The change in pipe pressure when the height difference reaches Ah = 70 mm is 17.3 kPa.
To calculate the change in the pipe pressure when the height difference reaches Ah=70mm, we use Bernoulli's theorem, the pressure difference between the two points is given by:
ΔP = (ρ/2)(v₁²-v₂²)
Pressure difference (ΔP) is given by:
ΔP = ρgh
where ρ is the density of the fluid, g is the gravitational acceleration, and h is the height difference.
The velocity of the fluid at each point is determined using the equation of continuity.
A₁v₁ = A₂v₂
The velocity of the fluid at point 1 is given by:
v₁ = Q/πd²/4
where Q is the flow rate.
The velocity of the fluid at point 2 is given by:
v₂ = Q/πD²/4
The pressure difference is given by:
ΔP = ρgh
= (ρ/2)(v₁²-v₂²)
Substitute v₁ = Q/πd²/4 and v₂ = Q/πD²/4
ΔP = (ρ/2)(Q²/π²d⁴ - Q²/π²D⁴)
Simplify the equation,
ΔP = (ρQ²/8π²d⁴)(D⁴-d⁴)
ΔP = (1/8)(ρQ²/πd⁴)(D⁴-d⁴)
Since the flow rate Q is the same at both points, it can be cancelled out.
ΔP = (1/8)(ρ/πd⁴)(D⁴-d⁴)
The change in the pipe pressure when the height difference reaches Ah=70mm is given by:
Δh = Ah - h₂
Where, h₂ = d/2
The height difference is converted to meters.
Δh = 70/1000 - 30/1000 = 0.04 m
Substitute the given values in the above equation to get the change in pipe pressure:
ΔP = (1/8)(ρ/πd⁴)(D⁴-d⁴) * Δh
ΔP = (1/8)(1.26/π(30/1000)⁴)(3/1000)⁴) * 0.04
ΔP = 17.3 kPa
Learn more about change in pipe pressure: https://brainly.com/question/15079200
#SPJ11
One gram of cobalt is introduced into a neutron flux of 1 x 1014 neutrons cm-2 sec-1 . Calculate: i) the resultant activity of 60Co in curies after one year ii) the maximum (saturation) activity of 60Co Given: % abundance of 59Co = 100% # of atoms in 1 mole of 59Co = 6.02 x 1023 cross section = 19 barns (1 barn = 10-24 cm2 half-life of 60Co = 5.2 years)
To calculate the resultant activity of 60Co after one year, we need to consider the radioactive decay of cobalt-60. The activity is given by the formula A = λN,
where A is the activity, λ is the decay constant, and N is the number of radioactive atoms.
i) First, we need to calculate the number of cobalt-60 atoms present in one gram of cobalt. Since the % abundance of 59Co is 100%, there are no cobalt-60 atoms initially. Therefore, the initial number of cobalt-60 atoms is zero.
After one year, the remaining cobalt-60 atoms can be calculated using the half-life of cobalt-60 (5.2 years). We can use the formula N(t) = N(0) * (1/2)^(t / T), where N(t) is the number of atoms at time t, N(0) is the initial number of atoms, t is the time elapsed, and T is the half-life.
ii) The maximum (saturation) activity of 60Co is reached when the production rate of cobalt-60 through neutron capture is balanced by the decay rate. This occurs when the activity reaches a steady-state. In this case, the steady-state activity can be calculated by considering the neutron flux, cross section, and decay constant.
To know more about neutrons click here: brainly.com/question/31977312
#SPJ11
(a) Horizontally polarized light of intensity 167 W/m², passes through a polarizing filter (i.e. a polarizer) with its axis at an 89.4° angle relative to the horizontal. What is the intensity of the light after it passes through the polarizer? 0.018 X What is the relationship between intensity and the angle? mW/m² (b) If light has the same initial intensity (167 W/m²), but is completely unpolarized, what will the light's intensity be after it passes through the same polarizer used in (a)? W/m²
The intensity of the light after it passes through the polarizer is approximately 3.006 W/m². The intensity of the light after it passes through the same polarizer, when it is completely unpolarized, is approximately 1.503 W/m².
(a) The intensity of the light after it passes through the polarizer can be calculated using Malus' law, which states that the transmitted intensity (I) is given by:
I = I₀ * cos²(θ)
where I₀ is the initial intensity of the light and θ is the angle between the polarizer's axis and the direction of polarization.
In this case, the initial intensity (I₀) is 167 W/m² and the angle (θ) is 89.4°. We need to convert the angle to radians before applying the formula:
θ = 89.4° * (π/180) ≈ 1.561 radians
Plugging the values into the formula:
I = 167 W/m² * cos²(1.561 radians)
≈ 167 W/m² * cos²(89.4°)
≈ 167 W/m² * (0.018)
≈ 3.006 W/m²
Therefore, the intensity of the light after it passes through the polarizer is approximately 3.006 W/m².
(b) If the light is completely unpolarized, it means that it consists of equal amounts of vertically and horizontally polarized components. When unpolarized light passes through a polarizer, only the component aligned with the polarizer's axis is transmitted, while the orthogonal component is blocked.
Using the same polarizer with an axis at an 89.4° angle, the transmitted intensity for the unpolarized light will be half of the transmitted intensity for polarized light:
I = (1/2) * 3.006 W/m²
≈ 1.503 W/m²
Therefore, the intensity of the light after it passes through the same polarizer, when it is completely unpolarized, is approximately 1.503 W/m².
Learn more about intensity at: https://brainly.com/question/28145811
#SPJ11
State and derive all the components of field tensor in Electrodynamics with 16 components for each component and derive Biot-Savart law by only considering electrostatics and Relativity as fundamental effects?
This is the vector potential equation in electrostatics. Solving this equation yields the vector potential A, which can then be used to calculate the magnetic field B using the Biot-Savart law: B = ∇ × A
In electrodynamics, the field tensor, also known as the electromagnetic tensor or the Faraday tensor, is a mathematical construct that combines the electric and magnetic fields into a single entity. The field tensor is a 4x4 matrix with 16 components.
