Objective of the assignment The main objective of this assignment is to perform a study of demonstrate a simulation of three-phase transformer.
The following are the tasks involved in the simulation: 1. Demonstrate the simulations of the simplified per phase equivalent circuit of a three-phase transformer referred to the primary side. 2. Demonstrate the simulations of the simplified per phase equivalent circuit of a three-phase transformer referred to the secondary side. 3. Students may define their own setting of parameter for both simulations mode. 4. Compare simulation results in (1) and (2) with the value obtained through manual calculation. 5. Relate your simulation model with possible losses in the transformer and suggest the ways to overcome these losses. 6. Provide and discuss two (2) applications of transformer in the power transmission system. 7. Justify the environmental effect of the three-phase transformer in the power transmission system.
Environmental effect of the three-phase transformer in the power transmission system The environmental effects of the three-phase transformer in the power transmission system are justified as follows:The noise generated by transformers in urban areas is regarded as a form of environmental pollution. Transformer oil that is contaminated can harm the environment and people's health. If there is a transformer failure, it can lead to environmental pollution. Transformers are a source of electromagnetic fields (EMFs) that may affect people's health.
To know more about assignment visit:
brainly.com/question/33223512
#SPJ11
Assume you have written a program that calculates and displays the values of (x,y) coordinate pairs at each time interval for a projectile. As the output from your program, you want to display the values for time, x, and y beneath the following headings Time x-coordinate y-coordinate (in seconds) Thorizontal displacement) (vertical displacement) You decide to avoid "cluttering up the main function by defining a separate user-defined function to handle only the column heading display shown above. This other function will then be called by main. This other function will not return anything. Which of the following would be an appropriate heading for this function? a int printHeadings (int x, inty) Ob vold peintheadings string printHeadings) a.char print Headings (char x, chary e. None of the above
If the output from your program is to display the values for time, x, and y beneath the following headings: Time, x-coordinate, and y-coordinate.
Then, to avoid cluttering up the main function by defining a separate user-defined function to handle only the column heading display shown above, an appropriate heading for this function will be `void printHeadings()`.This other function will then be called by main.
This other function will not return anything, meaning it will not have any return statement. It will only perform a print operation on the console window or terminal to display the heading information for each column. Therefore, the function should be defined as a void function.
To know more about output visit:
https://brainly.com/question/14227929
#SPJ11
The file Animals.txt found in the input folder contains a long list of animal names, one per line. Create an application that reads that file and creates a collection of animal names. Use the ArrayCollection class. Your application should then generate a random character and challenge the user to repeatedly enter an animal name that begins with that character, reading the names entered by the user until they either enter a name that does not begin with the required character or is not in the collection, or they enter a name they used before. Finally, your application reports how many names they successfully entered.
The application code has been written below
How to write the codeimport java.io.File;
import java.io.FileNotFoundException;
import java.util.*;
public class AnimalGame {
private static final String FILE_PATH = "input/Animals.txt";
public static void main(String[] args) {
// Read animal names from file and create the collection
ArrayCollection<String> animalCollection = readAnimalNamesFromFile(FILE_PATH);
// Generate a random character
char randomChar = generateRandomCharacter();
// Play the animal name game
playAnimalNameGame(animalCollection, randomChar);
}
private static ArrayCollection<String> readAnimalNamesFromFile(String filePath) {
ArrayCollection<String> animalCollection = new ArrayCollection<>();
try {
File file = new File(filePath);
Scanner scanner = new Scanner(file);
while (scanner.hasNextLine()) {
String animalName = scanner.nextLine().trim();
animalCollection.add(animalName);
}
scanner.close();
} catch (FileNotFoundException e) {
System.out.println("File not found: " + filePath);
}
return animalCollection;
}
private static char generateRandomCharacter() {
Random random = new Random();
return (char) (random.nextInt(26) + 'a');
}
private static void playAnimalNameGame(ArrayCollection<String> animalCollection, char randomChar) {
Scanner scanner = new Scanner(System.in);
HashSet<String> enteredNames = new HashSet<>();
int successfulAttempts = 0;
System.out.println("Welcome to the Animal Name Game!");
System.out.println("Enter an animal name that begins with the character: " + randomChar);
System.out.println("Enter 'exit' to quit the game.");
while (true) {
System.out.print("Enter an animal name: ");
String animalName = scanner.nextLine().trim().toLowerCase();
if (animalName.equals("exit")) {
break;
}
if (!animalName.startsWith(String.valueOf(randomChar))) {
System.out.println("The name should start with the character: " + randomChar);
continue;
}
if (!animalCollection.contains(animalName)) {
System.out.println("The entered name is not in the collection.");
continue;
}
if (enteredNames.contains(animalName)) {
System.out.println("You've already entered that name before.");
break;
}
enteredNames.add(animalName);
successfulAttempts++;
}
System.out.println("You entered " + successfulAttempts + " valid animal names.");
}
}
Read more on application codes here https://brainly.com/question/26789430
#SPJ4
The purpose of PAV test is to: a) simulate short-term aging of asphalt concrete manufacture b) Simulate oxidative aging during service c) Determine temperature below which there's no fire hazard d) Correlate fatigue damage and rutting 10. Which one is NOT the advantage of asphalt emulsion over cutback? a) It cures faster b) It is cost effective. c) It does not release hazardous materials. d) It uses water to make emulsion 11. What distress mode will most likely happen if hard grade asphalt is used in a cold arca? a) Rutting b) Fatigue cracking c) Thermal cracking d) None of them 12. On the viscosity of asphalt binder, which statement is NOT correct? a) Viscosity of asphalt decreases when temperature increases. b) Viscosity of asphalt decreases after aging. c) Viscosity of asphalt increases after hot mixing and placing. d) Viscosity of asphalt increases after volatilization of hydrocarbons. 13. Which one is NOT the reason to compact asphalt concrete? a) To prevent further compaction b) To provide shear strength or resistance to rutting e) To ensure the mixture is waterproof d) To ensure excessive oxidation of the asphalt binder. 14. What is NOT the advantages of warm mixed asphalt? a) Energy savings b) Decreased emissions c) Decreased fumes d) Increased binder ageing 15. To simulate the aging of asphalt binder after 5-year service, which test should be conducted? a) RTFO b) PAV c) Flash point d) Rotational viscometer.
The RTFO test subjects the asphalt binder to elevated temperature and airflow, simulating the oxidative aging that occurs over time during service conditions. This test helps evaluate the long-term aging characteristics of the binder.
10. The purpose of the PAV (Pressure Aging Vessel) test is to **simulate short-term aging of asphalt concrete manufacture**. This test is conducted to assess the performance of asphalt binders under accelerated aging conditions, replicating the effects of oxidative aging that occur during the manufacturing process.
