum equations, we can solve for v₁ and v₂.
(d) Substituting the values obtained in part (c) into the energy equation, we can solve for v₂.
(e) To find the time taken by the red ball to travel 1.2 m, we can use the equation d = v₁ * t, where d is the distance and t is the time.
To know more about conservation of momentum click here : brainly.com/question/29220242
#SPJ11
The time of travel for the red ball after the collision can also be calculated if the horizontal distance it travels is given as 1.2 m.
(a) The law of conservation of momentum states that the total momentum before the collision is equal to the total momentum after the collision. In the x-direction, where the motion is horizontal, the momentum conservation equation is:
m_white * v_0 = m_red * v_1x
In the y-direction, where the motion is vertical, the initial momentum is zero, and after the collision, only the red ball has momentum. Therefore, the momentum conservation equation is:
0 = m_red * v_1y
(b) The law of conservation of energy states that the total energy before the collision is equal to the total energy after the collision. In this case, the only form of energy involved is kinetic energy. Therefore, the equation representing the conservation of energy is:
1/2 * m_white * (v_0)^2 = 1/2 * m_red * (v_1)^2
(c) By using the momentum conservation equation in the x-direction and the equation representing the conservation of energy, we can solve for the final speed of the red ball, v_1.
(d) To find the final speed of the white ball, v_2, we can use the equation of conservation of momentum in the x-direction and substitute the value of v_1 obtained in part (c).
(e) To determine the time of travel for the red ball after the collision, we can use the horizontal distance traveled, 1.2 m, and the horizontal component of the velocity, v_1x, to calculate the time using the equation:
t = d / v_1x
To know more about conservation of momentum click here : brainly.com/question/29220242
#SPJ11
The voltage difference across an inductor in a DC circuit
1. is negative
2. is positive
3. zero
4. lags the current
(a) The voltage difference across an inductor in a DC circuit can be zero or positive.
(b) In a DC circuit, the voltage difference across an inductor can be zero if the current is constant or changing very slowly. This occurs when the inductor has reached a steady state, and the rate of change of current is negligible.
However, if the current is changing, the voltage difference across the inductor will be positive. According to Faraday's law of electromagnetic induction, when the current through an inductor changes, it induces a voltage across the inductor that opposes the change.
Inductive reactance in AC circuits can cause a phase shift between voltage and current, but in a DC circuit, the voltage across an inductor is either zero or positive.
Learn more about voltage difference here: brainly.com/question/3608538
#SPJ11
A uniform pipe of 2.0 kg is a right cylinder which outer radius is 4.0 cm and inner radius is 3.0 cm. What is the moment of inertia of
The moment of inertia of a uniform pipe can be calculated using the formula for the moment of inertia of a hollow cylinder. The moment of inertia depends on the mass distribution and the geometry of the object.
In this case, we are given that the pipe has a mass of 2.0 kg and outer radius of 4.0 cm (0.04 m) and inner radius of 3.0 cm (0.03 m).
The formula for the moment of inertia of a hollow cylinder is I = (1/2) * m * (r_outer^2 + r_inner^2), where m is the mass and r_outer and r_inner are the outer and inner radii, respectively.
Substituting the given values into the formula, we have I = (1/2) * 2.0 kg * ((0.04 m)^2 + (0.03 m)^2).
Calculating the expression inside the parentheses, we get I = (1/2) * 2.0 kg * (0.0016 m^2 + 0.0009 m^2).
Simplifying further, we have I = (1/2) * 2.0 kg * 0.0025 m^2.
Finally, calculating the result, we find that the moment of inertia of the uniform pipe is 0.0025 kg·m^2.
To know more about moment of inertia click here: brainly.com/question/30051108
#SPJ11
What is the torque about the origin on a particle posi- tioned at r = (3.0 m) i – (1.0 m)j – (5.0 m)k, exerted by a force of — F = (2.0 N)i + (4.0 N)j + (3.0 N)k?
The torque about the origin on a particle can be calculated by taking the cross product of the position vector and the force vector.
Given the position vector
r = (3.0 m)i - (1.0 m)j - (5.0 m)k
and the force vector F = (2.0 N)i + (4.0 N)j + (3.0 N)k,
we can determine the torque exerted on the particle.
The torque exerted on a particle is given by the formula τ = r × F,
where τ represents the torque, r is the position vector, and F is the force vector.
In this case, the position vector is
r = (3.0 m)i - (1.0 m)j - (5.0 m)k and
the force vector is F = (2.0 N)i + (4.0 N)j + (3.0 N)k.
We can calculate the torque by taking the cross product of these vectors.