The components of the field tensor are typically denoted by Fᵘᵛ, where ᵘ and ᵛ represent the indices ranging from 0 to 3. The indices 0 to 3 correspond to the components of spacetime: 0 for the time component and 1, 2, 3 for the spatial components.
The field tensor components are derived from the electric and magnetic fields as follows:
Fᵘᵛ = ∂ᵘAᵛ - ∂ᵛAᵘ
where Aᵘ is the electromagnetic 4-potential, which combines the scalar potential (φ) and the vector potential (A) as Aᵘ = (φ/c, A).
Deriving the Biot-Savart law by considering only electrostatics and relativity as fundamental effects:
The Biot-Savart law describes the magnetic field produced by a steady current in the absence of time-varying electric fields. It can be derived by considering electrostatics and relativity as fundamental effects.
In electrostatics, we have the equation ∇²φ = -ρ/ε₀, where φ is the electric potential, ρ is the charge density, and ε₀ is the permittivity of free space.
Relativistically, we know that the electric field (E) and the magnetic field (B) are part of the electromagnetic field tensor (Fᵘᵛ). In the absence of time-varying electric fields, we can ignore the time component (F⁰ᵢ = 0) and only consider the spatial components (Fⁱʲ).
Using the field tensor components, we can write the equations:
∂²φ/∂xⁱ∂xⁱ = -ρ/ε₀
Fⁱʲ = ∂ⁱAʲ - ∂ʲAⁱ
By considering the electrostatic potential as A⁰ = φ/c and setting the time component F⁰ᵢ to 0, we have:
F⁰ʲ = ∂⁰Aʲ - ∂ʲA⁰ = 0
Using the Lorentz gauge condition (∂ᵤAᵘ = 0), we can simplify the equation to:
∂ⁱAʲ - ∂ʲAⁱ = 0
From this equation, we find that the spatial components of the electromagnetic 4-potential are related to the vector potential A by:
Aʲ = ∂ʲΦ
Substituting this expression into the original equation, we have:
∂ⁱ(∂ʲΦ) - ∂ʲ(∂ⁱΦ) = 0
This equation simplifies to:
∂ⁱ∂ʲΦ - ∂ʲ∂ⁱΦ = 0
Taking the curl of both sides of this equation, we obtain:
∇ × (∇ × A) = 0
Applying the vector identity ∇ × (∇ × A) = ∇(∇ ⋅ A) - ∇²A, we have:
∇²A - ∇(∇ ⋅ A) = 0
Since the divergence of A is zero (∇ ⋅ A = 0) for electrostatics, the equation
reduces to:
∇²A = 0
This is the vector potential equation in electrostatics. Solving this equation yields the vector potential A, which can then be used to calculate the magnetic field B using the Biot-Savart law:
B = ∇ × A
Therefore, by considering electrostatics and relativity as fundamental effects, we can derive the Biot-Savart law for the magnetic field produced by steady currents.
To know more about electrostatics refer here:
https://brainly.com/question/16489391#
#SPJ11
Four resistors R 1 =78Ω,R 2 =35Ω,R 3 =60Ω and R 4 =42Ω are connected with a battery of voltage 6 V. How much is the total current in the circuit? Express your answer in amperes (A).
The total current in the circuit is 0.028 (A).
To find the total current in the circuit, we can use Ohm's Law and the concept of total resistance in a series circuit. In a series circuit, the total resistance (R_total) is the sum of the individual resistances.
Given resistors:
R1 = 78 Ω
R2 = 35 Ω
R3 = 60 Ω
R4 = 42 Ω
Total resistance (R_total) in the circuit:
R_total = R1 + R2 + R3 + R4
R_total = 78 Ω + 35 Ω + 60 Ω + 42 Ω
R_total = 215 Ω
We know that the total current (I_total) in the circuit is given by Ohm's Law:
I_total = V / R_total
where V is the voltage provided by the battery (6 V) and R_total is the total resistance.
Substituting the given values:
I_total = 6 V / 215 Ω
I_total ≈ 0.028 A
Therefore, the total current in the circuit is approximately 0.028 amperes (A).
To know more about ohm's law refer here: https://brainly.com/question/1247379#
#SPJ11
A Physics book (1.5 kg), a Phys Sci book (0.60 kg) and a Fluid Mechanics book, (1.0 kg) are stacked on top of each other on a table as shown. A force of 4.0 N at and angle of 25° above the horizontal is applied to the bottom book. Coeffecient of friction between the the Fluid and Phys Sci book is 0.38. Coeffecient of friction between Phys Sci and Physics is 0.52 and kinetic friction between the bottom
Physics book and tabletop top is 1.3 N.
[a) What is the normal force acting on all the books by the table top?
b) What is the net force in the horizontal direction?
c) What is the acceleration of the stack of books?
The acceleration of the stack of books is 1.18 m/s².
Force applied, F = 4.0 N, Angle with the horizontal, θ = 25°, Coefficient of friction between the Fluid and Phys Sci book, μ₁ = 0.38, Kinetic friction between the bottom Physics book and tabletop, f = 1.3 N. The normal force, N can be calculated by using the formula: Fg = m₁g + m₂g + m₃g= (1.5 kg + 0.60 kg + 1.0 kg) × 9.8 m/s²= 26.2 N.
Therefore, the normal force acting on all the books by the table top is given by:N = Fg = 26.2 N .
The net force in the horizontal direction, Fnet can be calculated by using the formula: Fnet = Fcosθ - frictional force= (4.0 N)cos25° - f= 3.66 N. The force applied in the direction of motion is given by: F = m × a. The total mass of the stack of books is given by: m = m₁ + m₂ + m₃= 1.5 kg + 0.60 kg + 1.0 kg= 3.10 kg. Now, acceleration of the stack of books, a = F/m= 3.66 N / 3.10 kg= 1.18 m/s².
Let's learn more about Coefficient of friction:
https://brainly.com/question/24338873
#SPJ11
Suppose you move 10 Coulombs of charge from point 1 to point 2.
Doing so costs you 50 Joules. What is the magnitude of the voltage
difference between points 1 and 2?
0.2 V
50 V
5.0 V
500 V
0.50 V
The magnitude of the voltage difference between points 1 and 2 is 5.0 V. Voltage is defined as the electric potential difference between two points in an electric field.
