Each electron winds up with kinetic energy of
(270 keV)
plus
(whatever KE it had when it started accelerating).
A 5.0 kg block hangs from a spring with spring constant 2000 N/m. The block is pulled down 5.0 cm from the equilibrium position and given an initial velocity of 1.0 m/s back towards equilibrium. a) What is the total mechanical energy of the motion
Answer:
Explanation:i think this would help u
The magnetic field of a plane-polarized electromagnetic wave moving in the z-direction is given by in SI units. What is the frequency of the wave
Complete Question
The magnetic field of a plane-polarized electromagnetic wave moving in the z-direction is given by
[tex]B=1.2* 10^{-6} sin [2\pi[(\frac{z}{240} ) - ( \frac{t * 10^7}{8} ) ] ][/tex] in SI units.
Answer:
The value is [tex]f = 1.98918*10^{5}\ Hz[/tex]
Explanation:
From the question we are told that
The magnetic field is [tex]B=1.2* 10^{-6} sin [2\pi[(\frac{z}{240} ) - ( \frac{t * 10^7}{8} ) ] ][/tex]
This above equation can be modeled as
[tex]B=1.2* 10^{-6} sin [2\pi[(\frac{z}{240} ) - ( \frac{t * 10^7}{8} ) ] ] \equiv A sin ( kz -wt )[/tex]
So
[tex]w = \frac{10^7}{8}[/tex]
Generally the frequency is mathematically represented as
[tex]f = \frac{w}{2 \pi}[/tex]
=> [tex]f = \frac{ \frac{10^7}{8} }{2 \pi}[/tex]
=> [tex]f = 1.98918*10^{5}\ Hz[/tex]
A race-car drives around a circular track of radius RRR. The race-car speeds around its first lap at linear speed v_iv i v, start subscript, i, end subscript. Later, its speed increases to 4v_i4v i 4, v, start subscript, i, end subscript. How does the magnitude of the car's centripetal acceleration change after the linear speed increases
Answer:
The magnitude of the centripetal acceleration increases by 16 times when the linear speed increases by 4 times.
Explanation:
The initial centripetal acceleration, a of the race-car around the circular track of radius , R with a linear speed v is a = v²/R.
When the linear speed of the race-car increases to v' = 4v, the centripetal acceleration a' becomes a' = v'²/R = (4v)²/R = 16v²/R.
So the centripetal acceleration, a' = 16v²/R.
To know how much the magnitude of the car's centripetal acceleration changes, we take the ratio a'/a = 16v²/R ÷ v²/R = 16
a'/a = 16
a' = 16a.
So the magnitude of the centripetal acceleration increases by 16 times when the linear speed increases by 4 times.
Consider two parallel wires where the magnitude of the left currentis 2 I0(io) and that of the right current is I0(io). Point A is midway between the wires,and B is an equal distance on the other side of the wires.
The ratio ofthe magnitude of the magnetic field at point A to that at point Bis________
Answer:
Explanation:
At the point midway between wires
magnetic field due to wire having current 2I₀
= 10⁻⁷ x 2 x2I₀ / r where 2r is the distance between wires .
magnetic field due to wire having current I₀
= 10⁻⁷ x 4 I₀ / r
magnetic field due to wire having current I₀
= 10⁻⁷ x 2I₀ / r
= 10⁻⁷ x 2 I₀ / r where 2r is the distance between wires .
these fields are in opposite direction as direction of current is same in both .
