Answer:
Explanation:
To determine the ratio p₁/P2 of the densities of the liquids, we can use Bernoulli's equation, which relates the pressure, velocity, and height of a fluid. According to Bernoulli's equation, the pressure at two different points in a fluid can be related as follows:
P₁ + 1/2ρ₁v₁² + ρ₁gh₁ = P₂ + 1/2ρ₂v₂² + ρ₂gh₂
Where:
P₁ and P₂ are the pressures at points 1 and 2 respectively,
ρ₁ and ρ₂ are the densities of the liquids in tanks 1 and 2 respectively,
v₁ and v₂ are the velocities of the liquids at the respective holes,
g is the acceleration due to gravity, and
h₁ and h₂ are the depths of the holes below the liquid surface.
Since the mass flow rate is the same for the two holes, we can equate the mass flow rates:
ρ₁Av₁ = ρ₂Av₂
Where A₁ and A₂ are the cross-sectional areas of the holes in tanks 1 and 2 respectively.
Given that the hole in tank 1 has half the cross-sectional area of the hole in tank 2 (A₁ = 1/2A₂), and it is at twice the depth below the surface (h₁ = 2h₂), we can substitute these values into the equations.
From the mass flow rate equation:
ρ₁Av₁ = ρ₂Av₂
Substituting A₁ = 1/2A₂:
ρ₁(1/2)Av₂ = ρ₂Av₂
Canceling out the common terms:
ρ₁/2 = ρ₂
From Bernoulli's equation, we can equate the pressures at the two points:
P₁ + 1/2ρ₁v₁² + ρ₁gh₁ = P₂ + 1/2ρ₂v₂² + ρ₂gh₂
Since the holes are small, the velocity terms (v₁ and v₂) can be assumed to be negligible. Additionally, the pressures at the surface and the holes are atmospheric pressure, so we can ignore those terms as well.
ρ₁gh₁ = ρ₂gh₂
Substituting h₁ = 2h₂ and ρ₁/2 = ρ₂:
2ρ₂g(2h₂) = ρ₂gh₂
Canceling out the common terms:
4h₂ = h₂
Dividing both sides by h₂:
4 = 1
This leads to a contradiction, suggesting that the given conditions are not possible to satisfy. Therefore, there is no valid ratio of the densities of the liquids that would result in the mass flow rate being the same for the two holes.
The ratio p₁/P2 of the densities of the liquids if the mass flow rate is the same for the two holes is 1/2 when The mass flow rate is equal to Av where A is the area of the hole and v is the speed of the liquid emerging from the hole.
Tanks are open, the liquid level will remain constant, so the speed of the liquid emerging from the holes will be the same. Therefore, the ratio of the areas of the holes is the inverse of the ratio of the depths of the holes. Ratio of the cross-sectional areas is 1/2, we have the ratio of the depths of the holes, d1/d2=2.
Speed of the liquid emerging from tank 1 is half that of the liquid emerging from tank 2.If the mass flow rate is the same for both holes, then the mass flow rate out of each hole is equal to the mass flow rate in. The mass flow rate in is proportional to the area of the tank opening.
Tanks are identical, the area of the opening in each tank is the same. Therefore, the density of the liquid in tank 1 is half that of the liquid in tank 2. Therefore, the ratio is p₁/P2=1/2.
Know more about density here:
https://brainly.com/question/6107689
#SPJ11
a spring scale hung from the ceiling stretches by 6.3 cm when a 1.3 kg mass is hung from it. the 1.3 kg mass is removed and replaced with a 2.3 kg mass.
A spring scale hung from the ceiling stretches by 6.3 cm when a 1.3 kg mass is hung from it. The 1.3 kg mass is removed and replaced with a 2.3 kg mass. The stretch of the spring when the 2.3 kg mass is hung is 11.155 N.
The stretch of the spring, Δl is proportional to the mass, m, and the constant of proportionality is the spring constant, k. Δl = km
Let the spring constant be k. When a 1.3 kg mass is hung from the spring, the stretch is Δl = 6.3 cm.