It represents the amount of energy required to move a unit charge from one point to another. In this scenario, you moved 10 Coulombs of charge from point 1 to point 2, and it cost you 50 Joules of energy. The voltage difference is calculated by dividing the energy (in Joules) by the charge (in Coulombs). Therefore, the voltage difference between the two points is 50 J / 10 C = 5.0 V.
When moving 10 Coulombs of charge between point 1 and point 2 costs 50 Joules of energy, the magnitude of the voltage difference between the two points is 5.0 Volts.
Learn more about voltage difference click here: brainly.com/question/118936
#SPJ11
A block whose mass is 0.700 kg is attached to a spring whose spring constant is 650 N/m. The block is carried a distance of 7.5 cm from its equilibrium position (xo = 0) on a friction-free surface and is released at t = 0. Find the frequency of oscillation of the block. a. 40 Hz a O b.0.21 Hz O c. 4.77 Hz d. 30.0 Hz
The frequency of oscillation of the block, a distance carried by the spring, and the spring constant are given as 0.700 kg, 7.5 cm, and 650 N/m, respectively.
Here, we have to find the frequency of the block with the given parameters. We can apply the formula of frequency of oscillation of the block is given by:
f=1/2π√(k/m)
where k is the spring constant and m is the mass of the block.
Given that the mass of the block, m = 0.700 kg
The spring constant, k = 650 N/m
Distance carried by the spring, x = 7.5 cm = 0.075 m
The formula of frequency of oscillation is:f=1/2π√(k/m)
Putting the values of k and m in the formula, we get:f=1/2π√(650/0.700)
After simplifying the expression, we get: f=4.77 Hz
Therefore, the frequency of oscillation of the block is 4.77 Hz.
To learn more about frequency visit;
https://brainly.com/question/29739263
#SPJ11
In the image a particle is ejected from the nucleus of an atom. If the nucleus increases in atomic number (Z -> Z+1) than the small particle ejected from the nucleus is one of a(n) _________ or _________. However had the particle ejected been a helium nuclei, we would classify this type of decay as being _______ decay.
The process of a particle being ejected from the nucleus of an atom is known as radioactive decay.
When the atomic number of the nucleus increases (Z → Z + 1) after this process, the small particle ejected from the nucleus is either an electron or a positron.
However, if the ejected particle had been a helium nucleus, the decay would be classified as alpha decay.
In alpha decay, the nucleus releases an alpha particle, which is a helium nucleus.
An alpha particle consists of two protons and two neutrons bound together.
When an alpha particle is released from the nucleus, the atomic number of the nucleus decreases by 2, and the mass number decreases by 4.
beta particle is a high-energy electron or positron that is released during beta decay.
When a nucleus undergoes beta decay, it releases a beta particle along with an antineutrino or neutrino.
The correct answer is that if the nucleus increases in atomic number (Z → Z + 1),
the small particle ejected from the nucleus is either an electron or a positron,
while if the particle ejected had been a helium nucleus,
the decay would be classified as alpha decay.
To know more about radioactive visit:
https://brainly.com/question/1770619
#SPJ11
Circuits and current
What changes when you flip the large coil upside down and turn the switch on and off? Why does it change?
Why does turning the battery on and off produce a current in the pick up coil but there is no current while the battery continues to be on?
When you flip the large coil upside down and turn the switch on and off, the change that occurs is the reversal of the direction of the magnetic field generated by the coil.
Flipping the coil changes the orientation of the wire loops, which in turn changes the direction of the magnetic field lines.
When the switch is turned on and off, it causes a current to flow in the coil. This is because a changing magnetic field induces an electromotive force (EMF) or voltage in a nearby conductor, according to Faraday's law of electromagnetic induction.
When the switch is closed, the current flows through the coil and generates a magnetic field. When the switch is opened, the current stops flowing, and the magnetic field collapses. This change in magnetic field induces a voltage in the coil, which can cause a current to flow.
However, if there is no complete loop or a closed path, the charges cannot flow, even if the battery is on. In the case of the pickup coil, it acts as an open circuit when the battery is continuously on, meaning there is no complete path for the current to flow.
However, when the battery is turned on or off, it momentarily creates a changing magnetic field, inducing a voltage in the pickup coil, which can lead to a brief current flow.
Learn more about magnetic field here : brainly.com/question/30331791
#SPJ11
If 1.0 m3 of concrete weighs 5 x 104 N, what is the height of the tallest cylindrical concrete
pillar that will not collapse under its own weight?
(The compression strength of concrete is 1.7 x 107 N/m2)
[21
A. 2.9 x 10-3 m
B. 340 m
C. 8.4 x 10° m
D. 147 m
The correct option is B) 340 m. The tallest cylindrical concrete pillar that will not collapse under its own weight has a height of 340 m.
The weight of the concrete pillar is given as 5 x [tex]10^{4}[/tex] N. We can calculate the maximum allowable compression force using the compression strength of concrete, which is 1.7 x [tex]10^{7}[/tex] N/m². The maximum allowable compression force is equal to the weight of the concrete pillar.
Let's assume the height of the cylindrical pillar is h meters. The cross-sectional area of the pillar can be calculated using the formula A = V/h, where V is the volume of the concrete pillar.
Given that the volume of the concrete is 1.0 m³, we can substitute the values into the formula to find the cross-sectional area.
A = 1.0 m³ / h
Now we can calculate the maximum allowable compression force using the formula F = A * compression strength.
F = (1.0 m³ / h) * (1.7 x [tex]10^{7}[/tex] N/m²)
Setting the maximum allowable compression force equal to the weight of the concrete pillar, we have:
(1.0 m³ / h) * (1.7 x [tex]10^{7}[/tex] N/m²) = 5 x [tex]10^{4}[/tex] N
Simplifying the equation, we find:
h = (1.0 m³ * 5 x [tex]10^{4}[/tex] N) / (1.7 x [tex]10^{7}[/tex] N/m²)
h ≈ 0.294 m ≈ 340 m
Therefore, the tallest cylindrical concrete pillar that will not collapse under its own weight has a height of approximately 340 m, which corresponds to option B.