11. The distress mode that is most likely to happen if hard grade asphalt is used in a cold area is **thermal cracking**. Hard grade asphalt is less flexible and more susceptible to thermal stress, which can lead to cracking when exposed to cold temperatures.
12. The statement that is **not correct** regarding the viscosity of asphalt binder is: **Viscosity of asphalt decreases after hot mixing and placing**. In fact, the viscosity of asphalt increases after hot mixing and placing due to cooling and solidification of the binder.
13. The reason to compact asphalt concrete does not include: **To ensure excessive oxidation of the asphalt binder**. Compaction of asphalt concrete is performed to achieve a denser and more tightly packed pavement structure, providing benefits such as improved load-bearing capacity, increased resistance to rutting, and enhanced waterproofing.
14. The advantage that is **not associated** with warm mixed asphalt is: **Increased binder ageing**. Warm mixed asphalt technologies offer advantages such as energy savings, decreased emissions, and decreased fumes. However, they do not result in increased binder aging compared to hot mixed asphalt.
15. To simulate the aging of asphalt binder after 5-year service, the appropriate test to conduct is: **RTFO (Rolling Thin Film Oven) test**. The RTFO test subjects the asphalt binder to elevated temperature and airflow, simulating the oxidative aging that occurs over time during service conditions. This test helps evaluate the long-term aging characteristics of the binder.
Learn more about temperature here
https://brainly.com/question/15969718
#SPJ11
QUESTION 1 Most common and most widely used source encoding techniques for digital communication are Run-length, Huffman and Lempel-Ziv Algorithms. Write a short paper on the three algorithms. The paper should consist of Title, Abstract, Introduction, and Conclusion. [20 marks] [CLO1-PLO3:C4] QUESTION 2 Traditional phone calls work by allocating an entire phone line to each call. With VoIP, voice data is compressed, and with VoIP on your computer network you can add telephones and increase call capacity without running additional cabling. Write a comparative analysis paper on Voice over Internet Protocol (VoIP) vs traditional phone calls. The paper should consist of Title, Abstract, Introduction, Comparison between VoIP and Traditional Phone and Conclusion. QUESTION 3 A network has five basic components such as clients, servers (host computer), channels (network circuit). interface devices and operating systems (network software). Analyse each component by writing a short article. The article should consist of Title, Abstract, Introduction, Description of Five Network Components and Conclusion
Title: Review on Lossless Compression Techniques.
Abstract: In the present world data compression is used in every field. Through data compression, the bits required to represent a message will be reduced.
1. Introduction
Data compression is widely used in all fields. The main aim of data compression is to minimize the number of bits required code an information or data , which helps minimize the hardware(inventory) required to transfer or store the given data. It encompasses many hardware and software techniques which have only one in common that is compressing the data.
1.1 Lossy compression: Lossy compression as the name says, these methods encounter some loss of information while decompressing the compressed information.
1.2 Lossless compression: Lossless compression techniques code the data and transfer them accurately; there will not be any kind of loss in data while decompressing the compressed information. This is applied to store database records, spreadsheets, word files etc.
2. BACKGROUND OF LOSSLESS COMPRESSION TECHNIQUES
In Huffman coding a symbol which is higher probability of occurrence generates less number of bits; a symbol with less probability of occurrence generates higher number of bits to transfer.
Adaptive Huffman coding
Adaptive Huffman coding was first published by Faller (1973) and later Gallager (1978), independently. In 1985 Knuth made a little modification and so the algorithm was FGK.
The general flow of the program using adaptive Huffman coding for encoding is shown in figure.1.
The drawbacks of adaptive Huffman coding are: -
1. It is very complex to construct the binary tree which in turn makes it unsuitable for sensor nodes 6.
2. As it does not know anything about the data at the initial stage so it will not work efficiently for Compression.
Arithmetic Coding:
Arithmetic coding is a lossless compression process. It generates variable length codes. Generally, a string is taken and every letter is coded with a fixed number of bits. In this type of coding less frequently occurred letters/symbols are given with larger bit representation and more frequently occurred symbols/letters are coded with fewer bits as to save the memory.
3. ALGORITHMS
3.1. ADAPTIVE HUFFMAN CODING:
1. First time if the symbols occurs then NYT (not yet transmitted) is split and if the symbol already exists then add to the symbol.
2. In tree always left side weights < right side weights, if it is not then we have to swap the left child and right chid.
3. We have assigned logic 0 to the left child of the tree and logic 1 to right chid of the tree.
4. We have to simultaneously code the symbol.
5. To code the symbol we have to follow the following steps:-
• If 1≤ position of symbol (k) ≤ 2r [r=10, e=4 for English alphabets] then symbol is encoded as (e+1) bit and binary equivalent of (k-1).
• Else, Position of symbol (k) ≥ 2r then symbol is encoded as e bit and binary equivalent of (k-r-1).
3.2. Arithmetic coding
1. First divide the tag interval {0, 1} into two parts they are {0, 0.5} and {0. 5, 1} .
2. We consider {0, 0.5} as lower half and {0.5,1} as upper half.
3. We consider {0,0.5}as lower half and {0.5,1} as upper half.
4. Pick first symbol from the input sequence and find upper limit and lower limit of the symbol using the following formula.
ln = l(n-1) +(u(n-1)-l(n-1))fx(Xn-1)
ln = l(n-1)+(u(n-1)-1(n-1))fx(Xn)
Where ln is lower limit, is upper limit and f(x) is probability density function. Then check whether the generated limits are lying in which half, if the limits lie in lower half we will transmit '0' , if they lie in upper half then transmit '1'. And then rescale the limits.
1. If they lie in lower half perform (2*A) operation, if they lie in upper half then perform (2(A-0.5)) operation and then transmit '0' or '1' according to that.
2. Repeat above two steps till the calculated lower and upper limits fall neither in lower and upper bound
3. If the upper and lower limits doesn't constrain to either of the lower and upper bound then stop this process and pick the next symbol.
4. By performing this for all the symbols in the sequence then a unique binary code is generated for the sequence.
4. OBSERVATIONS :
The following inputs are considered and we performed adaptive Huffman coding and arithmetic coding on given message bits that are: -
1. ACBA
2. ABBDC
Table:1- Adaptive Huffman coding and arithmetic coding on given message bits
Table:1- Adaptive Huffman coding and arithmetic coding on given message bits S. No. Message Adaptive Huffman coding Arithmeti
It is observed that when probability of the symbols is not in the neighbourhood of each other, then arithmetic coding yields less number of bits, so it is preferable.
5. Conclusion :
For two specific sequences with random probabilities adaptive Huffman coding requires more number of bits than arithmetic coding.
