With a serverless application, you can deploy a simple application or one that is easily divided into several smaller microservices. Alternatively, a bigger, trickier application.
What feature do containers and serverless have in common?Both are cloud-based, and serverless computing significantly reduces infrastructure overhead compared to containers. Applications are divided into smaller components and delivered in both types of architecture. Each container in a container-based architecture will execute a single microservice.
What does the forensic term "artefacts" mean?Forensic artefacts, The forensic items with some forensic value are called forensic artefacts. Any item that records information or provides proof of an event, such as logs, registers, hives, and many more.
To know more about application visit:-
https://brainly.com/question/28650148
#SPJ1
True or False? Fourth-degree burns can be caused by too much sun or brief contact with hot objects, hot water, or steam.
Note that it is FALSE to state that Fourth-degree burns can be caused by too much sun or brief contact with hot objects, hot water, or steam.
What is the rationale for the above response?There is no such thing as "fourth-degree" burns. Burns are usually classified into three categories: first-degree, second-degree, and third-degree burns.
First-degree burns affect the outer layer of skin, while second-degree burns affect both the outer layer and underlying layer. Third-degree burns are the most severe and involve damage to all layers of the skin and potentially deeper tissues.
Burns can be caused by exposure to flames, hot liquids, chemicals, or electricity, but excessive sun exposure does not typically result in third-degree burns.
Learn more about burns:
https://brainly.com/question/29538270
#SPJ1
Dante uses ______ DSCP tags for QoS.
Dante employs layer 3 QoS tagging called DSCP (Diffserv).
What does DSCP mean?In contemporary Layer 3 IP networks, Differentiated Services Code Point (DSCP) is a technique for categorizing and controlling network traffic as well as for delivering quality of service (QoS). Differentiated services, also known as DiffServ, is an IP-based computer networking architecture that defines a method for categorizing, controlling, and delivering quality of service to network traffic on contemporary IP networks. DSCP Score. Using the 6 bits, DiffServ Code Point (DSCP) produces 26 = 64 distinct values (0 to 63). describes the values of the DSCP standards. The remaining DSCP values can be altered to meet the QoS specifications.
How does DSCP QoS work?Network data traffic classification is determined by Quality of Service (QoS) DSCP Marking. This can be used to identify the network traffic that uses more bandwidth, is more important, and has a higher chance of dropping packets.
To know more about DSCP visit:
https://brainly.com/question/29590727
#SPJ1
_____ are used in standardized tests, including the SAT and GMAT tests, and to record votes in elections.
a. Optical character recognition (OCR) systems
b. Speech recognition devices
c. Optical mark recognition (OMR) systems
d. Magnetic Ink Character Recognition (MICR) devices
Answer:
О c. OMR Optical Mark recognition.
Explanation:
OMR are used in standarized tests, including the SAT and GMAT tests, and to record votes in elections.
...
Can you think of a product that you love even though it may not work perfectly? Why do you love it?
Yes, I can think of a product that I love even though it may not work perfectly.
That product is my old laptop. Even though it may not be as fast as the newer models and it may have some technical difficulties, I still love it because it holds a lot of memories for me. It is the first laptop I ever owned and I used it throughout my college years. It is also the laptop that I used to start my first business and it helped me to achieve a lot of success.
So, even though it may not work perfectly, I still love it because of the sentimental value it holds for me.
Learn more about old laptop:
https://brainly.com/question/13843607
#SPJ11
Yes, I can think of a product that I love even though it may not work perfectly.
That product is my old laptop. Even though it may not be as fast as the newer models and it may have some technical difficulties, I still love it because it holds a lot of memories for me. It is the first laptop I ever owned and I used it throughout my college years. It is also the laptop that I used to start my first business and it helped me to achieve a lot of success.
So, even though it may not work perfectly, I still love it because of the sentimental value it holds for me.
Learn more about old laptop:
brainly.com/question/13843607
#SPJ11
Determine the length of welds required to transmit a load 54.5 KN between 12.7mm. thick plates, when the plates are to be joined by 1) Two parallel fillet welds. 2) Two transverse fillet welds.
For the parallel fillet weld, the length required is 24.52mm and for transverse fillet welds, the longer fillet weld required is 24.39 mm and the length of the shorter fillet weld required is 6.13 mm.