net magnetic field = (4 - 2 )x 10⁻⁷ x I₀ / r
= 2 x 10⁻⁷ x I₀ / r
At point A net magnetic field = 2 x 10⁻⁷ x I₀ / r
At point B , we shall calculate magnetic field
magnetic field due to nearer wire having current 2 I₀ = 10⁻⁷ x 4 I₀ / r
magnetic field due to wire far away = 10⁻⁷ x 2 I₀ / 3r
These magnetic fields act in the same direction so they will add up
net magnetic field = [ (4 I₀ / r) + (2 I₀ / 3r) ] x 10⁻⁷
= (14 I₀ / 3r ) x 10⁻⁷
Magnetic field at point B = (14 I₀ / 3r ) x 10⁻⁷
Ratio of field at A and B
= 3 / 7 . Ans
The ratio of the magnitude of the magnetic field at point A to point B is :
3 / 7
Given data :
Magnitude of the left current is 2I₀
Magnitude of the right current is I₀
First step : Determine the magnetic field at point A
The magnetic field due to the left current ( 2I₀ )
10⁻⁷ * 2 * 2I₀ / r ( 2r = distance between wires )
The magnetic field due to the right current ( I₀ )
10⁻⁷ * 2 I₀ / r
From the expressions above the magnetic fields are in opposite direction
∴ Net magnetic field = (4 - 2 )* 10⁻⁷ * I₀ / r = 2 * 10⁻⁷ * I₀ / r
Hence The magnetic field at point A = 2 * 10⁻⁷ * I₀ / r
Next step : determine the magnetic field at point B
Magnetic field due to the closest wire to point B ( i.e.2I₀ ) = 10⁻⁷ * 4 I₀ / r
Magnetic field due to the wire away from point A = 10⁻⁷ * 2 I₀ / 3r
Since the fields acts in the same directions
The net magnetic field = (4 I₀ / r) + (2 I₀ / 3r) ] * 10⁻⁷ = ( 14 I₀ / 3r ) * 10⁻⁷
Hence The magnetic field at point A = ( 14 I₀ / 3r ) * 10⁻⁷
Therefore the ratio of the magnitude of the magnetic field at point A to point B = 3/ 7
Hence we can conclude that the ratio of the magnitude of the magnetic field at point A to point B = 3 / 7
Learn more : https://brainly.com/question/22403676
When the electron is moving in the plane of the page in the direction indicated by the arrow, the force on the electron is directed:_____
a. into the page.
b. toward the left
c. toward the right
d. toward the bottom of the page.
e. toward the top of the page.
f. out of the page.
Answer: F
Out of the page.
Explanation:
For an electron with a charge of -e, the magnitude of the force on it is F = BeV
Where
F = force on the electron
e = charge ( electrons )
V = velocity
B = magnetic field
F is the force acting on all the electrons in a wire which gives rise to the F = BIL
Where
I = current
L = length of the wire
The force F is always at the right angle to the particle's velocity and its direction can be found using the left hand rule.
When the electron is moving in the plane of the page in the direction indicated by the arrow, the force on the electron is directed out of the page.
Given a double slit apparatus with slit distance 2 mm, what is the theoretical maximum number of bright spots that I would see when I shine light with a wavelength 500 nm on the slits
Answer:
The values is [tex]m_{max} = 8001 \ bright \ spots[/tex]
Explanation:
From the question we are told that
The slit distance is [tex]d = 2 \ mm = 2*10^{-3} \ m[/tex]
The wavelength is [tex]\lambda = 500 \ nm = 500 *10^{-9} \ m[/tex]
At the first half of the screen from the central maxima
The number of bright spot according to the condition for constructive interference is
[tex]n = \frac{d * sin (\theta )}{\lambda}[/tex]
For maximum number of spot [tex]\theta = 90^o[/tex]
So
[tex]n = \frac{2*10^{-3} * sin (90 )}{500 *10^{-9}}[/tex]
[tex]n =4000[/tex]
Now for the both sides plus the central maxima we have
[tex]m_{max} = 2 * n + 1[/tex]
substituting values
[tex]m_{max} = 2 * 4000 + 1[/tex]
[tex]m_{max} = 8001 \ bright \ spots[/tex]
We can reasonably model a 75 W incandescent light bulb as a sphere 6.0 cm in diameter. Typically only about 5% of the energy goes to visible light; the rest goes largely to non-visible infrared radiation. (a) What is the visible light intensity at the surface of the bulb
Answer:
Visible light intensity at the surface of the bulb (I) = 331 W/m²
Explanation:
Given:
Energy = 75 W
Radius = 6 /2 = 3 cm = 3 × 10⁻² m
Energy goes to visible light = 5% = 0.05
Find:
Visible light intensity at the surface of the bulb (I)
Computation:
Visible light intensity at the surface of the bulb (I) = P / 4A
Visible light intensity at the surface of the bulb (I) = (0.05)(75) / 4π(3 × 10⁻²)²
Visible light intensity at the surface of the bulb (I) = 3.75 / 4π(9 × 10⁻⁴)
Visible light intensity at the surface of the bulb (I) = 331 W/m²
In an adiabatic process:
a. the energy absorbed as heat equals the work done by the systemon its environment
b. the energy absorbed as heat equals the work done by theenvironment on the system
c. the work done by the environment on the system equals the changein internal energy
Answer:
c. the work done by the environment on the system equals the changein internal energy.
