Answer:
When the circuit switch is off, no electricity will flow and then the circuit is called an open circuit. Electricity will not flow in open circuit.
Explanation:
A closed circuit has a complete path for current to flow. ... This can happen when two bare wires in a circuit touch each other. The part of the circuit bypassed by the short circuit ceases to function, and a large amount of current could start to flow. This can generate a lot of heat in the wires and cause a fire.
Exam Guidelines
Exam Instructions
Question 8 of 15 :
Select the best answer for the question.
8. You've been contracted to install hardwood flooring on a basketball court. The court
measures 125' x 70'. How many square feet of flooring do you need to order for the job?
Allow 20% for waste.
k
O A. 10,500 sq. ft.
O B.234 sq. ft.
O C. 100,500 sq. ft.
O. D. 8,750 sq. ft.
Answer:
our answer is d because if you multiple 125 by 70 and subtracted from 20 you Will get D.8,750 sq. ft.
Answer:
A. 10,500 sq. ft.
Explanation:
125*70 is 8750 and 20% of 8750 is 1750 so you add it and get 10,500
what is the si unit of potential difference
Answer:
The answer is volt (V).
Explanation:
Volt is the SI unit of potential difference. The symbol of volt is V.
9. SAFELY BACKING UP YOUR VEHICLE INCLUDES ALL OF THE FOLLOWING
EXCEPT:
A. Looking over your right shoulder as you back up
O B. Checking behind your vehicle before you get in
C. Tapping your horn before you back up
Herramientas para la instalación de un picaporte
Answer:
Un picaporte es una palanca en ángulo para abrir y cerrar una puerta a mano. Por lo general, el picaporte se empuja hacia abajo para abrir la puerta. El mecanismo de la cerradura de la puerta hace que el pestillo de la cerradura se salga de la placa de la cerradura mediante la rotación del pasador. No es necesario accionar el pestillo para cerrar la puerta, ya que el pestillo encaja automáticamente en su lugar.
La conexión entre las manijas de las puertas, que generalmente están unidas a ambos lados de la hoja de la puerta, se realiza mediante un pasador cuadrado. El mandril también establece la conexión con el mecanismo de la cerradura: su escuadra es guiada a través de la escuadra interior del seguidor de la manija de la cerradura, para que gire junto con ella.
Por lo tanto, las herramientas que tienen un rol en la instalación de un picaporte son, principalmente, una agujereadora para ingresar las fijaciones, destornillador y tornillos, martillo y clavos.
write growth rate of tree ( engineering)
The low-pressure fuel system is being discussed. Technician A says that the system must provide an adequate volume of fuel to the high-pressure fuel injection system. Technician B says that the system must provide fuel at a minimum pressure to the high-pressure fuel injection system. Which technician is correct
Answer:
Hence Both technicians A and B are correct that is Technician A says that the system must provide an adequate volume of fuel to the high-pressure fuel injection system. Technician B says that the system must provide fuel at a minimum pressure to the high-pressure fuel injection system are true.
Explanation:
The low-pressure fuel system contains the fuel filters; A fuel level sending unit/tank pick-up; A transfer pump. So from considering both technicians statements both are applicable.
Explanation:
MARK ME AS A BRIANLIEST .........PLS HELP
Determine the dimensions for T if T = M V^2 A / L^3 where M is a mass, V is a velocity, A is an area, and L is a length.
L / T
No dimensions
M L / T^2
M
M / (L T^2)
Answer:
T=kg·m^2/s^2
Explanation:
T = kg (m^2/s^2) m^3 /m^3
Here I wrote down the unit for every dimension.
T=kg m^2 / s^2
m^3 is divided between m^3, this is equal to 1.
Result: T=kg·m^2/s^2
PD: I'm not sure if this is what you ask for. I hope it helps
Yall pls help me out
Determine the dimensions for T if T = M V^2 A / L^3 where M is a mass, V is a velocity, A is an area, and L is a length.
L / T
No dimensions
M L / T^2
M
M / (L T^2)
Answer:
M·L/T²
Explanation:
The given equation for T is presented as follows;
[tex]T = \dfrac{M \cdot V^2 \cdot A}{L^3}[/tex]
Where;
m = Mass with dimension M
V = Velocity, having the dimensions L/T
A = Area, having the dimensions L²
l = Length, having the dimensions, L
Therefore;
[tex]The \ dimensions \ of \ T = \dfrac{M \times (L/T)^2 \cdot L^2}{L^3} = \dfrac{M \times L^4/T^2 }{L^3} = M \cdot L/T^2[/tex]
How to programe a disk
Answer:
insert the disk in the laptop, wait of a minute or 2 and then a folder will open in my PC.
Which is one factor that scientists use to classify orders of soil?Which phrase best describes the biosphere?
Which of the following statements is correct?
Adhesive bonding allows several individual parts to be connected with nuts and bolts.
Rivets are temporary fasteners that bind two plates of metal together.
Both soldering and brazing are structurally stronger than welding.
Hardware assembly is primarily used when there is a need of being able to take individual parts out of an assembly throughout the life cycle of the product.
Answer:
b. rivets are tempory fasteners that bind two plate of metals together
locução adjetiva e de portuges ou istoria