What is the length to transmit the loadThe length of weld required to transmit a load between two plates depends on the type of weld used and the strength of the material being welded. For the given scenario:
Two parallel fillet welds:
The length of each fillet weld required can be calculated using the following formula:
L = (2 x F x P) / (0.7 x T)
where L is the length of each fillet weld, F is the applied force (54.5 KN), P is the perimeter of the weld (2 x length of the joint), T is the thickness of the plate (12.7 mm), and 0.7 is a constant. Substituting the values, we get:
L = (2 x 54.5 x 2) / (0.7 x 12.7) = 24.52 mm
Therefore, the length of each fillet weld required is 24.52 mm.
Two transverse fillet welds:
The length of each fillet weld required in this case can be calculated using the same formula as above, but with the perimeter of the weld being the sum of the lengths of the two sides being welded. Since the two fillet welds are transverse, their lengths will be different. Assuming one fillet weld is longer than the other, we can calculate their lengths as follows:
L1 = (F x P1) / (0.7 x T)
L2 = (F x P2) / (0.7 x T)
where L1 and L2 are the lengths of the two fillet welds, P1 and P2 are the perimeters of the two sides being welded, and all other variables are the same as before. We can assume that the longer fillet weld is on the side with the higher applied force, so we have:
P1 = 2 x length of joint
P2 = length of joint
Substituting the values, we get:
L1 = (54.5 x 2 x 2) / (0.7 x 12.7) = 24.39 mm
L2 = (54.5 x 1) / (0.7 x 12.7) = 6.13 mm
Therefore, the length of the longer fillet weld required is 24.39 mm and the length of the shorter fillet weld required is 6.13 mm.
Learn more on applied force here;
https://brainly.com/question/25732012
#SPJ1
Submittal of bonds and insurance certificates should be submitted by the bidder to whom the contract has been awarded: A. at the time of submitting the original Bid. B. after receiving the Notice to Proceed from the owner/engineer. C. after receiving the Notice to Proceed, but before signing the Agreement. D. after receiving Notice of Award, but before owner signs the Agreement.
A buyer may meet with several potential suppliers to negotiate a potential acquisition at a bidding conference.
Certificate signing request is referred to as CSR. Request for certification is another name for it. When a candidate applies for a digital identity certificate, a message is sent to the security certificate authority. The applicant's public key is included in the certificate signing request. It includes the essential details, such as the domain name and digital signature. So, in order to obtain a fresh certificate, the administrator needs submit the CSR, or certificate signing request. The initial hearing is a less formal gathering where questions about the charges are put to the accused before a trial. Both sides might negotiate during the hearing in an effort to avoid holding a trial. The certification holders would automatically go to trial if they don't request a hearing first.
Learn more about CSR here:
https://brainly.com/question/13681474
#SPJ4
Fill in the blank: In ggplot2, you use the _____ to add layers to your plot.a. Apipe operator (%>%)
b. Bequal sign (=)
d. Campersand symbol (&)
e. Dplus sign (+)
The term "mapping" in ggplot2 describes the relationship between variables and a charting object, such as a point, line, or other shape.
A charting object, such as a point, line, or other shape, is what the gg plot2 system refers to as a geom. Bar charts, scatterplots, and line diagrams are just a few of the many layouts, shapes, or forms that ggplot2 can take. For instance, the representations of various Geom types include geom bar(), geom point(), geom line(), etc. The term "mapping" in ggplot2 refers to the relationship between variables, and a "Geom" is used to create various ggplot2 layouts, shapes, or forms, such as bar charts, scatterplots, and line diagrams. So, the term "mapping" in ggplot2 refers to the relationship between variables and a charting object such as a point, line, or other shape.
Learn more about gg plot2 here:
https://brainly.com/question/29496067
#SPJ4
Design a helical spring for an engine valve length of the spring when the valve in open in 45mm. and the length when closed in 55mm. spring load on the valve when open is 450N and when closed in 300N. Minimum internal diameter of the spring is 30mm. Take permissible shear stress = 400 N/mm2, and G = 0.8 x 105 N/mm2.
Hi dude how r u...........
Graph G is defined by the arrow diagram below. Select the pair of vertices such that there is no walk of length 4 in G from the first vertex to the second vertex. 4 0 4,3 O 2,1 0 1,3 O 1,4
A parabola is an equation of a curve with a point on it that is equally separated from a fixed point and a fixed line.