By performing the cross product,
we have
τ = [(1.0 m)(3.0 N) - (-5.0 m)(4.0 N)]i - [(3.0 m)(2.0 N) - (-5.0 m)(3.0 N)]j + [(3.0 m)(4.0 N) - (1.0 m)(2.0 N)]k.
Simplifying this expression will give us the torque about the origin on the particle.
To know more about torque click here :
brainly.com/question/30338175
#SPJ11
A proton follows a circular path of radius 20cm in a magnetic field 0.3T uniform. Calculate the speed of the proton. Charge of the proton is 1.6x10-19 C and mass of the proton is 1.6x10-27kg.
We are asked to calculate the speed of the proton, given its charge and mass. The speed of the proton can be determined by balancing the magnetic force and the centripetal force acting on it.
The magnetic force on a charged particle moving in a magnetic field is given by the equation F = q * v * B, where F is the force, q is the charge, v is the velocity of the particle, and B is the magnetic field strength. In this case, the force is provided by the centripetal force required to keep the proton moving in a circular path.
The centripetal force is given by the equation F = (m * v²) / r, where m is the mass of the proton, v is its velocity, and r is the radius of the circular path. By equating the magnetic force and the centripetal force, we can solve for the velocity of the proton. So we have q * v * B = (m * v²) / r. Rearranging the equation, we get v = (q * B * r) / m.
Substituting given values, we have v = (1.6 x 10^-19 C * 0.3 T * 0.2 m) / (1.6 x 10^-27 kg). Calculating this expression will give us the speed of the proton.
To learn more about centripetal force click here : brainly.com/question/14021112
#SPJ11
A lightweight bumper car (mass = 200 kg) initially traveling at 6 m/sec to the right collides into a heavier bumper car (mass = 400 kg). The heavier bumper car is initially at rest. The lighter bumper car recoils backwards (to the left) after the collision at a speed of 1 m/sec. a) Draw the momentum vectors before the collision. b) Draw the momentum vectors after the collision. c) What is the forward speed of the heavier bumper car after the collision? d) How much heat was generated in the collision?
a) Before collision: Lighter car (200 kg, 6 m/s right), Heavier car (400 kg, 0 m/s). b) After collision: Lighter car (200 kg, 1 m/s left), Heavier car (400 kg, 3.5 m/s right). c) Heavier car's forward speed after collision: 3.5 m/s.
a) Before the collision:
Lighter Bumper Car (200 kg, 6 m/s to the right): -----> (momentum vector)
Heavier Bumper Car (400 kg, 0 m/s): No momentum vector (at rest)
b) After the collision:
Lighter Bumper Car (200 kg, 1 m/s to the left): <----- (recoiling momentum vector)
Heavier Bumper Car (400 kg, v m/s to the right): -----> (forward momentum vector)
c) To find the forward speed of the heavier bumper car after the collision, we can use the principle of conservation of momentum. The total momentum before the collision is equal to the total momentum after the collision:
(200 kg * 6 m/s) + (400 kg * 0 m/s) = (200 kg * -1 m/s) + (400 kg * v m/s)
Simplifying the equation:
1200 kg·m/s = -200 kg·m/s + 400 kg·v
Rearranging and solving for v:
v = (1200 kg·m/s + 200 kg·m/s) / 400 kg
v = 1400 kg·m/s / 400 kg
v = 3.5 m/s
Therefore, the forward speed of the heavier bumper car after the collision is 3.5 m/s.
d) To calculate the heat generated in the collision, we need additional information such as the coefficient of restitution or any other factors affecting the energy transfer. Without this information, it is not possible to determine the exact amount of heat generated in the collision.
know more about coefficient of restitution here: brainly.com/question/32546084
#SPJ11
A point source generates a wave which radiates in all directions (radially, in the shape
of a sphere). How does the intensity change as the wave moves away from the source?
A. increases as r
B. remains the same
C. decreases as r (that is, varies as 1/r)
D. decreases as r^2 (that is, varies as 1/r^2)
As a wave radiates from a point source in all directions, the intensity decreases as the wave moves away from the source. The intensity varies as 1/r^2, where r represents the distance from the source.
The intensity of a wave is defined as the power per unit area perpendicular to the direction of wave propagation. When a wave radiates from a point source, it spreads out in the shape of a sphere, with the source at the center. The surface area of a sphere increases as the square of its radius.
Since the same amount of power is spread over a larger surface area as the wave expands, the intensity of the wave decreases with increasing distance from the source. Mathematically, the relationship between intensity and distance can be described using the inverse square law.
According to the inverse square law, the intensity of the wave varies inversely with the square of the distance from the source. This means that as the distance (r) increases, the intensity decreases as 1/r^2. Therefore, the correct answer is option D) decreases as r^2 (that is, varies as 1/r^2).
To learn more about wave Click Here: brainly.com/question/25954805
#SPJ11