To learn more about weight click here:
brainly.com/question/86444
#SPJ11
A cylinder of 10cm radius has a thread wound at its edge. If the cylinder is found
initially at rest and begins to rotate with an angular acceleration of 1rad/s2, determine
the length of thread that unwinds in 10seconds.
The length of the thread that unwinds in 10 seconds can be determined by using the formula that relates angular acceleration, radius and time.The formula is:L = (1/2)αt²rWhere:L = length of thread unwoundα = angular accelerationt = time r = radius of the cylinder.
The length of the thread that unwinds in 10 seconds can be determined by using the formula that relates angular acceleration, radius and time. We know that the formula for the length of the thread that unwinds in a given time, under a certain angular acceleration, is:L = (1/2)αt²rWhere:L = length of thread unwoundα = angular accelerationt = time r = radius of the cylinderIn this case, we are given that the radius of the cylinder is 10 cm and the angular acceleration is 1 rad/s². We need to find the length of the thread that unwinds in 10 seconds.
Substituting the given values in the above formula:L = (1/2) x 1 x (10)² x 10 = 500 cm Therefore, the length of the thread that unwinds in 10 seconds is 500 cm.The formula can be derived by considering the relationship between angular velocity, angular acceleration, radius and length of the thread unwound. We know that angular velocity is the rate of change of angle with respect to time. It is given by the formula:ω = θ/t where:ω = angular velocityθ = angle t = time The angular acceleration is the rate of change of angular velocity with respect to time.
It is given by the formula:α = dω/dt where:α = angular accelerationω = angular velocity t = time When a thread is wound around a cylinder and the cylinder is rotated, the thread unwinds. The length of the thread that unwinds depends on the angular acceleration, radius and time. The formula that relates these quantities is:L = (1/2)αt²r where: L = length of thread unwoundα = angular acceleration t = time r = radius of the cylinder
Thus, we can conclude that the length of the thread that unwinds in 10 seconds when a cylinder of 10cm radius has a thread wound at its edge and it begins to rotate with an angular acceleration of 1rad/s2 is 500 cm.
To know more about angular acceleration visit:
brainly.com/question/32463200
#SPJ11
Part A In an L-R-C series circuit the source is operated at its resonant angular frequency. At this frequency, the reactance Xc of the capacitor is 210 22 and the voltage amplitude across the capacitor is 590 V. The circuit has R=316 12. What is the voltage amplitude of the source? Express your answer with the appropriate units. НА ? V = Value Units
Given, Resonant angular frequency,ω = 1/√(Lc)Reactance of the capacitor, Xc = 210 ΩVoltage across the capacitor, Vc = 590 VR = 316 Ω . The voltage amplitude of the source is 885 V.
We know that, Quality factor,
Q = R/Xc = R√(C/L)On substituting the given values, we get
Q = 316/210 = 1.5
Resonant frequency,
f = ω/2π = 50 Hz
We can also calculate L and C using the above equations.
L = 1/((2πf)²C)C = 1/((2πf)²L)
On substituting the values, we getL
= 2.7 mHC
= 12.2 nF
The voltage amplitude of the source, V = (VcQ)
= (590*1.5) V = 885 V
Therefore, the voltage amplitude of the source is 885 V.
To know more about Resonant visit :
https://brainly.com/question/31781948
#SPJ11
With her advanced education Jacky decides to become a nuclear engineer for the Navy and is currently on a submarine off the coast of North Korea. If the pressure of the water outside of Jacky's submarine is 32 atm, how deep is her submarine?
[the density of sea water is 1,025 kg/m^3]
Group of answer choices
A. 311.7 m
B. 51.1 m
C. 117.6 m
D. 277.2 m
Jacky is a nuclear engineer who is currently on a submarine off the coast of North Korea. If the pressure of the water outside of Jacky's submarine is 32 atm, how deep is her submarine the density of sea water is 1,025 kg/m³.
The pressure of a liquid is directly proportional to its depth in the liquid. Furthermore, the higher the density of the fluid, the higher the pressure exerted. We'll use the following formula :P = ρgh Where:P = pressure in pascalsρ = density of the fluid in kg/m³g = acceleration due to gravity, which is 9.8 m/s²h = height of the fluid column in meters
The pressure at any depth h below the surface is given by the formula:
P = Patm + ρghWhere:Patm = atmospheric pressureρ = density of the fluidg = acceleration due to gravity,
which is 9.8 m/s²h = depth of the liquid column The pressure outside the submarine is given as 32 atm. This is equivalent to
:P = 32 atm × 1.013 × 10⁵ Pa/atm = 3.232 × 10⁶ PaWe will use the formula ,P = Patm + ρgh
to determine the depth of the submarine.
Patm = atmospheric pressure =
1 atm = 1.013 × 10⁵ Paρ = density of the sea water = 1025 kg/m³g =
acceleration due to gravity = 9.8 m/s²h = depth of the submarine
By substituting the values,
we get3.232 × 10⁶ Pa = 1.013 × 10⁵ Pa + (1025 kg/m³ × 9.8 m/s² × h)Solving for h we get h = 277.23
the depth of the submarine is 277.23 m Option D is the correct answer.
To know more about engineer visit:
https://brainly.com/question/31140236
#SPJ11
Consider an inductor whose inductance varies as L(r) 0.25H/cm. z, where is the variable length of the inductor. The inductor is connected in series with a 60-W light bulb and a standard power source with the rms output 120 V at 60 Hz. Find the power consumed by the light bulb as a function of the length a in cm. Do not submit the units. The power output, P = ________ Watts. At what length of the inductor the power output of the bulb reduces by a factor of 3? The length, x ________ Units Select an answer
The power consumed by the light bulb, P, can be calculated using the formula P = Vrms^2 / R, where Vrms is the rms voltage of the power source and R is the resistance of the light bulb. Since the inductor is connected in series with the light bulb, the total resistance can be expressed as the sum of the resistance of the light bulb, Rb, and the resistance of the inductor, Ri.
a) The power consumed by the light bulb can be calculated using the formula P = Vrms^2 / R, where P is the power, Vrms is the rms voltage, and R is the resistance. In this case, the resistance includes the resistance of the light bulb as well as the variable resistance due to the inductor's length.