The equation represents a parabola with a vertex at (1,3) and an opening downward. A parabola is a mirror-symmetrical, roughly U-shaped planar curve in mathematics. Many seemingly unrelated mathematical descriptions that all correlate to the same curves can be used to define it. A parabola can be represented by a point and a line. The provided equation is 3x2 - 6x + 4y - 9 = 0. Plotting the graph of the given equation reveals that the parabola that results is opened downward and has a vertex at the point ( 1,3). Attached are the graph and the answer that follows. Option C is the right answer since it represents a parabola with a vertex at (1,3) opening downward.
Learn more about A parabola here:
https://brainly.com/question/21083314
#SPJ4
A boy riding a bicycle can be modeled as a spring-mass-damper system with an equivalent weight, stiffness, and damping constant of 800 N, 50,000 N/m, and 1,000 N-s/m, respectively. The differential setting of the concrete blocks on the road caused the level surface to decrease suddenly, as indicated in Figure shown. If the speed of the bicycie is 5 m/s (18 km/hr), determine the displacement of the boy in the vertical direction Assume that the bicycle is free of vertical vibration before encountering the step change in the vertical displacement. Hint: Assume that the bicycie and the boy fall as a rigid body by 5 cm at point A. Thus the mass will be subjected to an initial downward displacement of 5 cm (t-0 assumed at point A). ed keq cm
The youngster has moved about 0.065 meters in the vertical direction (6.5 cm).
What was the purpose of the query?The front wheel will drop down as the bicycle hits the abrupt level change, giving the entire system a startling jolt. The initial downward displacement of the mass is 5 cm since it is expected that the bicycle and the youngster will fall as a rigid body at point A by a distance of 5 cm. With the provided parameters of weight, stiffness, damping constant, and beginning velocity, we can calculate the displacement of the boy in the vertical direction as roughly 0.065 m (6.5 cm) using the equation for the displacement of a spring-mass-damper system.
To know more about system consisting of a spring visit:
https://brainly.com/question/29613751
#SPJ1
3. The _______on an electric motor provides information that will assist a
person in selecting, installing, and energizing the correct motor for the job.
Note that the nameplate or rating plate on an electric motor provides information that will assist a person in selecting, installing, and energizing the correct motor for the job.
Who invented the Electric Motor?The electric motor was not invented by a single individual, but rather its development involved the work of many scientists and inventors over time.
The earliest form of an electric motor was created in 1821 by Michael Faraday, who demonstrated the conversion of electrical energy into mechanical motion. Subsequent inventors such as Thomas Davenport, Nikola Tesla, and Galileo Ferraris made significant contributions to the development of the electric motor, paving the way for its modern-day applications in a wide range of industries.
Learn more about nameplate:
https://brainly.com/question/1414905
#SPJ1
During peak systole, the heart delivers to the aorta a blood flow that has a velocity of 90 cm/sec and a pressure of 120 mmHg. The aortic root diameter is 27mm. Determine the force (in Newtons) acting on the aortic arch if the conditions at the outlet
are a pressure of 115 mmHg and d2 = 22mm. (Neglect body forces, assume uniform and
steady flow)
V1 = 90 cm/s
P1g = 120 mmHg
P2g = 115 mmHg
Density blood = 1.057 g/cm3
The force acting on the aortic arch is -1907.26 N as per the given data.
What is Bernoulli's equation?The relationship between pressure, kinetic energy, and gravitational potential energy of a fluid in a container is known as Bernoulli's equation.
To determine the force acting on the aortic arch, we need to convert the units of velocity, pressure, and diameter to SI units (m/s, Pa, and m respectively).
Then, we can use the principle of continuity of flow and the equation of energy conservation (Bernoulli's equation) to calculate the force.