Therefore, 6.3 cm = k (1.3 kg)
Thus, k = 6.3 cm/1.3 kg = 4.85 N/m.
When a 2.3 kg mass is hung from the same spring,
the stretch is Δl = km = (4.85 N/m) (2.3 kg) = 11.155 N.
to know more about spring constant visit:
https://brainly.com/question/13608225
#SPJ11
how deep is the shipwreck if echoes were detected 0.36 s after the sound waves were emitted?
If echoes were detected 0.36 s after the sound waves were emitted, the depth of the shipwreck is 65.52 meters. This can be calculated using the formula:distance = speed × timeWhere speed is the speed of sound in water, which is approximately 1481 meters per second.
The time is 0.36 seconds, as given in the problem.Therefore:
distance = speed × time
distance = 1481 × 0.36
distance = 532.56 meters
However, this distance is the total distance traveled by the sound wave, which includes both the distance from the ship to the bottom and the distance from the bottom to the surface. Since the sound wave travels twice this distance (down to the bottom and back up to the surface), we need to divide by 2 to find the depth of the shipwreck. So, the depth of the shipwreck is:
depth = distance / 2
depth = 532.56 / 2
depth = 265.28 meters
This means that the shipwreck is 265.28 meters deep.
For more information on shipwreck visit:
brainly.com/question/30244941
#SPJ11
Magnetic Field on the Axis of a Circular Current Loop Problem Consider a circular loop of wire of radius R located in the yz plane and carrying a steady current I as in Figure 30.6. Calculate the magnetic field at an axial point P a distance x from the center of the loop. Strategy In this situation, note that any element as is perpendicular to f. Thus, for any element, ld5* xf| (ds)(1)sin 90° = ds. Furthermore, all length elements around the loop are at the same distancer from P, where r2 = x2 + R2. = Figure 30.6 The geometry for calculating the magnetic field at a point P lying on the axis of a current loop. By symmetry, the total field is along this axis,
The net magnetic field on the axis of the circular current loop is given by B=(μ0IR2/2)(x2+R2)-3/2 This is the required expression for the magnitude of the magnetic field on the axis of a circular current loop at a point P which is at a distance x from the center of the loop.
Magnetic field on the axis of a circular current loop at point P which is at a distance x from the center of the loop is calculated by the Biot-Savart law. The magnetic field is given by [tex]B=(μ0/4π)∫dl×r/r3[/tex] where r is the distance between the current element and the point P.
Magnetic field direction is perpendicular to the plane of the loop on the axis of the loop. Let us now find the expression for the magnitude of magnetic field on the axis of a circular current loop.
The geometry for calculating the magnetic field at a point P lying on the axis of a current loop
Let us take the Cartesian coordinate system such that the center of the circular loop is at the origin O. Then the position vector of the current element is [tex]r’=Rcosθi+Rsinθj[/tex] and the position vector of the point P is [tex]r=xk[/tex].
Then the vector r’-r is given by r’-[tex]r=Rcosθi+Rsinθj-xk[/tex]
=(Rcosθi+Rsinθj-xk)
Now the magnitude of this vector is [tex]|r’-r|=√[(Rcosθ-x)2+(Rsinθ)2][/tex]
Then, the magnetic field dB due to this current element is given by [tex]dB=μ0/4π dl/r2[/tex]
where dl=I(r’dθ) is the current element. Now the vector dB can be expressed in terms of its x, y and z components as follows:
[tex]dB=μ0/4π dl/r2[/tex]
=μ0/4π I(r’dθ)/r2 (Rcosθi+Rsinθj-xk)/[R2+ x2 -2xRcosθ+R2sin2θ]
Taking the x-component of dB we get
dB Bx=μ0I[Rcosθ(R2+x2)-xR2cos2θ-R2x]/[4π(R2+ x2 -2xRcosθ+R2sin2θ)3/2]
Integrating the x-component of dB from θ=0 to θ=2π
we get
[tex]Bx=∫dBBx[/tex]
=∫μ0I[Rcosθ(R2+x2)-xR2cos2θ-R2x]/[4π(R2+ x2
-2xRcosθ+R2sin2θ)3/2]dθ=0
Therefore, the net magnetic field on the axis of the circular current loop is given by [tex]B=(μ0IR2/2)(x2+R2)-3/2[/tex]
This is the required expression for the magnitude of the magnetic field on the axis of a circular current loop at a point P which is at a distance x from the center of the loop.