Explanation:
Adiabatic process:
When the boundary of a system is perfectly insulated, it means that the energy can not flow from the system and into the system ,these system is known as adiabatic system.
When the energy transfer in the system is zero ,then these type of process is known as adiabatic process.
From the first law of thermodynamics
Q= ΔU + W
Q=Heat transfer
ΔU=Change in internal energy
W=Work transfer
In adiabatic process , Q= 0
Therefore
0=ΔU +W
W=- ΔU
Negative sign indicates that ,the work done by the environment.
Therefore the correct option will be (c).
In Young's experiment a mixture of orange light (611 nm) and blue light (471 nm) shines on the double slit. The centers of the first-order bright blue fringes lie at the outer edges of a screen that is located 0.497 m away from the slits. However, the first-order bright orange fringes fall off the screen. By how much and in what direction (toward or away from the slits) should the screen be moved, so that the centers of the first-order bright orange fringes just appear on the screen
Answer:
0.5639m
Explanation:
For a young double slit experiment the expression below gives the angular separation for m dark fringe having slit width d and wavelength λ
=sin⁻¹(mλ/d)
mλ /d =y/L
for the first order,
y= mλL/d
For ratio separation y₀/yD=1 and d= 1
y₀/yD= [mλ ₀L₀/d]/[mλD.LD./d]
1=λ ₀L₀/λD.LD.
λD.LD= λ ₀L₀
L₀= λD.LD/ λ ₀..............(1)
Then substitute the given values into (1) we have
L₀=471 *0.497/611
= 0.3831m
Distance by which the screen has to be moved towards the slit is
LD- Lo
0.947-0.3831= 0.5639m
A system gains 767 kJ of heat, resulting in a change in internal energy of the system equal to +151 kJ. How much work is done?
Answer:
The work done on the system is -616 kJ
Explanation:
Given;
Quantity of heat absorbed by the system, Q = 767 kJ
change in the internal energy of the system, ΔU = +151 kJ
Apply the first law of thermodynamics;
ΔU = W + Q
Where;
ΔU is the change in internal energy
W is the work done
Q is the heat gained
W = ΔU - Q
W = 151 - 767
W = -616 kJ (The negative sign indicates that the work is done on the system)
Therefore, the work done on the system is -616 kJ
You are holding on to one end of a long string that is fastened to a rigid steel light pole. After producing a wave pulse that was 5 mm high and 4 em wide, you want to produce a pulse that is 4 cm wide but 7 mm high. You must move your hand up and down once,
a. a smaller distance up, but take a shorter time.
b. the same distance up as before, but take a shorter time.
c. a greater distance up, but take a longer time.
d. the same distance up as before, but take a longer time.
e. a greater distance up, but take the same time.
Answer:
It will take. the same distance up as before, but take a longer time
What is the average value of the magnitude of the Poynting vector (intensity) at 1 meter from a 100-watt light bulb radiating in all directions
Answer:
I = 7.96 W / m²
Explanation:
The light bulb emits a power of P = 100W, this power is distributed over the surface of a sphere, thus the emission is in all directions.
Intensity is defined by power per unit area
I = P / A
The area of a sphere is
A = 4π r²
we substitute
I = P / (4π r²)
in this case it tells us that the distance is r = 1 m
let's calculate
I = 100 / (4π 1²)
I = 7.96 W / m²
please help !!!!!!!!!!
Answer:
Lighthouse 1 during the day will be warmer, lighthouse 2 during the night will be warmer.
Explanation:
As the paragraph stated land absorbs heat and heats up faster than water. So during the day the lighthouse farthest away from the water will be hotter. But then the converse is true also land losses heat faster than water at night. So the water retains the heat from the day better making the lighthouse by the water warmer at night.