First, we'll convert the velocity, pressure, and diameter:
V1 = 90 cm/s = 0.9 m/s
P1g = 120 mmHg = 120 x 133.322 Pa = 16039.64 Pa
P2g = 115 mmHg = 115 x 133.322 Pa = 15345.83 Pa
d1 = 27 mm = 0.027 m
d2 = 22 mm = 0.022 m
Next, we'll use the principle of continuity of flow to calculate the velocity at the outlet (V2) and cross-sectional area (A2):
A1 x V1 = A2 x V2
[tex]V2 = V1 X (A1 / A2) = 0.9 x (\pi X (0.027^2) / 4) / (\pi X (0.022^2) / 4) = 1.33 m/s[/tex]
Finally, we'll use Bernoulli's equation to calculate the pressure at the outlet (P2) and then calculate the force acting on the aortic arch:
[tex]P1g + (1/2) X \rho X V_1^2 = P2g + (1/2) \rho X V_2^2[/tex]
[tex]P2 = P1g + (1/2) X \rho X V_1^2 - (1/2) X \rho X V_2^2 = 16039.64 + (1/2) X 1.057 X 0.9^2 - (1/2) X 1.057 X 1.33^2 = 14159.56 Pa[/tex]
[tex]F = (P_2 - P_1g) X A1 = (14159.56 - 16039.64) X \pi X (0.027^2) / 4 = -1907.26 N[/tex]
Thus, the force acting on the aortic arch is -1907.26 N. The negative sign indicates that the force is acting in the opposite direction to the flow, which is normal in fluid mechanics.
For more details regarding Bernoulli's equation, visit:
https://brainly.com/question/30504672
#SPJ9
Identify a Hypertext Markup Language (HTML) embedded element that contains programming scripts used to construct bitmap images and graphics.a. Canvas
b. Iframe
c. Object
d. Embed
JavaScript drawings can now be created programmatically using HTML5 canvas, which is used in conjunction with the canvas> tag.
The term "head element" refers to a container used to store hidden metadata. The element must be positioned between the html tag and the body tag. A document's metadata, or machine-readable information, include the document's title, author, page description, style sheets, keywords, scripts, and other information. As a result, the information stored in the head element is mostly data that can be processed by a machine rather than data that can be read by a human. This metadata has the benefit of not being seen on the page. The machine will be able to recognize and read it, though. HTML requires a head element, which should only be used once.
Learn more about Head element here:
https://brainly.com/question/4276446
#SPJ4
Establishing stability within your object is critical to your ability to ________
Learned helplessness is the idea that we have no influence over how something will turn out, whether it is true or not.
Because some food ingredients, such as oxalic acid and phytic acid, which naturally present in some plants, can bind with calcium and impede its absorption in the body, the body's capacity to absorb calcium will diminish if we consume a diet high in calcium. Spinach, collard greens, beans, and sweet potatoes all have significant oxalic acid content. Whole grain products that contain fibre, seeds, and soy isolates are examples of foods that contain phytic acid. Just 30% of the calcium in food is absorbed by humans, and this varies depending on the sort of food we are eating. Individuals who behave in this way typically have gone through a number of adverse circumstances that were beyond of their control. They most likely won't make an effort to avoid unpleasant stimuli in the future because of this.
Learn more about Calcium here:
https://brainly.com/question/15244115
#SPJ4
A battery charge controller incorporates an MPPT to optimize charging of the batteries. Assume the maximum power voltage of a PV array to be 99 V and the bulk charge voltage level of a 48 V vented lead-acid battery bank to be 56 V.If the conversion efficiency of the MPPT is 98%, estimate the percentage increase in charge delivered to the battery under these conditions over that which would be delivered by a controller that causes the array to operate at 56 V rather than 96 V. You may assume the PV array consists of three modules connected in series, that Vmp is independent of irradiance levels, and each module has Voc 42 V, ISc 6.25 A, Vimp 33 V, and Imp 5.76 A.
A source of constant voltage is referred to as a DC voltage, and a source of periodic, time-varying voltage is referred to as an AC voltage.
The average voltage is equal to (9 + 6)/2 (15/2) = 7.5. 20 mA Equals 20 x current 80 hours is equal to 80 x 60 x 60, or 288000 seconds. In the event that the current is considered to be constant, the energy supplied is calculated as the product of the voltage across, the current delivered, and the duration of the delivery. Energy provided by the battery is equal to 7.5 × 20 x 288000 = 43200 J. 43.2 kJ of energy. It follows that there is no potential difference between them at 6-v if the battery is deemed dead when it reaches that voltage. The capacity of a flashlight battery is calculated as the sum of the supplied current and the delivery time. capacity is equal to 20 mA x 80 hr, or 1600 mAh.
