Explain why failure of this garden hose occurred near its end and why the tear occurred along its length. Use numerical values to explain your result. Assume the water pressure is 30 psistr

Answer:

all this could led to the failure of the garden hose and the tear along the length

Explanation:

For the flow of water to occur in any equipment, water has to flow from a high pressure to a low pressure. considering the pipe, water is flowing at a constant pressure of 30 psi inside the pipe which is assumed to be higher than the allowable operating pressure of the pipe. but the greatest change in pressure will occur at the end of the hose because at that point the water is trying to leave the hose into the atmosphere, therefore the great change in pressure along the length of the hose closest to the end of the hose will cause a tear there. also the other factors that might lead to the failure of the garden hose includes :

hoop stress ( which acts along the circumference of the pipe):

αh = [tex]\frac{PD}{2T}[/tex]     EQUATION 1

and Longitudinal stress ( acting along the length of the pipe )

αl = [tex]\frac{PD}{4T}[/tex]       EQUATION 2

where p = water pressure inside the hose

          d = diameter of hose, T = thickness of hose

we can as well attribute the failure of the hose to the material used in making the hose .

assume for a thin cylindrical pipe material used to be

[tex]\frac{D}{T}[/tex] ≥  20

insert this value into equation 1

αh = [tex]\frac{20 *30}{2}[/tex]  = 60/2 = 30 psi

the allowable hoop stress was developed by the material which could have also led to the failure of the garden hose

Discuss the ethics of the circumstances that resulted in the Columbia shuttle disaster. Considering the predictions that were made years before the disaster, as well as the reliability of the Binomial distribution and its implications, what could or should the engineers associated with the program have done differently

Consider a Carnot heat pump cycle executed in a steady-flow system in the saturated mixture region using R-134a flowing at a rate of 0.264 kg/s. The maximum absolute temperature in the cycle is 1.15 times the minimum absolute temperature, and the net power input to the cycle is 5 kW. If the refrigerant changes from saturated vapor to saturated liquid during the heat rejection process, determine the ratio of the maximum to minimum pressures in the cycle.

Suppose you have a coworker who is a high Mach in your workplace. What could you do to counter the behavior of that individual? Put the high Mach individual in charge of a project by himself, and don’t let others work with him. Set up work projects for teams, rather than working one on one with the high Mach person. Work with the high Mach individual one on one, rather than in a team setting. Explain to the high Mach individual what is expected of him and ask him to agree to your terms.

An air conditioning unit is used to provide cooling during summer for a house. If the air conditioner provides 450 kW cooling by using 150 kW electrical power, determine the coefficient of performance (COP) of the air conditioner. The outside temperature and inside temperature are 40 and 20°C, respectively. Using the inequality of Clausius determine if the cycle is possible. Determine the COP of an air conditioner working based on the Carnot cycle between the same temperature difference. Compare the COPs of the Carnot and actual air conditioners and comment on them based on your answer for the previous part (the inequality of

The amusement park ride consists of a fixed support near O, the 6-m arm OA, which rotates about the pivot at O, and the compartment, which remains horizontal by means of a mechanism at A. At a certain instant, β=30ο, 2 0.75 rad/s, and 0.5 rad/s    , all clockwise. Determine the horizontal and vertical forces (F and N) exerted by the bench on the 75-kg rider at P. Compare your results with the static values of these forces. (Use x-y coordinate system and vector equations

If the symbol is on the top and bottom of the reference line, we call this __________ sides.
A. arrow
B. other
C. both

The effective resistance of parallel resistors is always _____ than the lowest individual value.

a) more
b) less
c) no different than

Water enters the tubes of a cold plate at 70°F with an average velocity of 40 ft/min and leaves at 105°F. The diameter of the tubes is 0.25 in. Assuming 14 percent of the heat generated is dissipated from the components to the surroundings by convection and radiation and the remaining 86 percent is removed by the cooling water, determine the amount of heat generated by the electronic devices mounted on the cold plate. The properties of water at room temperature are rho = 62.1 lbm/ft3 and cp = 1.00 Btu/lbm·°F.