To know more about Data compression:
https://brainly.com/question/31558512
#SPJ4
7e. a = 8
(e) (10 pts.) z = diagram. Consider a discrete-time linear time-invariant system with single poles at z = and a double zero at z = 0. Determine |H(e)\/|H(eo). Hint: Draw the pole-zero and
The magnitude response of the discrete-time linear time-invariant system with single poles and a double zero can be determined by analyzing the pole-zero plot and applying the appropriate formula.
To determine the magnitude response[tex]|H(e)|/|H(eo)|[/tex] of the given system, we need to analyze its pole-zero plot. The poles and zeros of a system represent the frequencies at which the system has maximum response or attenuation.
In this case, the system has a single pole at z = and a double zero at z = 0. The pole at z = represents a frequency at which the system exhibits a maximum response, while the zero at z = 0 represents a frequency at which the system has zero response.
The magnitude response [tex]|H(e)|/|H(eo)|[/tex] can be calculated by taking the absolute value of the product of the distances from the zeros and poles to the point on the complex plane corresponding to the frequency of interest. In this case, since the frequency of interest is not specified, we need more information to determine the exact magnitude response.
To fully determine the magnitude response, additional details about the system or specific frequencies of interest are required. This could include the transfer function, the sampling rate, or the specific frequencies at which the response is being evaluated.
Learn more about magnitude response
brainly.com/question/32671627
#SPJ11
The Block Diagram Shown In Fig.5 Represents A Particular Feedback Control System. Simplify The (10) Block Diagram To
The given block diagram in represents a particular feedback control system. Simplify the (10) block diagram to The simplified block diagram of the feedback control system is shown below: Feedback control system block diagram
The block diagram represents the feedback control system as follows:Inputs: e(t)Outputs: y(t)Signal flow: e(t) → G(s) → f(t) → H(s) → y(t)For simplifying the given block diagram, we will use the following basic blocks:Unity feedback system: A block diagram of unity feedback system is shown below: Unity feedback control system block diagramSimplifying the given block diagram using the above basic block, we get the simplified block diagram of the feedback control system as shown below: Feedback control system block diagram (simplified)
The simplified block diagram of the feedback control system is shown below: Feedback control system block diagram And The block diagram represents the feedback control system as follows: Inputs: e(t)Outputs: y(t)Signal flow: e(t) → G(s) → f(t) → H(s) → y(t)For simplifying the given block diagram, we will use the following basic blocks:Unity feedback system: A block diagram of unity feedback system is shown below: Unity feedback control system block diagram Simplifying the given block diagram using the above basic block, we get the simplified block diagram of the feedback control system as shown below: Feedback control system block diagram (simplified)
To know more about block diagram visit:
https://brainly.com/question/13441314
#SPJ11
Note: please provide full details of answers for a and b & c
a. Explain the working of a full-adder circuit using a decoder with the help of truth-table and diagram
b. Realise the Boolean function using an 8 X 1 MUX
C . Give any two points to compare Decoders and Encoders and draw their block diagram
Working of a full-adder circuit using a decoder with the help of truth-table and diagram A full adder circuit is an arithmetic logic unit that is used in digital circuits for performing mathematical computations. It c
An be created using different types of logic gates such as OR, AND, XOR, and NAND gates. However, one of the most efficient ways to create a full adder circuit is by using a decoder. Here is a truth table for a full adder circuit using a decoder and its corresponding circuit diagram:Truth tableA B Cin Cout S0 0 0 0 0 01 0 0 0 1 10 1 0 0 1 01 1 0 1 0 10 0 1 0 1 10 1 1 1 1 1Circuit diagramHere, A, B, and Cin are the input bits, whereas S and Cout are the output bits. The decoder is used to simplify the circuit by producing two outputs, Cout and S. The first output, Cout, is the carry output, and the second output, S, is the sum output. The decoder is used to control the logic gates by providing the appropriate signals to the inputs of the logic gates.
To know more about computations visit:-
https://brainly.com/question/33214480
#SPJ11
Consider the following statements about inheritance in Java? 1) Private methods are visible in the subclass 2) Protected members are accessible within a package and in subclasses outside the package. 3) Protected methods can be overridden. 4) We cannot override private methods. Which of the following is the most correct? a. 2 and 3 b. 2,3 and 4
c. 1 and 2 d. 1,2 and 3
Consider the following Java inheritance statements:1) In the subclass structure, private methods are visible.2) Protected members can be accessed from within or outside for a particular package.3) Protected methods are overridable.4) We are unable to override private methods. The proper answers are 2, 3, and 4.
What is inheritance?
Inheritance is one of the fundamental principles of object-oriented programming (OOP). When a class extends another class, the subclass inherits the properties of the superclass.
Private methods are hidden in the subclass.
Protected members can be accessed both within and outside of a package.
Protected methods can be overridden. We cannot override private methods.
Therefore, options 2, 3, and 4 are correct.
Learn more about inheritance:
https://brainly.com/question/15078897
#SPJ11
Given the language L = {w € {0, 1}* | w contains at least three 1s}, (a) show a context-free grammar that generate L. (b) construct a push-down automta using the top-down approach. Solution::
The language L = {w € {0, 1}* | w contains at least three 1s} can be generated using a context-free grammar and a push-down automata. Let's take a look at both of them:
Context-free grammar:
S → 0S | 1A | εA → 0A | 1B B → 0B | 1C C → 0C | 1 | εHere, S, A, B, and C are non-terminal symbols, and 0 and 1 are terminal symbols. This grammar generates strings that contain at least three 1s. Let's see how it works: S → 1A → 11B → 111C → 111S → 101A → 1011B → 10111C → 10111S → 1001A → 10011B → 100111C → 100111S → εA → εPush-down automata: The push-down automata can be constructed using the top-down approach.
The PDA has a stack, an initial state, a set of final states, and a set of transition rules. The transition rules are defined as follows: (q0, ε, ε) → (q1, S) (q1, 0, ε) → (q1, 0) (q1, 1, ε) → (q2, 1) (q2, 0, ε) → (q2, 0) (q2, 1, ε) → (q3, ε)Here, q0 is the initial state, q3 is the final state, and S is the start symbol. When the automata reads a 1, it pushes it onto the stack.
To know more about language visit:
https://brainly.com/question/32089705
#SPJ11
for a uniformly distribution random variable between-2 and 4 evaluate the mean mx and the variance sigmaxsquare
The variance of the uniformly distributed random variable is 3.
The mean (mx) of a uniformly distributed random variable between -2 and 4 is given by:
mx = (b + a)/2
where a = -2 and b = 4mx = (4 + (-2))/2mx = 2/2mx = 1
Therefore, the mean of the uniformly distributed random variable is 1.
The variance (sigma x square) of a uniformly distributed random variable between -2 and 4 is given by:
sigma x square = (b - a)^2/12 where a = -2 and b = 4 sigma x square = (4 - (-2))^2/12 sigma x square = 6^2/12 sigma x square = 36/12 sigma x square = 3
Therefore, the variance of the uniformly distributed random variable is 3.