Learn more about Voltage here:
https://brainly.com/question/16860502
#SPJ4
The ambient temperature is 70° and the humidity is low. With the AC on, what should the high-side gauge pressure be?
The high-side gauge pressure can not be calculated as information given here is not sufficient. The correct option is C.
What is high-side gauge pressure?The pressure of the refrigerant on the high side of the air conditioning system, which is the side of the system following the evaporator, is measured by the high-side gauge pressure.
The type of refrigerant used, the size and architecture of the AC system, as well as the surrounding temperature and humidity, all have an impact on the high-side gauge pressure in an air conditioning system.
Low humidity is typically regarded as advantageous for air conditioning systems since it lowers the quantity of moisture in the air, which can facilitate the system's ability to chill the air.
However, it is impossible to precisely calculate what the high-side gauge pressure should be under these circumstances without knowing more details about the particular AC system.
It is preferable to seek advice from a licensed HVAC expert or review the system's manufacturer's specs.
Thus, the correct option is C.
For more details regarding high-side gauge pressure, visit:
https://brainly.com/question/30382001
#SPJ9
Your question seems incomplete, the complete question is attached below:
according to science define charge
Which activity is key to successfully implementing the Scaled Agile Framework?
The key activity to successfully implementing the Scaled Agile Framework (SAFe) is alignment.
Alignment is the process of ensuring that all teams and individuals are working towards the same goals and objectives. This is important because it ensures that everyone is on the same page and that the work being done is in support of the overall goals and objectives of the organization.
By aligning all teams and individuals, the organization can more effectively implement SAFe and achieve the desired results.
Learn more about the Scaled Agile Framework:
https://brainly.com/question/29848651
#SPJ11
The key activity to successfully implementing the Scaled Agile Framework (SAFe) is alignment.
The Alignment ProcessAlignment is the process of ensuring that all teams and individuals are working towards the same goals and objectives. This is important because it ensures that everyone is on the same page and that the work being done is in support of the overall goals and objectives of the organization.
By aligning all teams and individuals, the organization can more effectively implement SAFe and achieve the desired results.
Learn more about the Scaled Agile Framework:
brainly.com/question/29848651
#SPJ11
A sample contains 10. 5 g of the radioisotope pb-212 and 157. 5 g of its daughter isotope, bi-212. How many half-lives have passed since the sample originally formed?.
Four half-lives after the sample's creation, the sample must have passed. This kind of radioactive decay is common, and all radioactive processes adhere to first order kinetics.
What is an isotope's longest half-life?The half-life of xenon-124, or the typical amount of time needed for a collection of xenon-124 atoms to decay by half, is about 18 sextillion years (1.8 x 1022 years), or roughly 1 trillion times the universe's present age.
How long is a radioactive isotope's half-life?Half-life is a unit used to describe the rate of radioactive isotope decay. A radioactive material's half-life is the amount of time it takes for half of its atoms to break apart.
To know more about half-lives visit :-
https://brainly.com/question/1439925
#SPJ4
when following another vehicle use low beam whenever you are within (True or False)
True, It is illegal to have your high beams on when passing by another car and the reason for that is because they're bright duh lol, and it may be a risk to blind the drivers eyeballs off.
Hope I helped sire
Answer: it true Dear <3
Explanation: I hope this helps^^
A plantwide overhead rate based on direct labor hours is ______ appropriate. a. always
b. sometimes
c. frequently
d. never
A plantwide overhead rate based on direct labor hours is sometimes appropriate. Hence, option B is correct answer.
The use of plantwide overhead rate based on direct labor hours is a traditional and simplistic approach to allocate overhead costs to the products. This approach has some advantages such as simplicity, low cost, and easy to understand. However, it also has some limitations that make it an inappropriate method to allocate overhead costs in some situations.
One of the limitations of the plantwide overhead rate based on direct labor hours is that it assumes that overhead costs are driven by labor hours. This assumption may not be accurate in some situations where the overhead costs are driven by factors other than direct labor hours such as machine hours, material usage, or number of setups. In such cases, using a plantwide overhead rate based on direct labor hours will result in distorted product costs, leading to incorrect pricing and profitability analysis.
Another limitation of the plantwide overhead rate is that it treats all products as if they consume the same amount of overhead resources. However, some products may consume more overhead resources than others due to their complexity, customization, or special handling requirements. As a result, using a plantwide overhead rate will result in under costing of complex or customized products and overcosting of simple or standard products.