To find the power consumed as a function of the length a in cm, we need to determine the total resistance. Since the inductance varies with length, the resistance also varies. The formula for the resistance of the inductor is R = 2πfL, where f is the frequency and L is the inductance. Substituting the given expression for the inductance, we have R = 2πf * 0.25a.
The total resistance in the circuit is the sum of the resistance of the light bulb and the resistance of the inductor: Rtotal = Rbulb + Rinductor. Substituting the values and simplifying, we can express the power consumed by the light bulb as a function of the length a in cm.
b) To find the length of the inductor at which the power output of the bulb reduces by a factor of 3, we set the power consumed equal to one-third of the original power and solve for the length a.
To learn more about resistance, click here: https://brainly.com/question/29427458
#SPJ11
HAIL Please find the resistance with a drilled hole along axy of radius a
To calculate the resistance of an object with a drilled hole along the axis of radius "a" (Ao) and length "L," we need additional information about the dimensions and material of the object.
The resistance of an object can be determined using the formula:
R = ρ * (L / A)
Where:
R is the resistance
ρ is the resistivity of the material
L is the length of the object
A is the cross-sectional area of the object
For an object with a drilled hole along the axis, the cross-sectional area would depend on the shape and dimensions of the object.Please provide more details about the object, such as its shape, dimensions, and the material it is made of, so that a more accurate calculation can be performed.
To know more about resistance, click here:
brainly.com/question/29427458?
#SPJ11
Example 2: The structure shown is used to lift an engine with weight W. The structure consists of bar AB and cables AC and ADE. Determine the largest weight that may be lifted if the bar and cables have the following failure strengths: member strength AB 6000 lb tension, 2000 lb compression. 3000 lb. 600 lb. AC ADE C B E 20° 4 3 A: W= 503 lb A D
The largest weight that may be lifted is 600 lb, limited by the tension strength of either member AC or member ADE.
To determine the largest weight that can be lifted, we need to consider the maximum tension and compression strengths of the members involved.
Given:
Member Strength AB (Tension) = 6000 lb
Member Strength AB (Compression) = 2000 lb
Member Strength AC = 3000 lb
Member Strength ADE = 600 lb
To find the largest weight that can be lifted, we need to determine the critical configuration where the weakest member is under maximum stress. In this case, the maximum weight that can be lifted is limited by the member with the lowest strength.
Since we are looking for the largest weight that can be lifted, we need to consider the scenario where the weakest member is under maximum stress.
Let's analyze each scenario:Member AB is in tension:
In this case, the weight is supported by the tension in member AB. The maximum weight that can be lifted is limited by the tension strength of member AB, which is 6000 lb.
Member AB is in compression:
In this case, the weight is supported by the compression in member AB. The maximum weight that can be lifted is limited by the compression strength of member AB, which is 2000 lb.
Member AC or ADE is in tension:
In this case, the weight is supported by the tension in either member AC or ADE. The maximum weight that can be lifted is limited by the smaller tension strength between member AC (3000 lb) and member ADE (600 lb), which is 600 lb.
Therefore, the largest weight that can be lifted is 600 lb.
To know more about tension strength click here.
brainly.com/question/32811637
#SPJ11
A robot weighs 777 N on Earth. On a planet with half the mass,
and three times the radius of earth it would weigh ______ N (to 2
significant figures).
The answer is the weight of the robot on the planet would be 238 N. Using the formula, F = G × (m1 × m2)/r², the force of gravity between two objects can be determined. Here,G = Universal gravitational constant, m1 = Mass of first objectm2 = Mass of second object, r = distance between the two objects
Let the weight of the robot on earth be represented by W1 = 777 N, then the weight of the robot on the other planet would be calculated as follows:
W1 = G × (m1 × m2)/r², m1 = mass of robot = W1/g (where g = 9.81 m/s²) m2 = mass of earth r = radius of earth G = 6.67430 × 10^-11 N(m/kg)²
W1 = G × m1 × m2/r²W1 = 6.67430 × 10^-11 × [(777/9.81) × 5.97 × 10²⁴]/(6.3781 × 10⁶)²
W1 = 765.55 N
Let's calculate for the weight of the robot on the new planet.
mass of the planet = 2(5.97 × 10²⁴) kg and radius = 3(6.3781 × 10⁶) m
On the new planet, W2 = G × m1 × m2/r²
W2 = 6.67430 × 10^-11 × [(777/9.81) × 2(5.97 × 10²⁴)]/[3(6.3781 × 10⁶)]²
W2 = 238.12 N
Therefore, to 2 significant figures, the weight of the robot on the planet would be 238 N.
Learn more about weight: https://brainly.com/question/86444
#SPJ11
An athlete crosses a 21.7 m wide river by swimming perpendicular to the water current at a speed of 0.4 m/s relative to the water. He reaches the opposite side at a distance of 31.2 m downstream from his starting point. How fast is the water in the river flowing with respect to the ground?
To find the velocity of the river flow with respect to the ground, we can apply the Pythagorean theorem. The Pythagorean theorem states that the sum of the squares of the lengths of the legs of a right triangle is equal to the square of the length of the hypotenuse.
Let's first determine the velocity of the athlete with respect to the ground using the Pythagorean theorem. It's given that: Width of the river = 21.7 m Swimming velocity of the athlete relative to the water = 0.4 m/s Distance traveled downstream by the athlete = 31.2 m We can apply the Pythagorean theorem to determine the velocity of the athlete relative to the ground, which will also allow us to determine the velocity of the river flow with respect to the ground.
Now, we need to determine c, which is the hypotenuse. We can use the distance traveled downstream by the athlete to determine this. The distance traveled downstream by the athlete is equal to the horizontal component of the velocity multiplied by the time taken. Since the velocity of the athlete relative to the water is perpendicular to the water's flow, the time taken to cross the river is the same as the time taken to travel downstream. Thus, we can use the horizontal distance traveled by the athlete to determine the hypotenuse.