To know more about variance visit:
https://brainly.com/question/31432390
#SPJ11
Problem: CLO 03→ PLO 02 → C03 Marks: 20 An analog communication system is to be designed for transmission of human voice when the available bandwidth is 10 kHz. You are required to construct one or more analog modulation schemes that could be used under given circumstances. Justify your choice(s) in terms of bandwidth, impact of noise, transmitter efficiency, ease of deployment and audio quality of received signal.
The FM scheme, on the other hand, is less sensitive to power fluctuations than the AM scheme. The FM modulation scheme is simple to deploy and is commonly used for voice transmission, so it is easy to deploy.
Analog modulation schemes that can be used for the transmission of human voice are amplitude modulation (AM), frequency modulation (FM), and phase modulation (PM). The bandwidth of the signal must be considered in the modulation scheme, which is 10 kHz in this case.
Amplitude Modulation (AM) is a popular modulation scheme that is simple to implement. The bandwidth of an AM signal is twice that of the baseband signal. As a result, a 5 kHz baseband signal modulated with AM produces a signal with a bandwidth of 10 kHz. The audio quality of the AM signal is moderate, but it is affected by noise and interference. FM is a second modulation scheme.
To know more about transmission visit:-
https://brainly.com/question/32666848
#SPJ11
Based on the following code segments, which is/are of the following correct statement(s)? Choose THREE answers. public class TestOveloadingi public static void main (String 11 args) Horse h new Horse(); System.out.println (h.eat()); class Animal ( void eat() ( System.out.println("Generic Animal Eating Generically"): 1 String eat () ( System.out.println("This method return string") return "This is the returned string": class Horse extends Animal ( void eat ()1 System.out.println("Generic Animal Eating Generically": This code will not be compiled because the eat() method has no return string in the subclass We can fix the code by making the method in line 12 receive any data type variable and accordingly fix line 4 This code will not be compiled because there are no overloading methods by changing the return type of the method We can fix the error by renaming the method eat() on line 12 and accordingly fix line 4 5 24855
Here, the class Test Oveloading consists of three classes: Test Oveloading, Animal and Horse. The main class has created an object h of the Horse class, and calling the eat() method.
Class Animal consists of an eat() method that returns a string "Generic Animal Eating Generically". The class Horse extends the class Animal. It has overridden the eat() method of Animal with its own eat() method which prints the message "Generic Animal Eating Generically".
Based on the given code segments, the following correct statements are: This code will not be compiled because the eat() method has no return string in the subclass. We can fix the code by making the method in line 12 receive any data type variable and accordingly fix line 4.
To know more about Oveloading visit:-
https://brainly.com/question/29732747
#SPJ11
Write a Java program to calculate the revenue from a sale based on the unit price and quantity of a product input by the user. The discount rate is 10% for the quantity purchased between and including 100 and 120 units, and 15% for the quantity purchased greater than 120 units. If the quantity purchased is less than 100 units, the discount rate is 0%.
You will provide a method called calculateRevenue that takes in two arguments, the unit price and quantity of a product. (Use correct data types). The calculateRevenue method will calculate the revenue from the sale and the discount that was given.
The inputs will be handled in the main method which will call the method calculateRevenue and pass it the revenue and quantity.
See the example output as shown below:
Enter unit price: 25
Enter quantity: 110
The revenue from sale: $2475.00
The discount rate you received is 10%.
The program assumes valid input from the user (positive unit price and quantity). Error handling for invalid input is not included in this example.
Here's the Java program that calculates the revenue from a sale based on the unit price and quantity of a product input by the user:
import java.util.Scanner;
public class RevenueCalculator {
public static void main(String[] args) {
Scanner scanner = new Scanner(System.in);
System.out.print("Enter unit price: ");
double unitPrice = scanner.nextDouble();
System.out.print("Enter quantity: ");
int quantity = scanner.nextInt();
calculateRevenue(unitPrice, quantity);
}
public static void calculateRevenue(double unitPrice, int quantity) {
double revenue = unitPrice * quantity;
double discountRate = 0;
if (quantity >= 100 && quantity <= 120) {
discountRate = 0.1;
} else if (quantity > 120) {
discountRate = 0.15;
}
double discount = revenue * discountRate;
double totalRevenue = revenue - discount;
System.out.printf("The revenue from sale: $%.2f%n", totalRevenue);
System.out.printf("The discount rate you received is %.0f%%%n", discountRate * 100);
}
}
In this program, the main method prompts the user to enter the unit price and quantity of the product. It then calls the calculateRevenue method, passing the unit price and quantity as arguments.
The calculateRevenue method calculates the revenue by multiplying the unit price and quantity. It determines the discount rate based on the quantity purchased. If the quantity is between 100 and 120 (inclusive), the discount rate is set to 10%. If the quantity is greater than 120, the discount rate is set to 15%. Otherwise, for quantities less than 100, the discount rate is 0%.
The method calculates the discount by multiplying the revenue with the discount rate. It then subtracts the discount from the revenue to get the total revenue. Finally, it displays the total revenue and the discount rate to the user.
Know more about Java program here:
https://brainly.com/question/2266606
#SPJ11
Clearly explain why collision detection is not possible in wireless local area networks. Clearly explain why the timing intervals SIFS, PIFS, and DIFS have been ordered as SIFS < PIFS < DIFS in the CSMA/CA protocol. More past exam questions …Clearly explain the hidden terminal problem.
Collision detection is not possible in WLANs due to the half-duplex nature of wireless transmission. WLANs use collision avoidance protocols like CSMA/CA, with prioritized timing intervals (SIFS, PIFS, DIFS), to ensure reliable communication and address the hidden terminal problem.
Collision detection is not possible in wireless local area networks (WLANs) because the wireless medium is half-duplex, meaning that it can only transmit data in one direction at a time.
This means that two devices can not transmit data at the same time, making it impossible for collision detection to occur. Instead of collision detection, WLANs use collision avoidance protocols such as CSMA/CA to ensure reliable communication.
The timing intervals SIFS, PIFS, and DIFS have been ordered as SIFS < PIFS < DIFS in the CSMA/CA protocol to ensure that higher-priority data has a greater chance of being transmitted successfully.
SIFS (Short InterFrame Space) is the shortest time interval, used for communication between devices in the same Basic Service Set (BSS) that have successfully transmitted data. PIFS (Point Coordination Function Interframe Space) is a slightly longer interval used for communication between devices that need to gain access to the medium.
Finally, DIFS (Distributed Coordination Function Interframe Space) is the longest interval used when devices are competing for access to the medium. This ordering allows devices with higher-priority data to access the medium more quickly.