In conclusion, a plantwide overhead rate based on direct labor hours is sometimes appropriate, but it should be used with caution and only in situations where the overhead costs are primarily driven by direct labor hours, and the products consume overhead resources in a similar manner. In situations where the overhead costs are driven by other factors, or the products consume overhead resources differently, alternative methods such as activity-based costing should be used to allocate overhead costs accurately.
To know more about traditional: https://brainly.com/question/9450983
#SPJ4
After improving their machine guarding program, a company's medical costs were reduced by over $60,000 in one
year. What type of benefit was this medical cost reduction?
A. Indirect benefit
B. Direct benefi
C. Both indirect and direct benefit
D. Neither indirect or direct benefit
Answer:
I believe the answer is D. Neither indirect or direct benefit
Explanation:
if I'm wrong then its B. Direct benefit
a stamped plate evaporator usually does not use a fan to move air across it. true false
The statement "a stamped plate evaporator does not typically use a fan to move air through it" is false.
A stamped plate evaporator, also known as a fin evaporator, typically uses a fan to move air through it. The fan helps increase the efficiency of the evaporator by increasing the amount of air that comes in contact with the evaporator surface. This helps transfer heat more effectively and cool the "air" more efficiently. Without a fan, the evaporator would not be as effective at cooling the air. Therefore, the statement is false.
Learn More About evaporator
https://brainly.com/question/28265210
#SPJ11
if humidity sensors are not used to control humidity, ? can control humidity by taking advantage of the relationships between temperature and humidity.
Temperature sensors can use the relationships between temperature and humidity to control humidity if humidity sensors are not utilized.
What benefits do temperature and humidity sensors provide?These instruments are used to measure the actual humidity of the air at any given location or point. When air conditions need to be controlled for a variety of reasons or when they may be extreme, such devices are frequently used.
Why is it crucial to keep an eye on the relative humidity?Controlling moisture around a finished product is by far and away the most important reason to monitor relative humidity. This typically entails ensuring that the RH does not rise too high.
To know more about Temperature sensor visit :-
https://brainly.com/question/14258631
#SPJ4
Cameras transfer aspects of space to viewers. What is this process called?
Mediation is the method of conveying elements of space to viewers using cameras. Information transmission from one source to another is referred to as mediation.
What methods do filmmakers employ to distort space and time?Cross-cutting, commonly referred to as parallel editing, is a method used throughout the editing process. It is used to change both time and space. It is therefore simultaneous action taking place in various locations. These areas are typically close together.
Cinematography refers to either the process of recording moving pictures on film or a digital storage medium.The art of cinematography involves recording moving pictures on film or a digital storage medium. The name is derived from three Greek roots: kinesis, which means "movement," photo, which means "light," and graphic, which means "writing," but it was not used until motion pictures were created.
to know more about Cameras here;
brainly.com/question/10944268
#SPJ1
2.8 For Fig.
2−30
a-d, find all equivalent resistances (Req): (a) (b) (c) Fig. 2-30 (d) (e) 2.9 For Fig. 2-31 a-d, find all equivalent resistances (Req): Fig. 2-31 (a) (c) (d)
2.10
Attach a
10 V
load to the terminals and find the voltage and current across each resistor in the above circuits of Fig.
2−31
. This work is licensed under a Creative Commons Attribution
4.0
International License.
The right response is to Consider Figure 1, which shows the electric field lines of a solitary positive point charge. An electric field line that is produced by a positive charge.
Radiation from RF (radio frequency) waves is produced by all computers. There is no proof that they are harmful unless the intensity is high enough to warm tissue (like a microwave oven). You are not putting yourself in danger if you use your computer for more than four hours each day (from radiation). Computers emit electromagnetic radiation into the environment. In particular, electromagnetic radiation that is visible light is produced. It is also possible for computers to produce other forms of electromagnetic radiation, such as radio waves, ultraviolet light, and infrared light, depending on the components of the device. Avoid using them an hour before going to bed. Even though it may be in your bedroom, you are under no obligation to use it.
Learn more about Electromagnetic radiation here:
https://brainly.com/question/30694959
#SPJ4
Find the surface area of a square pyramid with a base length of 24cm and a height of 16cm.
The area of a square pyramid with a height of 16 cm and a base length of 24 cm is 1536 cm2.