A large truck drives down the highway at 10 m/s hauling a rectangular trailer that is 6 m long, 2 m wide, and 2 m tall. The trailer contains frozen food and is therefore temperature-controlled. Its external surface can be approximated to be a consistent 15°C, while the outside air is at 20°C. Assume the heat transfer on the front, back, and bottom of the trailer is negligible.

a) How much cooling power must be provided to maintain the temperature controlled trailer? (i.e. What is the total heat transfer rate from the air to the trailer)?b) What is the minimum local heat transfer coefficient on the surface of the trailer? Where does the minimum occur?c) What percentage of the total heat transfer is occuring over a laminar boundary layer?d) If the cooling system can only provide 5 KW of cooling, what is the fastest speed that this truck can drive while still adequately maintaining the temperature within the trailer?

Hot oil is to be cooled by water in a 1-shell-pass and 8-tube-passes heat exchanger. The tubes are thin-walled and are made of copper with an internal diameter of 1.4 cm. The length of each tube pass in the heat exchanger is 5 m, and the overall heat transfer coefficient is 310 W/m2.K. Water flows through the tubes at a rate of 0.2 kg/s, and the oil through the shell at a rate of 0.3 kg/is. The water and the oil enter at temperatures of 20 C and 150 C, respectively. Determine the rate of heat transfer in the heat exchanger and the outlet temperatures of the water and the oil.

(20 points) (Assessment of Outcome 1): A plant has two identical standby generator units for emergency use. In the area of the generators, the normal noise level registers 82 dBA on the sound-level meter with the generators turned off. When one generator switches on, the SLM needle jumps to 85.8 dBA. What will the dBA reading be when the second generator also turns on (so that both generators are on)

A complex gear drawing done on a drawing sheet marked M-1 has many section views showing important interior details of the gear. One of the cutting-plane lines is marked at the ends with a callout in a circular bubble that says 7 above a line and M-3 below the line. To find this detail, you would

A six-lane divided multilane highway (three lanes in each direction) has a measured free-flow speed of 50 mi/h. It is on mountainous terrain with a traffic stream consisting of 7% large trucks and buses and 3% recreational vehicles. The driver population adjustment in 0.92. One direction of the highway currently operates at maximum LOS C conditions and it is known that the highway has PHF=0.90.
How many vehicles can be added to this highway before capacity is reached, assuming the proportion of vehicle types remain the same but the peak-hour factor increases to 0.95?
Process: (1) determine passenger car equivalent for trucks and buses; (2) determine passenger car equivalent for recreational vehicles; (3) calculate heavy vehicle factor; (4) determine 15-min passenger equivalent flow rate for current conditions; (5) determine 15-min passenger equivalent flow rate at full capacity; (6) calculate the volume for current and capacity conditions; (7) take the difference of the two volumes to determine how many vehicles were added

For what type of metal is high speed steel drill best suited?

Two identical 3 in. major-diameter power screws (single-threaded) with modified square threads are used to raise and lower a 50-ton sluice gate of a dam. Quality of construction and maintenance (including lubrication) are good, resulting in an estimated friction coefficient of only 0.1 for the screw. Collar friction can be neglected, as ball thrust bearings are used. Assuming that, because of gate friction, each screw must provide a lifting force of 26 tons, what power is required to drive each screw when the gate is being raised at the rate of 3 ft/min

A deep drawing operation is performed on a sheet-metal blank that is 1/8 in thick. The height of the cup = 3.8 in and its diameter = 5.0 in (both inside dimensions). (a) Assuming the punch radius = 0, compute the starting diameter of the blank to complete the operation with no material left in the flange. (b) Is the operation feasible (ignoring the fact that the punch radius is too small)?

Find a negative feedback controller with at least two tunable gains that (1) results in zero steady state error when the input is a unit step (1/s). (and show why it works); (2) Gives a settling time of 4 seconds; (3) has 10% overshoot. Use the standard 2nd order approximation. Plot the step response of the system and compare the standard approximation with the plot.

Two Electric field vectors E1 and E2 are perpendicular to each other; obtain its base
vectors.