The hidden terminal problem occurs in wireless networks when two devices are in range of the same access point, but not in range of each other. When one device transmits data, the other device does not receive the transmission and assumes that the medium is idle.
The second device then begins transmitting data, leading to a collision when the transmissions reach the access point. To solve this problem, WLANs use techniques such as Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) to ensure that devices are aware of other transmissions on the network before attempting to transmit their own data.
Learn more about WLAN : brainly.com/question/27975067
#SPJ11
The code below implements a function QU2 which has an input arr of type Array of Int and returns an integer. function QU2 (arr) { var i in Int var anInt in Int anInt <-- 0 for (i <-- 2 to 4) { if (AT (i,arr) > 10) then { anInt <-- anInt + 1 } } return 4 * an Int (a) (i) Trace the values of the variables i and anInt after each execution of the body of the for loop as this code is executed when the input array arr is [21, 12, 15, 3, 18]. [3] (ii) Write down the value that is returned for this input. [1] (b) To ensure that the given code is valid, suggest a pre-condition that the input arr should satisfy. [2]
The code given above implements a function QU2 which takes an input arr of type Array of Int and returns an integer.The tracing of values of the variables i and anInt after each execution of the body of the for loop as this code is executed when the input array arr is [21, 12, 15, 3, 18]
is:i --> 2, anInt --> 1 (because AT(2,arr) > 10) i --> 3, anInt --> 2 (because AT(3,arr) > 10) i --> 4, anInt --> 3 (because AT(4,arr) > 10)Finally, it returns 4 * anInt = 4 * 3 = 12.For the given code to be valid, one of the preconditions that the input array arr should satisfy is that it should have at least 5 elements.
This is because the code involves accessing the elements of the array at the 2nd, 3rd, and 4th positions which are all greater than or equal to 2 and less than or equal to 4, as indicated in the for loop. Therefore, if arr has less than 5 elements, the code would result in an error.
To know more about execution visit:
https://brainly.com/question/11422252
#SPJ11
Which is true about the output of the following code? Select all correct answers, Choose TWO answers. class Bike ( int speedlimit=90; } class Honda3 extends Bike int speedlimit=150; public static void main(String args[]) { Bike obj=new Honda3(); System.out.println (obj.speedlimit); } The output will be 150 because the obj is instance of the Honda class The output will be 90 because the speedlimit cannot be overridden 0 The output will be 90 because the obj is instance of the Bike class The output will be 150 because the speedlimit of Bike has been overridden
The output of the following code will be 150 because the speedlimit of Bike has been overridden. This is because obj is an instance of the Honda3 class and the speedlimit of Bike has been overridden.Explanation:In the given code snippet,
we are trying to extend a class named Bike and override the value of a variable named speedlimit in the subclass Honda3.The Honda3 subclass is derived from the Bike class. The value of speedlimit in the Bike class is 90, while the value of speedlimit in the Honda3 class is 150.
A new instance of the Honda3 class is created in the main method and it is assigned to an object of Bike type named obj. Then, the value of speedlimit is printed using the println() method.The speedlimit variable in the Bike class is a public variable that can be accessed using the object of the subclass Honda3. When obj.speedlimit is executed, the speedlimit variable of the Honda3 class is returned instead of the Bike class. Thus, the output of the program will be 150 as the obj is instance of the Honda3 class.The main answer is: The output will be 150 because the speedlimit of Bike has been overridden.The correct options are:a) The output will be 150 because the obj is instance of the Honda3 class.b) The output will be 90 because the speedlimit of Bike cannot be overridden.
TO know more about that output visit:
https://brainly.com/question/14227929
#SPJ11
The Car Maintenance team wants to learn how many times each car is used in every month and day to organize their maintenance schedules. The team wants a table with the following column names and information: • Car ID • Month • Day • Count You need to create a summary table using the WITH ROLLUP modifier and grouped by the specific column names, listed above, and send the data back to the team. Task Query the frequency of each car's use by month and day Task 3: The Driver Relationship team wants to analyze drivers and their car usages in Instant Ride for the month October. Thus, they want to focus on each driver and respective car allocation occurred. In more detail, the team requires the DRIVER_ID and the CAR_ID with their usage counts as the TOTAL column for the travels occurred in the month of October. Since the team wants to also learn the total number of the travels by the drivers you need to use GROUP BY ROLLUP functionality. Task Create a query to analyze car usage for the month of October. Task 4: As a part of marketing strategy, the Marketing team continuously conducting an advertising campaign on different channels. The team would like to know how this campaign is impacting the overall rides being taken through the InstantRide, specifically the rides which cost $5 or more. You need to send the number of travels calculated for each day and month with their totals using Month, Day and Count column names. Furthermore, you can name your subquery as PREMIUM_RIDES to work only with the travels with the price of 5 or higher. Task Calculate the number of premium rides given for each day and month.
Task 1: Query the frequency of each car's use by month and dayIn order to query the frequency of each car's use by month and day, a summary table with the following column names and information is required:• Car ID• Month• Day• Count. The summary table should be created using the WITH ROLLUP modifier and grouped by the specific column names listed above.
The following SQL query can be used to achieve this:SELECT car_id, month, day, COUNT(*) AS countFROM car_usage_tableGROUP BY car_id, month, day WITH ROLLUPTask 3: Create a query to analyze car usage for the month of October The Driver Relationship team wants to analyze drivers and their car usages in Instant Ride for the month of October.
They require the DRIVER_ID and the CAR_ID with their usage counts as the TOTAL column for the travels occurred in the month of October. The team wants to learn the total number of the travels by the drivers. GROUP BY ROLLUP functionality should be used to achieve this.The following SQL query can be used to achieve this:
SELECT driver_id, car_id, COUNT(*) AS totalFROM car_usage_tableWHERE month = 'October'GROUP BY driver_id, car_id WITH ROLLUPTask 4: Calculate the number of premium rides given for each day and monthThe Marketing team wants to know how their advertising campaign is impacting the overall rides being taken through Instant Ride.
Specifically the rides that cost $5 or more. The number of travels calculated for each day and month with their totals should be sent using Month, Day, and Count column names. A subquery can be named as PREMIUM_RIDES to work only with the travels with the price of 5 or higher.The following SQL query can be used to achieve this:SELECT month, day, COUNT(*) AS countFROM (SELECT date, fareFROM ride_tableWHERE fare >= 5) AS PREMIUM_RIDESGROUP BY month, day.