Determine the next possible thickness of the film (in nm) that will provide the proper destructive interference. The index of refraction of the glass is 1.58 and the index of refraction of the film material is 1.48.
Answer:
I know the answer
Explanation:
We want to choose the film thickness such that destructive interference occurs between the light reflected from the air-film interface (call it wave 1) and from the film-lens interface (call it wave 2). For destructive interference to occur, the phase difference between the two waves must be an odd multiple of half-wavelengths.
You can think of the phases of the two waves as second hands on a clock; as the light travels, the hands tick-tock around the clock. Consider the clocks on the two waves in question. As both waves travel to the air-film interface, their clocks both tick-tock the same time-no phase difference. When wave 1 is reflected from the air-film boundary, its clock is set forward 30 seconds; i.e., if the hand was pointing toward 12, it's now pointing toward 6. It's set forward because the index of refraction of air is smaller than that of the film.
Now wave 1 pauses while wave two goes into and out of the film. The clock on wave 2 continues to tick as it travels in the film-tick, tock, tick, tock.... Clock 2 is set forward 30 seconds when it hits the film-lens interface because the index of refraction of the film is smaller than that of the lens. Then as it travels back through the film, its clock still continues ticking. When wave 2 gets back to the air-film interface, the two waves continue side by side, both their clocks ticking; there is no change in phase as they continue on their merry way.
So, to recap, since both clocks were shifted forward at the two different interfaces, there was no net phase shift due to reflection. There was also no phase shift as the waves travelled into and out from the air-film interface. The only phase shift occured as clock 2 ticked inside the film.
Call the thickness of the film t. Then the total distance travelled by wave 2 inside the film is 2t, if we assume the light entered pretty much normal to the interface. This total distance should equal to half the wavelength of the light in the film (for the minimum condition; it could also be 3/2, 5/2, etc., but that wouldn't be the minimum thickness) since the hand of the clock makes one revolution for each distance of one wavelength the wave travels (right?).
A hydraulic lift raises a 2 000-kg automobile when a 500-N force is applied to the smaller piston. If the smaller piston has an area of 10 cm2, what is the cross-sectional area of the larger piston
Answer:
The cross-sectional area of the larger piston is 392 cm²
Explanation:
Given;
output mass of the piston, m₀ = 2000 kg
input force of the piston, F₁ = 500 N
input area of the piston, A₁ = 10 cm² = 0.001 m²
The output force is given by;
F₀ = m₀g
F₀ = 2000 x 9.8
F₀ = 19600 N
The cross-sectional area of the larger piston or output area of the piston will be calculated by applying the following equations;
[tex]\frac{F_i}{A_i} = \frac{F_o}{A_o} \\\\A_o= \frac{F_o A_i}{F_i} \\\\A_o = \frac{19600*0.001}{500} \\\\A_o = 0.0392 \ m^2\\\\A_o = 392 \ cm^2[/tex]
Therefore, the cross-sectional area of the larger piston is 392 cm²
What is an understood decimal
Nuclear plants use radioactive fuel to produce steam which turns a turbine to generate electricity. This is an example of a(n) _____. A) heat pump B) heat mover C) internal combustion engine D) external combustion engine
Answer:
C) internal combustion engineExplanation:
You slip a wrench over a bolt. Taking the origin at the bolt, the other end of the wrench is at x=18cm, y=5.5cm. You apply a force F? =88i^?23j^ to the end of the wrench. What is the torque on the bolt?
Answer:
The torque on the wrench is 4.188 Nm
Explanation:
Let r = xi + yj where is the distance of the applied force to the origin.
Since x = 18 cm = 0.18 cm and y = 5.5 cm = 0.055 cm,
r = 0.18i + 0.055j
The applied force f = 88i - 23j
The torque τ = r × F
So, τ = r × F = (0.18i + 0.055j) × (88i - 23j) = 0.18i × 88i + 0.18i × -23j + 0.055j × 88i + 0.055j × -23j
= (0.18 × 88)i × i + (0.18 × -23)i × j + (0.055 × 88)j × i + (0.055 × -22)j × j
= (0.18 × 88) × 0 + (0.18 × -23) × k + (0.055 × 88) × (-k) + (0.055 × -22) × 0 since i × i = 0, j × j = 0, i × j = k and j × i = -k
= 0 - 4.14k + 0.0484(-k) + 0
= -4.14k - 0.0484k
= -4.1884k Nm
≅ -4.188k Nm
So, the torque on the wrench is 4.188 Nm
Please help!