What does the square pyramid's surface area represent?A square pyramid's surface area is the sum of the square's base area and the areas of its four triangular side faces. The square pyramid's surface area is equal to a2+2al (or) a2+2a a24+h2 a 2 4 + h 2 if a, h, and l are the base length, pyramid height, and slant height, respectively.
How is the pyramid's formula found?The formula V = (1/3) Bh, where B is the base area and h is the height of the pyramid, can be used to calculate the volume of a pyramid. Since any polygon can serve as a pyramid's base, we can use formulas for the area of polygons to locate "B."
To know more about base length visit :-
https://brainly.com/question/12180117
#SPJ4
For a given soil, the following are known: Gs = 2. 74, moist unit weight, y = 20. 5 kN/m³, and moisture content, w = 16. 6%. Determine:
a. Dry unit weight
b. Void ratio
c. Porosity
d. Degree of saturation
In a Dry Unit, The soil has a weight of 17.5 kN/m3, a void ratio of 0.347, a porosity of 0.384, and a saturation level of 86.7%.
Dry Unit; The formula d = w(1-w), where d is the dry unit weight, w is the wet unit weight, and w is the moisture content, can be used to determine the weight of the soil. In this instance, d = w. (1-w) nγd = 19.6(1-0.143) = 17.5 kN/m3. Using the formula e = (w / (1-w)), where e denotes the void ratio and w denotes the moisture content, the Void Ratio is then determined. Using the values from above as plug-ins, e = (w / (1-w)), e = 0.143/(1-0.143) = 0.347. Therefore, using the formula n = e/[1 + (G•e)], where n is the porosity, e is the void ratio, and G is the specific gravity, the porosity is computed. In this instance,n = e/[1 + (G•e)],n = 0.347/[1 + (2.75•0.347)] = 0.384.
Learn more about Dry unit weight here:
https://brainly.com/question/30158521
#SPJ4
In the case below, the original source material is given along with a sample of student work. Determine whether the student is guilty of plagiarism.Original Source Material:There is a design methodology called rapid prototyping, which has been used successfully in software engineering. Given similarities between software design and instructional design, we argue that rapid prototyping is a viable method for instructional design, especially for computer-based instruction. References:Tripp, S. D., & Bichelmeyer, B. A. (1990). Rapid prototyping: An alternative instructional design strategy. Educational Technology Research and Development, 38(1), 31-44. Student Version:Rapid prototyping could be an advantageous methodology for developing innovative computer-based instruction (Tripp & Bichelmeyer, 1990). References:Tripp, S. D., & Bichelmeyer, B. A. (1990). Rapid prototyping: An alternative instructional design strategy. Educational Technology Research and Development, 38(1), 31-44. Which of the following is true for the Student Version above?
The act of presenting someone else's words or ideas as your own is known as plagiarism. By paraphrasing, you can put another person's ideas into your own words.
Is plagiarism possible when paraphrasing?Paraphrasing without crediting the original author is plagiarism because you are presenting someone else's ideas as if they were your own. However, paraphrasing is not plagiarism if the source is properly cited.
Is it illegal to copy someone else's work by paraphrasing?You might want to rephrase or paraphrase a book's paragraph or section for your paper if you like its content. Even though it is not against the law, paraphrasing must be cited inacademic papers as a professional courtesy.
To know more about paraphrasing visit :-
https://brainly.com/question/29890160
#SPJ4
Which of the following characteristics of an object-oriented programming language restricts behavior so that an object can only perform actions that are defined for its class?
Polymorphism
Inheritance
Encapsulation
Programmers who use object-oriented methods consider in terms of a class instance that has its own properties and behaviours, which is how they vary from those who use procedural methods.
Procedural programming tackles applications by managing difficulties using a top-down method where it solves problems from the top of the code and to the bottom, whereas object-oriented programming is known to be one that employs classes and objects. A programming design strategy known as procedural programming attempts to break down clearly specified tasks into modules, functions, etc. In object-oriented programming, objects are only the individual parts of a programme. The (c) Method defines the behaviour of objects. The behaviour of objects is defined through methods, which are merely functions and subroutines. Consider the following approach, for instance: Public static int (int I Fibonacci
Learn more about Procedural programming here:
https://brainly.com/question/26709198
#SPJ4