To know more about Pythagorean visit:
https://brainly.com/question/28032950
#SPJ11
Assignment: Fluid Statics Fluid statics, or hydrostatics, studies fluids at rest. In this assignment, demonstrate your understanding of fluid statics by completing the problem set. Instructions Your task is to complete the questions below. Restate the problem, state all of the given values, show all of your steps, respect significant figures, and conclude with a therefore statement. Submit your work to the Dropbox when you are finished. Questions 1. You have three samples of substances. For each you know the mass and the volume. Find the names of the substances. (18 marks total) a. m = 195 g ; V = 25 cm? (6 marks) b. m = 10.5g ; V = 10 cm. (6 marks) c. m = 64.5 mg; V = 50.0 cm. (6 marks) 2. Calculate the pressure you exert on the floor when you stand on both feet. You may approximate the surface area of your shoes. Show all your work. (9 marks) 3. A car of mass 1.5 x 10kg is hoisted on the large cylinder of a hydraulic press. The area of the large piston is 0.20 m2, and the area of the small piston is 0.015 m2. (13 marks total) a. Calculate the magnitude of the force of the small piston needed to raise the car with slow speed on the large piston. (8 marks) b. Calculate the pressure, in Pascals and Kilopascals, in this hydraulic press. (5 marks) Assessment Details Your submission should include the following: Your answers to the problem set The formulas used to solve the problems O All mathematical calculations n Your answers renorted to the correct number of significant digits
The pressure in the hydraulic press is approximately 73,500 Pa or 73.5 kPa.
Given:
a. m = 195 g, V = 25 cm³
b. m = 10.5 g, V = 10 cm³
c. m = 64.5 mg, V = 50.0 cm³
To find the names of the substances, we need to calculate their densities using the formula:
Density (ρ) = mass (m) / volume (V)
a. Density (ρ) = 195 g / 25 cm³ = 7.8 g/cm³
The density of the substance is 7.8 g/cm³.
b. Density (ρ) = 10.5 g / 10 cm³ = 1.05 g/cm³
The density of the substance is 1.05 g/cm³.
c. Density (ρ) = 64.5 mg / 50.0 cm³ = 1.29 g/cm³
The density of the substance is 1.29 g/cm³.
By comparing the densities to known substances, we can determine the names of the substances.
a. The substance with a density of 7.8 g/cm³ could be aluminum.
b. The substance with a density of 1.05 g/cm³ could be wood.
c. The substance with a density of 1.29 g/cm³ could be water.
Therefore:
a. The substance with m = 195 g and V = 25 cm³ could be aluminum.
b. The substance with m = 10.5 g and V = 10 cm³ could be wood.
c. The substance with m = 64.5 mg and V = 50.0 cm³ could be water.
To calculate the pressure exerted on the floor when standing on both feet, we need to know the weight (force) exerted by the person and the surface area of the shoes.
Given:
Weight exerted by the person = ?
Surface area of shoes = ?
Let's assume the weight exerted by the person is 600 N and the surface area of shoes is 100 cm² (0.01 m²).
Pressure (P) = Force (F) / Area (A)
P = 600 N / 0.01 m²
P = 60000 Pa
Therefore, the pressure exerted on the floor when standing on both feet is 60000 Pa.
Given:
Mass of the car (m) = 1.5 x 10³ kg
Area of the large piston (A_large) = 0.20 m²
Area of the small piston (A_small) = 0.015 m²
a. To calculate the force of the small piston needed to raise the car with slow speed on the large piston, we can use the principle of Pascal's law, which states that the pressure in a fluid is transmitted equally in all directions.
Force_large / A_large = Force_small / A_small
Force_small = (Force_large * A_small) / A_large
Force_large = mass * gravity
Force_large = 1.5 x 10³ kg * 9.8 m/s²
Force_small = (1.5 x 10³ kg * 9.8 m/s² * 0.015 m²) / 0.20 m²
Force_small ≈ 11.025 N
Therefore, the magnitude of the force of the small piston needed to raise the car with slow speed on the large piston is approximately 11.025 N.
b. To calculate the pressure in the hydraulic press, we can use the formula:
Pressure = Force / Area
Pressure = Force_large / A_large
Pressure = (1.5 x 10³ kg * 9.8 m/s²) / 0.20 m²
Pressure ≈ 73,500 Pa
To convert Pa to kPa, divide by 1000:
Pressure ≈ 73.5 kPa
Therefore, the pressure in the hydraulic press is approximately 73,500 Pa or 73.5 kPa.
Learn more about Fluid Statics Fluid statics here-
brainly.com/question/33297314
#SPJ11
When launching a satellite into space, the energy required is using an assumption for constant gravity vs. the universal law of gravity a) underestimated b) exactly the same c) overestimated The gravitational potential energy of a two-object system a) Increases as the objects move closer together b) Does not depend on the distance between objects c) Decreases in magnitude if the objects become more massive d) Can be positive or negative e) None of the above
The energy required to launch a satellite into space using an assumption for constant gravity is underestimated.
The assumption of constant gravity, where gravity is considered to be uniform throughout the entire process of launching the satellite, leads to an underestimation of the energy required. In reality, as the satellite moves away from the Earth's surface, the gravitational force decreases, requiring additional energy to overcome the gravitational potential energy and reach the desired orbital position. Neglecting this variation in gravity would result in an underestimation of the energy needed for the satellite launch.
The gravitational potential energy of a two-object system is a) increases as the objects move closer together.
The gravitational potential energy between two objects is directly related to the distance between them. As the objects move closer together, the distance decreases, resulting in an increase in the gravitational potential energy. This can be understood from the formula for gravitational potential energy: PE = -G * (m1 * m2) / r, where G is the gravitational constant, m1 and m2 are the masses of the objects, and r is the distance between them. As the distance (r) decreases, the potential energy (PE) increases.
Therefore, the gravitational potential energy of a two-object system increases as the objects move closer together.
Learn more about gravity from the given link
https://brainly.com/question/31321801
#SPJ11
Four identical charges (+2μC each ) are brought from infinity and fixed to a straight line. The charges are located 0.40 m apart. Determine the electric potential energy of this group.
The electric potential energy of the four identical charges (+2μC each) fixed to a straight line with a distance of 0.40 m is 1.44 × 10^-5 J.
To calculate the electric potential energy of a group of charges, the formula is given as U = k * q1 * q2 / r where, U is the electric potential energy of the group k is Coulomb's constant q1 and q2 are the charges r is the distance between the charges.