To learn more about Magnetic visit;
https://brainly.com/question/3617233
#SPJ11
What trajectories in the list below are possible for a point charge with some initial velocity in a uniform magnetic field? Check all that apply. O Parabolic Linear Sinusoidal Circular Elliptical Submit Request Answer
In a uniform magnetic field, the possible trajectories for a point charge with some initial velocity are circular and helical. A magnetic field applies a force on a moving charge in a direction perpendicular to the motion of the charge.
As the point charge is moving, the force applied by the magnetic field is perpendicular to both the velocity of the point charge and the direction of the magnetic field.
In the case of circular motion, the force experienced by the point charge is always perpendicular to the velocity and acts as a centripetal force that keeps the point charge moving in a circle. In the case of helical motion, the velocity of the charge and the magnetic field are not parallel, so the charge moves in a helix, which is a combination of circular and linear motion.
The charge moves in a circular path perpendicular to the magnetic field, while also moving in a linear direction parallel to the magnetic field. Thus, in a uniform magnetic field, a point charge with some initial velocity can have circular or helical trajectories.
Therefore, the possible trajectories in the list below that are possible for a point charge with some initial velocity in a uniform magnetic field are: Circular.
Elliptical (as it is a combination of circular and linear motion).
A uniform magnetic field can apply a force on a moving charge in a direction perpendicular to the motion of the charge. In a uniform magnetic field, the possible trajectories for a point charge with some initial velocity are circular and helical.
For more information on magnetic field kindly visit to
https://brainly.com/question/30331791
#SPJ11
how many joules are needed to completely evaporate 25 g of water at 100?
a. 4536 J
b. 24536 J
c. 56425 J
d. 67593 J
The correct option is b. 24536 J. The formula for calculating latent heat of vaporization is Q = m × L, where Q is the amount of heat needed to evaporate m mass of a liquid and L is the latent heat of vaporization of the liquid.
Latent heat of vaporization is the amount of energy required to convert a unit of liquid into a unit of gas without altering its temperature. The formula for calculating latent heat of vaporization is Q = m × L, where Q is the amount of heat needed to evaporate m mass of a liquid and L is the latent heat of vaporization of the liquid. Here, L is the amount of heat required to convert 1 kg of water into 1 kg of steam at atmospheric pressure and 100°C. The value of L for water is 2260 kJ/kg.Let's solve the problem:Mass of water, m = 25 g = 0.025 kgLatent heat of vaporization of water, L = 2260 kJ/kgEnergy required to completely evaporate 25 g of water is given by the formula,Q = m × L= 0.025 kg × 2260 kJ/kg= 56.5 J (approx)
Since the latent heat of vaporization of water at atmospheric pressure and 100°C is 2260 kJ/kg. Since the latent heat of vaporization of water at atmospheric pressure and 100°C is 2260 kJ/kg, the quantity of heat required to evaporate 1 kg of water at 100°C is 2260 kJ. As a result, the energy required to completely evaporate 25 g of water is given by the following formula:Q = m × LHere, m = 25 g = 0.025 kg, and L = 2260 kJ/kg.Q = 0.025 kg × 2260 kJ/kg= 56.5 J (approx)Thus, to completely evaporate 25 g of water at 100°C, we need 24536 J of energy (approx).Therefore, the correct option is b. 24536 J.
To know more about latent heat of vaporization visit :-
https://brainly.com/question/30762921
#SPJ11
A hungry bear weighing 700N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of a beam. The beam is uniform, weighs 200N, and is 6.00m long, and it is supported by a wire at an angle of theta = 60.0 degrees. The basket weighs 80.0N. (a) Draw a force diagram for the beam. (b) when the bear is at x = 1.00m, find the tension in the wire supporting the beam and the components of the force exerted by the wall on the left end of the beam. (c) What If? If the wire can withstand a maximum tension of 900N, what is the maximum distance the bear can walk before wire breaks?
b) The tension in the wire supporting the beam can be calculated as 905.6 N ; c) The maximum distance the bear can walk before the wire breaks is 4.33 m.