Much appreciated!
Answer:
F = 2.7×10¯⁶ N.
Explanation:
From the question given:
F = (9×10⁹ Nm/C²) (3.2×10¯⁹ C × 9.6×10¯⁹ C) /(0.32)²
Thus we can obtain the value value of F by carrying the operation as follow:
F = (9×10⁹) (3.2×10¯⁹ × 9.6×10¯⁹) /(0.32)²
F = 2.7648×10¯⁷ / 0.1024
F = 2.7×10¯⁶ N.
Therefore, the value of F is 2.7×10¯⁶ N.
Two hoops, staring from rest, roll down identical incline planes. The work done by nonconservative forces is zero. The hoops have the same mass, but the larger hoop has twice the radius. Which hoop will have the greater total kinetic energy at the bottom
Answer:
They both have the same total K.E at the bottom
Explanation:
This Is because If assuming no work is done by non conservative forces, total mechanical energy must be conserved
So
K1 + U1 = K2 + U2
But If both hoops start from rest, and and at the bottom of the incline the level for gravitational potential energy is zero for reference
thus
K1 = 0 , U2 = 0
ΔK = ΔU = m g. h
But if the two inclines have the same height, and both hoops have the same mass m,
So difference in kinetic energy, must be the same for both hoops.
Can you come up with a mathematical relationship, based on your data that shows the relationship between distance from the charges and electric field strength?
Answer:
Explanation:
This question appears incomplete because of the absence of the data been talked about in the question. However, there is a general ruling here and it can be applied to the data at hand.
If an increase in the distance of charges (let's denote with "d") causes the electric field strength (let's denote with"E") to increase, then the mathematical representation can be illustrated as d ∝ E (meaning distance of charge is directly proportional to electric field strength).
But if an increase in the distance of the charges causes the electric field strength to decrease, then the mathematical representation can be illustrated as d ∝ 1/E (meaning distance of charge is inversely proportional to electric field strength).
A scatterplot can also be used to determine this. If there is a positive correlation (correlation value is greater than zero but less than or equal to 1) on the graph, then it is illustrated as "d ∝ E" BUT if there is a negative correlation (correlation value is less than zero but greater than or equal to -1), then it can be illustrated as "d ∝ 1/E".
In a velocity selector having electric field E and magnetic field B, the velocity selected for positively charged particles is v= E/B. The formula is the same for a negatively charged particles.
a. True
b. False
Answer:
True or False
Explanation:
Because.....
easy 50% chance you are right
A fixed 11.2-cm-diameter wire coil is perpendicular to a magnetic field 0.53 T pointing up. In 0.10 s , the field is changed to 0.24 T pointing down. What is the average induced emf in the coil?
Answer:
The average induced emf in the coil is 0.0286 V
Explanation:
Given;
diameter of the wire, d = 11.2 cm = 0.112 m
initial magnetic field, B₁ = 0.53 T
final magnetic field, B₂ = 0.24 T
time of change in magnetic field, t = 0.1 s
The induced emf in the coil is calculated as;
E = A(dB)/dt
where;
A is area of the coil = πr²
r is the radius of the wire coil = 0.112m / 2 = 0.056 m
A = π(0.056)²
A = 0.00985 m²
E = -0.00985(B₂-B₁)/t
E = 0.00985(B₁-B₂)/t
E = 0.00985(0.53 - 0.24)/0.1
E = 0.00985 (0.29)/ 0.1
E = 0.0286 V
Therefore, the average induced emf in the coil is 0.0286 V
We have that for the Question, it can be said that the average induced emf in the coil is
E=0.028565V
From the question we are told
A fixed 11.2-cm-diameter wire coil is perpendicular to a magnetic field 0.53 T pointing up. In 0.10 s , the field is changed to 0.24 T pointing down. What is the average induced emf in the coil?