To know more about listed visit:
https://brainly.com/question/32132186
#SPJ11
ALAN network (called LAN #1) includes 4 hosts (A, B, C and D) connected to a switch using static IP addresses (IP_A, IP_B, IP_C, IP_D) and MAC addresses (MAC_A, MAC_B, MAC_C, MAC_D). The LAN #1 network is connected to a second LAN network (called LAN #2) by a router. The gateway IP address in LAN #1 network is called E and has IP E as IP address, and MAC_E as MAC address. The second network includes two hosts F and G with IP addresses IP F and IP_G, and MAC addresses MAC F and MAC_G We assume that so far no communication took place between all hosts in both networks. Also, we assume that host A pings host B, then host B pings host A, then host B pings host D. • How many ARP request and response packets have been generated: Number of generated ARP request packets: 2 Number of generated ARP response packets: 2 Number of generated ARP request packets: 1 Number of generated ARP response packets: 3 Number of generated ARP request packets: 4 • Number of generated ARP response packets: 4 Number of generated ARP request packets: 3 Number of generated ARP response packets: 3 Number of generated ARP request packets: 2 Number of generated ARP response packets: 4 None of them. We assume that a LAN network has 4 hosts (A, B, C and D), E is the gateway (router), and hosts F and G are external hosts. Host A is the security administrator's host and wants to detect the hosts' NIC cards set to the promiscuous mode. Can the below ARP packet be used that task? ARP operation 1 Source IP A Source MAC A Destination IP 0 Destination MAC 0 Destination MAC FF:FF:FF:00:00:00 Source MAC A MAC type (IP or ARP) ARP 1. Yes 2. NO
Yes, the ARP packet given below can be used to detect the NIC cards of the hosts set to the promiscuous mode:ARP operation 1 Source IP A Source MAC A Destination IP 0 Destination MAC 0 Destination MAC FF:FF:FF:00:00:00 Source MAC A MAC type (IP or ARP) ARP ARP packets are generally used to identify IP address to MAC address mappings on a network.
ARP packets are sent in broadcast mode and contain source and destination MAC addresses and IP addresses. When the destination MAC address is a broadcast address, the packet is broadcasted to all devices on the network, and every host on the network will receive and process the packet.
To identify the host's NIC card set to the promiscuous mode, the security administrator's host sends the ARP request to the destination MAC address of FF:FF:FF:00:00:00 with the source IP address and MAC address of the security administrator's host.
This ARP request packet forces every device in the network to respond with its MAC address in order to match the given broadcast address FF:FF:FF:00:00:00, and the security administrator's host can verify and list all of the responses it receives.
To know more about identify visit:
https://brainly.com/question/13437427
#SPJ11
For the signal, x(t), shown to
the right,
a. Write a single expression valid
for all t, in terms of u(t) and
line equations
b. Sketch f(t) = x(t+2) and g(t) =
x(2t+4)
The signal x(t) can be represented by the following expression:x(t) = [2u(t-1) - 2u(t-3) + u(t-6) - u(t-7)] + 2[u(t-4) - u(t-5)]ExplanationThe given signal is a sum of different line segments, and the u(t) is used to determine the starting and end points of the line segments.
There are two line segments that are equal and each one of them goes from 4 to 5 and 1 to 3 respectively. This is shown in the expression by 2[u(t-4) - u(t-5)]The second line segment is from 6 to 7 with a slope of 1.
This is shown in the expression by u(t-6) - u(t-7)The first line segment is from 1 to 3 with a slope of -2. This is shown in the expression by 2u(t-1) - 2u(t-3)b) Explanationf(t) = x(t+2)When you compare this to the original signal, x(t), this is a delay of 2 units to the left. Therefore, the line segments will be shifted to the left by 2 units.g(t) = x(2t+4)When you compare this to the original signal, x(t), this is a compression in the horizontal axis by a factor of 2 and a delay of 4 units to the left. Therefore, the line segments will be shifted to the left by 4 units. They will also be compressed horizontally by a factor of 2.
TO know more about that expression visit:
https://brainly.com/question/28170201
#SPJ11
A high power energy storage system using supercapcitor modules is to be designed for a UPS (uninterrupted power supply) to meet short term electric power needs of a data center. The UPS has a dc bus voltage, = 700 and power rating, P 0 = 400W. The supercapacitor storage unit supplies power for a time, T H = 20 , and it is charged back in a shorter charge time T H = 5 . The inverter interface with storage system has an efficiency = 98 % .
(a) Determine the maximum and minimum operating voltage if the supercapacitor module is connected to the UPS dc bus via a bi-directional dc-dc converter with a maximum current capability, 0 mx = 900.
(b) Design the energy storage module according to the above parameters by taking into account the EOL effect on the initial SOL design parameters. The design should include
(i) Nominal module capacitance
(ii) Nominal module voltage rated 15% higher than maximum operating voltage
(iii) The number of series and parallel connected cells.
For the design, use commercially available EDLC supercapacitor cells K2-2500F/2.8V from Maxwell. Use the coefficient 0 = 0.8 for these cells in the module.
(c) After the design, predict the equivalent series resistance (ESR, 0 ) of the module.
The objective is to meet the short-term electric power needs of the data center by providing uninterrupted power supply through a high power energy storage system utilizing supercapacitor modules.
What is the objective of designing a high power energy storage system using supercapacitor modules for a data center's UPS?The given paragraph describes the design of a high power energy storage system using supercapacitor modules for a data center's UPS. The system has specific requirements such as a dc bus voltage of 700V, power rating of 400W, and specific charge and discharge times. The efficiency of the inverter interface is also provided as 98%.
(a) The task is to determine the maximum and minimum operating voltage of the supercapacitor module when connected to the UPS via a bi-directional dc-dc converter with a maximum current capability.
(b) The design of the energy storage module needs to be carried out considering the given parameters and taking into account the End-of-Life (EOL) effect on the initial State-of-Life (SOL) design parameters.
The design should include the nominal module capacitance, nominal module voltage rated 15% higher than the maximum operating voltage, and the number of series and parallel connected cells.
The commercially available EDLC supercapacitor cells, K2-2500F/2.8V from Maxwell, should be used for the design, considering a coefficient of 0.8 for these cells in the module.
(c) After the design is completed, the task is to predict the equivalent series resistance (ESR, θ) of the module. This parameter is important for analyzing the performance and efficiency of the energy storage system.
Learn more about storage system
brainly.com/question/32632602
#SPJ11
Give the instruction that will do the following. 9 10. Put the constant value "12" into the register r0. 10. After incrementing r2 by eight, get the value from memory pointed to by the address contained in r2 and put it into r0.
The instructions that are given here are explained below in explanation part.
You can utilise assembly language instructions to carry out the specified instructions. Here are the steps to follow in order to get the result you want:
Load the constant value "12" into register r0:MOV r0, #12
Increment r2 by eight:ADD r2, r2, #8
Get the value from memory pointed to by the address in r2 and store it in r0:LDR r0, [r2]
Thus, these instructions suppose that you have an assembly language environment.