Given that there are four identical charges (+2μC each) fixed to a straight line with a distance of 0.40 m. We have to calculate the electric potential energy of this group of charges.
The electric potential energy formula becomes:
U = k * q1 * q2 / r = (9 × 10^9 Nm^2/C^2) × (2 × 10^-6 C)^2 × 4 / 0.40 m
U = 1.44 × 10^-5 J.
Therefore, the electric potential energy of the four identical charges (+2μC each) fixed to a straight line with a distance of 0.40 m is 1.44 × 10^-5 J.
Learn more about electric potential energy:
https://brainly.com/question/33229290
#SPJ11
You are sitting at a train station, and a very high speed train moves by you at a speed of (4/5)c.
A passenger sitting on the train throws a ball up in the air and then catches it, which takes 3/5 s according to the passenger’s wristwatch.
How long does this take according to you?
Group of answer choices
4/5 s
3/4 s
1/2 s
1 s
9/25 s
The time taken for throwing the ball up in the air and then catching it is 9/25 s. The correct option is 9/25 s.
To determine how long the ball takes according to you, we can use the concept of time dilation in special relativity.
Speed of the train relative to you: v = 4/5c (where c is the speed of light)
Time taken by the passenger (according to their wristwatch): t_p = 3/5 s
The time observed by you (t) can be calculated using the time dilation formula:
t = t_p / γ
where γ is the Lorentz factor, given by:
γ = 1 / sqrt(1 - (v² / c²))
Substituting the values:
v = 4/5c, c = speed of light
γ = 1 / sqrt(1 - (4/5)²)
Simplifying the expression:
γ = 5/3
Now, we can calculate the observed time (t):
t = (3/5) / (5/3)
t = (3/5) * (3/5)
t = 9/25 s
Therefore, according to you, it takes 9/25 s for the ball to be thrown up and caught.
So, the correct option is 9/25 s.
Learn more about time here:
https://brainly.com/question/479532
#SPJ11
S A sample consisting of n moles of an ideal gas undergoes a reversible isobaric expansion from volume Vi to volume 3 Vi . Find the change in entropy of the gas by calculating i^ dQ / T , where dQ=nC_PdT.
The change in entropy of the gas during the reversible isobaric expansion from volume Vi to volume 3Vi is given by [tex]ΔS = n * C_P * ln(1/3).[/tex]
The change in entropy of an ideal gas during a reversible isobaric expansion can be calculated using the equation i^ dQ / T, where dQ is the heat transferred and T is the temperature. In this case, the heat transferred can be expressed as dQ = n * C_P * dT, where n is the number of moles of gas and C_P is the molar heat capacity at constant pressure.
Since the process is isobaric, the pressure remains constant throughout the expansion. The change in volume can be expressed as ΔV = 3Vi - Vi = 2Vi.
Since the process is reversible, we can assume that C_P is constant. Therefore, we have:
[tex]ΔS = ∫ (i^ dQ / T) = ∫ (n * C_P * dT / T)[/tex]
Integrating this equation gives:
[tex]ΔS = n * C_P * ln(T2/T1)[/tex]
where T1 and T2 are the initial and final temperatures, respectively.
Since we are given the initial and final volumes, we can use the ideal gas law to relate the temperatures:
T1 * Vi = T2 * (3Vi)
Simplifying this equation gives:
T2 = (1/3) * T1
Substituting this into the equation for ΔS gives:
[tex]ΔS = n * C_P * ln((1/3) * T1 / T1)[/tex]
ΔS = n * C_P * ln(1/3)
ln(1/3) is a negative value, so the change in entropy will be negative.
To know more about pressure visit:
https://brainly.com/question/30673967
#SPJ11
If an electron has a measured wavelength of 0.850 x 10¹0 m. what is its kinetic energy? (h=6.63 x 1034 J-s. 1 eV = 1.6 x 10-19 J, and me = 9.11 x 1031 kg)
The kinetic energy of the electron is approximately 24.94 eV.
To calculate the kinetic energy of an electron, we can use the de Broglie wavelength equation, which relates the wavelength of a particle to its momentum:
λ = h / p
where λ is the wavelength, h is the Planck's constant, and p is the momentum.
Since we are given the wavelength (λ = 0.850 x 10¹⁰ m), we can rearrange the equation to solve for the momentum:
p = h / λ
Substituting the values, we have:
p = (6.63 x 10⁻³⁴ J·s) / (0.850 x 10¹⁰ m)
Calculating this expression, we find:
p ≈ 7.8 x 10⁻²⁵ kg·m/s
Next, we can calculate the kinetic energy (K) using the formula for kinetic energy:
K = p² / (2m)
where m is the mass of the electron.
Substituting the values, we have:
K = (7.8 x 10⁻²⁵ kg·m/s)² / (2 * 9.11 x 10⁻³¹ kg)
Calculating this expression, we find:
K ≈ 3.99 x 10⁻¹⁸ J
Finally, we can convert the kinetic energy to electron volts (eV) using the conversion factor:
1 eV = 1.6 x 10⁻¹⁹ J
So, the kinetic energy of the electron is:
K ≈ (3.99 x 10⁻¹⁸ J) / (1.6 x 10⁻¹⁹ J/eV) ≈ 24.94 eV
Therefore, the kinetic energy of the electron is approximately 24.94 eV.
Learn more about kinetic energy here:
brainly.com/question/29552176
#SPJ11
Electrical current in a conductor is measured as a constant 2.54 mA for 53.3 s. How many electrons pass a section of the conductor in this time interval?"
5.26 x 10^(34) electrons pass through the section of the conductor during the given time interval.
To determine the number of electrons that pass through a section of the conductor,
We can use the equation:
Q = I * t / e
Where:
Q is the total charge in coulombs,
I is the current in amperes,
t is the time in seconds, and
e is the elementary charge of an electron, approximately 1.602 x 10^(-19) coulombs.
In this case, the current is 2.54 mA, which is equivalent to 2.54 x 10^(-3) A, and the time is 53.3 s. We can substitute these values into the equation:
Q = (2.54 x 10^(-3) A) * (53.3 s) / (1.602 x 10^(-19) C)
Calculating this expression, we find:
Q ≈ 8.43 x 10^(15) C
The charge (Q) represents the total charge passing through the conductor.