Generally the equation for the Average emf induced is mathematically given as
[tex]Emf_a=-NA\frac{dB}{dt}\\\\Where\\\\Area\\\\a=\pir^2\\\\a=\pi(0.056)^2\\\\a=0.00985\\\\[/tex]
Hence
[tex]dB=0.24-0.53\\\\dB=-0.29T[/tex]
Therefore
[tex]E=-\frac{1*0.00985*-0.29 }{0.10}[/tex]
E=0.028565V
For more information on this visit
https://brainly.com/question/23379286
A mass M slides downward along a rough plane surface inclined at angle \Theta\:Θ= 32.51 in degrees relative to the horizontal. Initially the mass has a speed V_0\:V 0 = 6.03 m/s, before it slides a distance L = 1.0 m down the incline. During this sliding, the magnitude of the power associated with the work done by friction is equal to the magnitude of the power associated with the work done by the gravitational force. What is the coefficient of kinetic friction between the mass and the incline?
Answer: μ = 0.8885
Explanation: Force due to friction is calculated as: [tex]F_{f} = \mu.N[/tex]
At an inclined plane, normal force (N) is: N = mgcosθ, in which θ=32.51.
Power associated with work done by friction is [tex]P=F_{f}.x[/tex]. The variable x is displacement the object "spent its energy".
Power associated with work done by gravitational force is P = mghcosθ, where h is height.
The decline forms with horizontal plane a triangle as draw in the picture.
To determine force due to friction:
[tex]F_{f}.x=mghcos(\theta)[/tex]
[tex]F_{f}=\frac{mghcos(\theta)}{x}[/tex]
Replacing force:
[tex]\frac{m.g.h.cos(\theta)}{x} = \mu.m.g.cos(\theta)[/tex]
[tex]\mu=\frac{h}{x}[/tex]
Calculating h using trigonometric relations:
[tex]sin(32.51) = \frac{h}{1}[/tex]
h = sin(32.51)
Coefficient of Kinetic friction is
[tex]\mu=\frac{sin(32.51)}{1}[/tex]
μ = 0.8885
For these conditions, coefficient of kinetic friction is μ = 0.8885.
A viewing screen is separated from a double slit by 5.20 m. The distance between the two slits is 0.0300 mm. Monochromatic light is directed toward the double slit and forms an interference pattern on the screen. The first dark fringe is 3.70 cm from the center line on the screen.
Required:
a. Determine the wavelength of light.
b. Calculate the distance between the adjacent bright fringes.
Answer:
The wavelength of this light is approximately [tex]427\; \rm nm[/tex] ([tex]4.27\times 10^{-7}\; \rm m[/tex].)The distance between the first and central maxima is approximately [tex]7.40\; \rm cm[/tex] (about twice the distance between the first dark fringe and the central maximum.)Explanation:
WavelengthConvert all lengths to meters:
Separation of the two slits: [tex]0.0300\; \rm mm = 3.00\times 10^{-5}\; \rm m[/tex].Distance between the first dark fringe and the center of the screen: [tex]3.70\; \rm cm = 3.70\times 10^{-2}\; \rm m[/tex].Refer to the diagram attached (not to scale.) Assuming that the screen is parallel to the line joining the two slits. The following two angles are alternate interior angles and should be equal to each other:
The angle between the filter and the beam of light from the lower slit, andThe angle between the screen and that same beam of light.These two angles are marked with two grey sectors on the attached diagram. Let the value of these two angles be [tex]\theta[/tex].
The path difference between the two beams is approximately equal to the length of the segment highlighted in green. In order to produce the first dark fringe from the center of the screen (the first minimum,) the length of that segment should be [tex]\lambda / 2[/tex] (one-half the wavelength of the light.)
Therefore:
[tex]\displaystyle \cos \theta \approx \frac{\text{Path difference}}{\text{Slit separation}} = \frac{\lambda / 2}{3.00\times 10^{-5}\; \rm m}[/tex].
On the other hand:
[tex]\begin{aligned} \cot \theta &\approx \frac{\text{Distance between central peak and first minimum}}{\text{Distance between the screen and the slits}} \\ &= \frac{3.70\times 10^{-2}\; \rm m}{5.20\; \rm m} \approx 0.00711538\end{aligned}[/tex].