For more details regarding assembly language, visit:
https://brainly.com/question/31231868
#SPJ4
Use the MATLAB imshow() function to load and display the image A stored in the image.mat file, available in the Project Two Supported Materials area in Brightspace. For the loaded image, derive the value of k that will result in a compression ratio of CR 2. For this value of k, construct the rank-k approximation of the image. CR= mn k(m+n+1)
The rank-k approximation of the image can be computed as the product of the left singular vectors, singular values, and right singular vectors the rank-k approximation of the image can be displayed using the `imshow()` function.
To display the image A that is stored in the image. mat file, available in the Project Two Supported Materials area in Brightspace, and to derive the value of k that will result in a compression ratio of CR 2, we can use the following MATLAB code:```matlab% Load the image from the image. mat file. load ('image. mat');%Display the loaded image.
The `k` value is calculated using the given formula, `CR = mn/(m+n+1/k)`.Once we have the value of k, we can construct the rank-k approximation of the image using the `svds()` function in MATLAB, which performs a singular value decomposition on the matrix `A` and returns the `k` largest singular values and corresponding left and right singular vectors.
To know more about function visit:
https://brainly.com/question/17216645
#SPJ11
For tension members: Should there be more than one row of bolt holes in a member, it is often desirable to stagger them in order to provide as large a net area as possible at any one section to resist the applied load. True O False
**False.**Aligning them in a straight line allows for the largest net area at any section, ensuring the member's ability to resist the applied load.
In tension members, when there are multiple rows of bolt holes in a member, it is generally not desirable to stagger them. Instead, they are typically aligned in a straight line. Staggering the bolt holes would result in a reduction of the net area available to resist the applied load, which is contrary to the goal of maximizing the net area.
When bolt holes are staggered, it creates a reduction in the effective net area due to overlapping or interference between the holes. This decreases the overall strength and load-carrying capacity of the member. Therefore, it is important to align the bolt holes in a tension member to ensure the maximum net area is available to resist the applied load.
By aligning the bolt holes in a straight line, the full cross-sectional area of the member can be utilized, providing the maximum possible net area at any given section. This design approach helps to ensure the optimal strength and load-carrying capacity of the tension member, allowing it to effectively resist the applied tensile forces.
In conclusion, it is not desirable to stagger the bolt holes in a tension member. Aligning them in a straight line allows for the largest net area at any section, ensuring the member's ability to resist the applied load.
Learn more about straight line here
https://brainly.com/question/13440336
#SPJ11
Using the testbed database:
Create a view called LastHireDate for the GatorWareEmployee table that displays the date the most recent employee was hired (if necessary recreate the GatorWareEmployee table first using the code provided in the folder on the Azure desktop). Provide both the code listing for the view, the code to run the view, and a screenshot of the view being run.
Explain how views can enhance database security.
Testbed database is used to perform the testing of the database-related activities. A view is a type of virtual table that helps in retrieving the data from one or more tables and create a new table, which is a subset of the original table. The view works like a filter, which selects specific data from the tables.
Views can enhance database security by providing the following advantages:• Simplification: Views simplify the user interface by hiding the complexity of the database schema.• Data hiding: Views can be used to hide sensitive or confidential data in a database by restricting access to specific rows and columns. This helps in protecting the data from unauthorized access.• Limited access: Views can be used to provide limited access to the database schema.
Restrict data: Views can be used to restrict the data that is displayed to the user. This helps in ensuring that users can only access the data that is relevant to their work or department. Following is the code listing to create a view called LastHireDate for the GatorWareEmployee table:CREATE VIEW LastHireDateASSELECT TOP 1 HireDateFROM GatorWareEmployeeORDER BY HireDate DESCHere is the code to run the view:SELECT * FROM LastHireDateFollowing is the screenshot of the view being run:Screenshot of the view
To know more about specific data visit :
https://brainly.com/question/30557347
#SPJ11
Based on the last given, each group is entitled to choose only ONE question as assigned. in. v. i Design of a 4-bits serial in serial out shift register using D flip flop Design of a 4-bits serial in parallel out shift register using D flip flop m. Design of a 3-bits counter using JK flip flop vi vi ASSIGNMENT I PART B Design of a 4-bits counter using JK flip flop Design of a 1/4 frequency divider using D tlip flop Design of a 1/4 frequency divider using JK flip flop Design of a 1/8 frequency divider using D flip flop Design of a 1/8 frequency divider using JK flip flop 2 The video will be evaluated based on these criteria i Introduction Methodology Logic Diagram Truth table Results ASSIGNMENT 1 PART B 3:21/3122 iv. v. vi Discussion 1/4 frequency divider using D flip flop
The one chosen among the other options is: Design of a 4-bit serial-in, serial-out shift register using D flip-flops:
What is the use of the flip-flops?A sequential circuit which has the capability to save and move a sequence of 4 bits is known as a serial-in, serial-out shift register.
The Required Components are:
Four D flip-flops (DFF)Clock signal (CLK)Serial input (SI)Serial output (SO)The design Steps are:
Link or join the serial input (SI) to the data input (D) of the initial D flip-flop.Link the Q output of every D flip-flop to the succeeding flip-flop's D input in a chain.Establish a connection between the CLK signal and the C input of each D flip-flop.The final flip-flop's result serves as the serial output (SO).Learn more about flip-flops from
https://brainly.com/question/27994856
#SPJ4
Calculate CO2 emission from a 1 passenger private small airplane using the data given in the Table below. ܐܝܟ Assume: • CO2 emission from aviation fuel = 3.15 kg/kg of fuel- • Density of aviation fuel = 800 g/L Table 4.5 Energy efficiency of air and water passenger modes Mode Average energy usage Typical passenger load Capacity load in miles per gallon Passengers Miles per gallon Passengers Miles per gallon (litres per 100km) passenger passenger Air Private small airplane 12.6 (18.7) 12.6 50.4 (Cessna 172)
The CO2 emission from a 1-passenger private small airplane cannot be calculated accurately without specific data on passenger load and capacity load in miles per gallon.
The CO2 emission from a 1-passenger private small airplane can be calculated using the provided data. Given that the average energy usage of the mode is 12.6 miles per gallon (liters per 100 km), and the CO2 emission from aviation fuel is 3.15 kg/kg of fuel, we can proceed with the calculation.
First, we need to convert the energy usage from miles per gallon to liters per 100 km for consistency. Assuming 1 gallon is approximately 3.78541 liters and 1 mile is approximately 1.60934 kilometers, we can convert 12.6 miles per gallon to liters per 100 km as follows:
Energy usage (liters per 100 km) = (12.6 miles per gallon) * (1 gallon / 3.78541 liters) * (100 km / 1.60934 miles)
Once we have the energy usage in liters per 100 km, we can calculate the CO2 emission for the 1-passenger private small airplane using the density of aviation fuel.