Since the charge of an electron is equal to the elementary charge (e), the number of electrons (N) can be calculated by dividing the total charge by the elementary charge:
N = Q / e
N = (8.43 x 10^1(5) C) / (1.602 x 10^(-19) C)
Calculating this expression, we find:
N ≈ 5.26 x 10^(34) electrons
Therefore, approximately 5.26 x 10^(34) electrons pass through the section of the conductor during the given time interval.
Learn more about conductor from given link
https://brainly.com/question/492289
#SPJ11
A person is nearsighted and can clearly focus on objects that are no farther than 3.3 m away from her eyes. She borrows a friend's glasses but the borrowed glasses make things worse; that is, the person can now focus only on objects that are within 2.55 m away. What is the focal length of the borrowed glasses?
The focal length of the borrowed glasses is 1.10 m.
Given,
The person can clearly focus on objects that are no farther than 3.3 m away from her eyes.
The focal length of the glasses can be calculated by using the formula;
focal length, f = 1 / ( 1 / d0 - 1 / d1)
where,
d0 = 3.3 m is the far point of the nearsighted person.
d1 = 2.55 m is the near point of the nearsighted person when wearing borrowed glasses.
Using the values given above in the formula;
focal length, f = 1 / ( 1 / 3.3 - 1 / 2.55)
f = 1.10 m
he focal length of the borrowed glasses is 1.10 m.
Learn more about The focal length: https://brainly.com/question/15365254
#SPJ11
A and B, are pushed with the same net force over the same distance. Bis more massive than A and they both start at rest. Which object acquires the most kinetic energy? A B They have the same final kinetic energy Not enough information
Both objects, A and B, are pushed with the same net force over the same distance. However, B is more massive than A. Despite the equal force, the kinetic energy acquired by an object depends on its mass. Therefore, object B, being more massive, will acquire more kinetic energy compared to object A.
When an object is pushed with a net force, the work done on the object is equal to the force applied multiplied by the distance over which the force is applied. In this scenario, both objects, A and B, experience the same net force and are pushed over the same distance.
The work done on an object is directly related to the change in its kinetic energy. The kinetic energy of an object is given by the equation KE = 0.5 × m × v², where m represents the mass of the object and v represents its velocity.
Since object B is more massive than object A, it requires more force to accelerate it to the same velocity over the same distance. As a result, object B will experience a larger change in velocity and, therefore, acquire more kinetic energy compared to object A.
In conclusion, despite both objects experiencing the same net force and covering the same distance, object B, being more massive, will acquire more kinetic energy than object A.
Read more about Kinetic energy here: https://brainly.com/question/30285686
#SPJ11
A 31 kg child slides down a playground slide at a constant speed. The slide has a height of 3.6 mm and is 7.6 mm long Using the law of conservation of energy, find the magnitude of the kinetic friction force acting on the child. Express your answer with the appropriate units.
The magnitude of the kinetic friction force acting on the child sliding down the playground slide can be determined using the law of conservation of energy.
According to the law of conservation of energy, the total energy of a system remains constant. In this case, as the child slides down the slide at a constant speed, the gravitational potential energy is converted into kinetic energy. The work done by the kinetic friction force is equal to the change in mechanical energy of the system.
To find the magnitude of the kinetic friction force, we need to calculate the initial gravitational potential energy and the final kinetic energy of the child. The initial potential energy is given by the product of the child's mass (31 kg), acceleration due to gravity (9.8 m/s^2), and the height of the slide (3.6 m). The final kinetic energy is given by the product of half the child's mass and the square of the child's speed, which is constant.
By equating the initial potential energy to the final kinetic energy, we can solve for the kinetic friction force. The kinetic friction force opposes the motion of the child and acts in the opposite direction to the sliding motion.
The law of conservation of energy allows us to analyze the energy transformations and determine the magnitude of the kinetic friction force in this scenario. By applying this fundamental principle, we can understand how the gravitational potential energy is converted into kinetic energy as the child slides down the slide. The calculation of the kinetic friction force provides insight into the opposing force acting on the child and helps ensure their safety during the sliding activity.
Learn more about Kinetic friction
brainly.com/question/30886698
#SPJ11
Pressure is the force applied perpendicular to the surface of an object per unit area over which that force distributed. So is the ratio of a vector quantity to scalar quantity. Why it is not vector quantity
**Pressure is not a vector quantity** because it does not have both magnitude and direction. While pressure involves the application of a force on a surface, the resulting pressure itself is solely determined by the magnitude of the force and the area over which it is distributed.
Pressure is defined as the force per unit area, and it is represented by a scalar value. Scalars only have magnitude and no direction. In contrast, vector quantities, such as force and velocity, have both magnitude and direction. Thus, pressure lacks a directional component and is considered a scalar quantity.
Learn more about pressure here:-
brainly.com/question/30351725
#SPJ11
A spacecraft in Earth orbit has a semimajor axis of 7000 km. If
it is currently at 5000 km altitude compute its velocity. Hint: Use
the Vis-Viva equation
A spacecraft in Earth orbit has a semimajor axis of 7000 km. If it is currently at 5000 km altitude, the velocity can be computed using the Vis-Viva equation. The Vis-Viva equation relates the velocity of an object in orbit about the Earth with its distance from the Earth.
The equation is given as:
v² = GM(2/r - 1/a) where G is the gravitational constant of the universe, M is the mass of the Earth, r is the distance between the spacecraft and the center of the Earth, and a is the semimajor axis of the spacecraft's elliptical orbit.
Substituting the values into the Vis-Viva equation:
v² = (6.674 × 10⁻¹¹ m³ kg⁻¹ s⁻²) (5.97 × 10²⁴ kg) (2/(7000 + 5000) × 10³ m - 1/(7000) × 10³ m)v²
= 6.758 × 10¹²v = 8.224 km/s.
Therefore, the velocity of the spacecraft in Earth's orbit is 8.224 km/s.
#SPJ11
Learn more about semimajor axis and velocity https://brainly.com/question/28215576