Because the cotangent of [tex]\theta[/tex] is very close to zero,
[tex]\cos \theta \approx \cot \theta \approx 0.00711538[/tex].
[tex]\displaystyle \frac{\lambda /2}{3.00\times 10^{-5}\; \rm m} \approx \cos\theta\approx 0.00711538[/tex].
[tex]\begin{aligned}\lambda &\approx 2\times 0.00711538 \times \left(3.00\times 10^{-5}\; \rm m\right) \\ &\approx 4.26 \times 10^{-7}\; \rm m = 426\; \rm nm\end{aligned}[/tex].
Distance between two adjacent maximaIf the path difference is increased by one wavelength, then the intersection of the two beams would move from one bright fringe to the next one.
The path difference required for the central maximum is [tex]0[/tex].The path difference required for the first maximum is [tex]\lambda[/tex].The path difference required for the second maximum is [tex]2\,\lambda[/tex].On the other hand, if the distance between the maximum and the center of the screen is much smaller than the distance between the screen and the filter, then:
[tex]\begin{aligned}&\frac{\text{Distance between image and center of screen}}{\text{Distance between the screen and the slits}} \\ &\approx \cot \theta \\ &\approx \cos \theta \\ &\approx \frac{\text{Path difference}}{\text{Slit separation}}\end{aligned}[/tex].
Under that assumption, the distance between the maximum and the center of the screen is approximately proportional to the path difference. The distance between the image (the first minimum) and the center of the screen is [tex]3.70\; \rm cm[/tex] when the path difference is [tex]\lambda / 2[/tex]. The path difference required for the first maximum is twice as much as that. Therefore, the distance between the first maximum and the center of the screen would be twice the difference between the first minimum and the center of the screen: [tex]2 \times 3.70\; \rm cm = 7.40\; \rm cm[/tex].
The temperature difference between the inside and the outside of a house on a cold winter day is 33°F. (a) Express this difference on the Celsius scale. 0.55 Incorrect: Your answer is incorrect. °C (b) Express this difference on the Kelvin scale. 273.7 Incorrect: Your answer is incorrect. K
Answer:
a) 0.56°C
b) 273.56 K
Explanation:
If we want to convert from Fahrenheit scale to Celcius scale we use the formula;
T(°C) = (T(°F) - 32) × 5/9
Where T(°F) = 33°F
Hence;
T(°C) = (33°F - 32) × 5/9
T°C = 0.56°C
b)
T(K) = T°C + 273
T(K) = 0.56 + 273
T(K) = 273.56 K
The highest mountain on mars is olympus mons, rising 22000 meters above the martian surface. If we were to throw an object horizontaly off the mountain top, how long would it take to reach the surface? (Ignore atmospheric drag forces and use gMars=3.72m/s^2
a. 2.4 minutes
b. 0.79 minutes
c. 1.8 minutes
d. 3.0 minutes
Answer:
t = 1.81 min , the correct answer is c
Explanation:
This is a missile throwing exercise
The object is thrown horizontally, so its vertical speed is zero (voy = 0), let's use the equation
y = y₀ + [tex]v_{oy}[/tex] t - ½ g t²
the final height is y = 0 and the initial height is y₀ = 22000 m
0 = y₀ + 0 - ½ g t²
t = √y 2y₀ / g
let's calculate
t = √(2 22000 / 3.72)
t = 108.76 s
let's reduce to minutes
t = 108.76 s (1 min / 60 s)
t = 1.81 min
The correct answer is c
In _____ research, a group of people of one age is compared to a group of people who are another age.
Answer:
cross-sectional
Explanation:
The full definition of this is ''a research design in which several different age-groups of participants are studied at one particular point in time.''
The molecules in Tyler are composed of carbon and other atoms that share one or more electrons between two atoms, forming what is known as a(n) _____ bond.
Answer:
covalent
Explanation:
covalent bonds share electrons
The base unit prefix used for 1,000× is _____. kilo milli centi deka
Answer:
[tex]\Large \boxed{\sf kilo}[/tex]
Explanation:
kilo is a prefix that means [tex]1000[/tex] of the base unit.
Answer:
kilo is the correct answer
Explanation:
because my exam says sooo....