CO2 emission (kg) = Energy usage (liters per 100 km) * (800 g/L) * (3.15 kg/kg of fuel)
By substituting the converted energy usage into the formula, we can find the CO2 emission from the airplane.
Please note that the provided table only includes information about energy efficiency and passenger load, but the specific data for passenger load and capacity load in miles per gallon is not given for the private small airplane. To proceed with the calculation, we would need that specific information.
Keywords: CO2 emission, 1-passenger private small airplane, aviation fuel, energy efficiency, passenger load, density of fuel
Keywords (supporting answer): calculation, energy usage, miles per gallon, liters per 100 km, CO2 emission from fuel, conversion, density of aviation fuel
Learn more about CO2 emission here
https://brainly.com/question/31228087
#SPJ11
Create a tone of 2 kHz and mix it with a music file of 30 seconds. You are then required to create a notch filter to notch out the annoying interference using simple pole-zero approach. Notch out the tone from the corrupted audio file and record the result.
In order to create a tone of 2 kHz and mix it with a music file of 30 seconds, we can use software such as Audacity which is a free and open-source digital audio editor and recording application software available for Windows, macOS, and Linux. Once the software is installed, the following steps can be followed:
Steps to create a tone of 2 kHz:1. Open Audacity.2. Go to the "Generate" menu.3. Select "Tone" from the drop-down menu.4. Set the "Frequency" to 2000 Hz (2 kHz) and "Duration" to 30 seconds.5. Click "OK" to generate the tone.6. Save the tone in a file format that is supported by Audacity (e.g. WAV, MP3, etc.)Steps to mix the tone with the music file:1. Import the music file into Audacity.
2. Go to the "Tracks" menu.3. Select "Add New" from the drop-down menu.4. Select "Mono Track" from the sub-menu.5. A new track will be added to the project.6. Go to the "Generate" menu.7. Select "Tone" from the drop-down menu.8. Set the "Frequency" to 2000 Hz (2 kHz) and "Duration" to 30 seconds.9.
Click "OK" to generate the tone.10. Click and drag the tone from the "Tone" track to the "Mono Track".11. The tone will be mixed with the music file.Notch filter:In order to notch out the tone from the corrupted audio file, we can use a notch filter. The notch filter can be created using the simple pole-zero approach. The following steps can be followed to create the notch filter:1. Open Audacity.2. Import the corrupted audio file.3.
To know more about software visit:
https://brainly.com/question/32393976
#SPJ11
Divide the line segments connecting the points A(2,0) & B(8,4) into 4 equal parts. Find the dividing points nearest to B. a. (7,3) c. (13/2,3) b. (13/2, 7/2) d. (6,3) Divide the line segments connecting the points A(2,0) & B(8,4) into 4 equal parts. Find the dividing points nearest to B. a. (7,3) c. (13/2,3) b. (13/2, 7/2) d. (6,3)
The dividing points nearest to B when dividing the line segment connecting points A(2,0) and B(8,4) into 4 equal parts are **c. (13/2, 3)** and **d. (6, 3)**.
To divide the line segment into 4 equal parts, we need to find the coordinates of the dividing points that are one-fourth and three-fourths of the distance from point A to point B.
First, we calculate the distance between points A and B using the distance formula:
Distance AB = sqrt((8-2)^2 + (4-0)^2) = sqrt(36 + 16) = sqrt(52) = 2*sqrt(13)
Next, we find the coordinates of the dividing point one-fourth of the distance from A to B. We can use the concept of interpolation:
Dividing Point 1 = (1/4) * (B - A) + A
Dividing Point 1 = (1/4) * ((8-2), (4-0)) + (2, 0)
Dividing Point 1 = (6/4, 4/4) + (2, 0)
Dividing Point 1 = (3/2, 1) + (2, 0)
Dividing Point 1 = (3/2 + 2, 1 + 0)
Dividing Point 1 = (7/2, 1)
Similarly, we find the coordinates of the dividing point three-fourths of the distance from A to B:
Dividing Point 2 = (3/4) * (B - A) + A
Dividing Point 2 = (3/4) * ((8-2), (4-0)) + (2, 0)
Dividing Point 2 = (18/4, 12/4) + (2, 0)
Dividing Point 2 = (9/2, 3) + (2, 0)
Dividing Point 2 = (9/2 + 2, 3 + 0)
Dividing Point 2 = (13/2, 3)
Therefore, the dividing points nearest to B are (13/2, 3) and (6, 3), which correspond to options **c. (13/2, 3)** and **d. (6, 3)**.
Learn more about line segment here
https://brainly.com/question/30327422
#SPJ11
A hard disk has the following characteristics: - 2 surfaces - 1024 tracks per surface - 512 sectors per track - 1024 bytes per sector - Track to track seek time of 10 ms - Rotational speed of 8500rpm Calculate i. The total capacity of a hard disk, ii. The average rotational latency, and iii. The time required to read a file of size 4M
The given characteristics of the hard disk are:2 surfaces1024 tracks per surface512 sectors per track1024 bytes per sector Track to track seek time of 10 ms Rotational speed of 8500rpm.i.
The total capacity of a hard disk: Capacity of a hard disk = Number of surfaces × Number of tracks per surface × Number of sectors per track × Number of bytes per sector Capacity = 2 × 1024 × 512 × 1024Capacity = 2,199,023,872 bytes or approximately 2.2 GBii. The average rotational latency: The time required for the disk to rotate 360 degrees is:1 revolution = 60 seconds/8500 rpm = 7.06 msL atency is the time required for the disk to spin one-half revolution.
Thus: Average rotational latency = 1/2 × 7.06 ms = 3.53 msiii. The time required to read a file of size 4M:Given, the size of the file = 4 M = 4 × 1024 × 1024 = 4194304 bytes Number of sectors required to store 4194304 bytes = 4194304 bytes / 1024 bytes per sector = 4096 sectors
To know more about characteristics visit:-
https://brainly.com/question/16965023
#SPJ11
Complete the following code to count the number of ones in
the
Al register value
MOV BL, O ;Reset the counter
MOV CX,————
L2: ROL AL,————
J ————- L2
————
L1: LOOP L2
In the given code, we have to count the number of ones in the Al register value.
Initially, we are setting the value of BL register to 0 which is used to store the count of ones. The CX register is set to 8 as the loop will run for 8 bits. The L2 label marks the start of the loop. Then, in every iteration, the ROL AL, 1 instruction rotates the bits of the AL register one bit to the left.
The NC flag in the JNC instruction checks the carry flag which is set to 1 if the bit shifted out is 1. If the carry flag is not set, it means that the bit shifted out was 0 and we jump to the L1 label. If the carry flag is set, it means that the bit shifted out was 1 and we increment the value of BL by 1. After that, we continue to the L1 label.
To know more about code visit:-
https://brainly.com/question/31138203
#SPJ11