Q10. Select the correct option for the following questions – (10 points, 2 each) a. After an edge dislocation has passed through some region of a crystal, the atomic arrangement of that region is disordered, Justify your answer - • True • False b. The process by which plastic deformation is produced by dislocation motion is called ____. • Interstitial Dislocation • Slip • Additional plain • Screw c. How does the theoretical strength of a solid material compare with its experimental strength? • Strength theoretical < Strength experimental • Strength theoretical = Strength experimental • Strength theoretical > Strength experimental d. The atoms surrounding a screw dislocation experience what kind(s) of strain(s)? • Shear strain • Compressive strain • Tensile strain e. For a particular crystal structure, the slip direction is that direction in the slip plane having the • highest linear density. • lowest linear density.

a) The current that goes through a 100 mH inductor is given as
i(t) = 6 - 2e^-2t A t >= 0
Find the voltage v(t) across the inductor.
b) The voltage v(t) = 5sin(5t) V is applied across the terminals of a 200 mH inductor. The initial current through the inductor is i(0) = -10 A. Find the current i(t) through the inductor for t > 0.

3. A storage tank is connected to a pond (at atmospheric pressure!) by a length of 4" pipe and a gate valve. From previous operating experience, it has been found that when the tank is at a pressure of 3 atm the flow through the pipe is 35 m3/h when the gate valve is fully open. If the pressure in the tank increases to 5 atm, what will be the maximum discharge rate from the tank?

Tech A says that when checking tire pressure, the tire should be " cold." Tech B says that the tires should be driven more than 3 miles before checking tire presure. Who is correct?

Determine the drag on a small circular disk of 0.02-ft diameter moving 0.01 ft/s through oil with a specific gravity of 0.89 and a viscosity 10000 times that of water. The disk is oriented normal to the upstream velocity. By what percent is the drag reduced if the disk is oriented parallel to the flow?

A refrigerator uses refrigerant-134a as the working fluid and operates on the ideal vapor-compression refrigeration cycle except for the compression process. The refrigerant enters the evaporator at 120 kPa with a quality of 34 percent and leaves the compressor at 70°C. If the compressor consumes 450 W of power, determine (a) the mass flow rate of the refrigerant, (b) the condenser pressure, and (c) the COP of the refrigerator

(USCS units) A deep drawing operation is performed on a sheet-metal blank that is 1/8 in thick. The height of the cup = 3.8 in and its diameter = 5.0 in (both inside dimensions).

(a) Assuming the punch radius = 0, compute the starting diameter of the blank to complete the operation with no material left in the flange.

(b) Is the operation feasible (ignoring the fact that the punch radius is too small)?

An R-134a refrigeration system is operating with an evaporator pressure of 200 kPa. The refrigerant is 10% in vapor phase at the inlet of the evaporator. The enthalpy and temperature of the refrigerant at the exit of the compressor are 360 kJ/kg and 70 /C respectively. If this system (with the refrigerant flowing at 0.005 kg/s) is used to cool a 750 kg product (initial temperature = 80 /C and specific heat = 3,000 J/kg-K), what will be the temperature of the product after 6 hours?

A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by eight struts to an insulated outer tube of 60-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k 50 W/m K). Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m2 K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water?

A machine operates using air flow under steady conditions with the following inlet and exit flow parameters. At the inlet, the pressure is 1.75 MPa at a temperature of 300 K. The inlet velocity is 25 m/s. The inlet diameter is 20 cm. At the outlet, the pressure is decreased to 55 kPa at a temperature of 500 K. The outlet velocity is 100 m/s. The elevation increase between the inlet and outlet is 100 m. The machine includes a turbine operating at 5 kW

Determine mass flow rate through the machine.

The supplement file* that enclosed to this homework consists Time Versus Force data. The first column in the file stands for time (second) and the 2nd stands for force (Volt), respectively. This data were retrieved during an impact event. In this test, an impactor strikes to a sample. A force-ring sensor that attached to the impactor generates voltage during collision. A data acquisition card gathers the generated signals.

Have you ever had an ice cream headache that’s when a painful sensation resonates in your head after eating something cold usually ice cream on a hot day this pain is produced by the dilation of a nerve center in the roof of your mouth the nerve center is overreacting to the cold by trying to hit your brain ice cream headaches have turned many smiles to frowns identify the structure