(b) The tension in the wire supporting the beam can be calculated using the equation below: T = (mg + mb) / sinθwhere m is the mass of the beam, g is the acceleration due to gravity, mb is the mass of the basket, and θ is the angle of inclination of the wire.T = (m_bean * g + m_basket * g) / sinθwhere m_bean = 200 N / 9.8 m/s² = 20.4 kg is the mass of the beam, g = 9.8 m/s² is the acceleration due to gravity, and m_basket = 80.0 N / 9.8 m/s² = 8.16 kg is the mass of the basket.θ = 60 degrees, sin60° = √3 / 2T = (20.4 kg * 9.8 m/s² + 8.16 kg * 9.8 m/s²) / (√3 / 2) = 349.4 N.
The components of the force exerted by the wall on the left end of the beam can be calculated using the equations below:ΣFx = 0Fx = Nsinθ = 0Nsin60° = 0NΣFy = 0Fy - mg - mb - Tcosθ = 0Fy = mg + mb + TcosθFy = 20.4 kg * 9.8 m/s² + 8.16 kg * 9.8 m/s² + 349.4 N * cos60°Fy = 905.6 N
(c) To find the maximum distance the bear can walk before the wire breaks, we need to find the tension in the wire when the maximum distance is reached. At the maximum distance, the tension in the wire is equal to the maximum tension the wire can withstand, which is 900 N.T = 900 Nsinθ = (mg + mb) / T= sinθ (mg + mb) / T = sinθ (20.4 kg * 9.8 m/s² + 8.16 kg * 9.8 m/s² + 80.0 N) / 900 N = 0.998.
The maximum distance the bear can walk before the wire breaks can be calculated using the equation below: d = (L - x) / cosθd = (6.00 m - 1.00 m) / cos60°d = 4.33 m. Therefore, the maximum distance the bear can walk before the wire breaks is 4.33 m.
To know more about tension, refer
https://brainly.com/question/24994188
#SPJ11
It takes Ben 1s to lift a 2-kg box 2-m above the ground. Calculate the power used in lifting the box. O 3.9 J 1.96 J 39 J O 19.6 J
The power used in lifting the box is 19.6 J.
Power is defined as the rate at which work is done or energy is transferred. It is calculated using the formula:
Power = Work / Time
In this case, the work done is equal to the gravitational potential energy gained by lifting the box:
Work = mgh
where m is the mass (2 kg), g is the acceleration due to gravity (9.8 m/s^2), and h is the height (2 m).
Work = 2 kg * 9.8 m/s^2 * 2 m = 39.2 J
Since it takes Ben 1 second to lift the box, the time is 1 second.
Power = 39.2 J / 1 s = 39.2 J/s
Therefore, the power used in lifting the box is 39.2 J/s, which is equivalent to 19.6 J.
The power used by Ben in lifting the 2-kg box to a height of 2 m is 19.6 J.
To know more about power, visit:
https://brainly.com/question/1634438
#SPJ11
etermine whether the statement makes sense (or is clearly true) or does not make sense (or is clearly false). Explain clearly. Not all of these statements have definitive answers, so your explanation is more important than your chosen answer.
8. Bins. I saw two frequency tables of airline passenger weights, one using bins that spanned 10-pound ranges (e.g., 101 to 110 pounds) and the second with bins that spanned 20-pound ranges (e.g., 101 to 120 pounds). The first table had twice as many categories as the second.
The given statement is true. It is because the first frequency table that spanned the bins with 10-pound ranges had twice the categories compared to the second table that spanned the bins with 20-pound ranges.
A frequency table is a graphical representation of data arranged in intervals along with their respective frequency. It shows how frequent each interval or group of scores is in a given dataset. To construct a frequency table, the given data set is divided into equal intervals called classes or bins.
Frequency tables with bins:
The data can be divided into different bins or classes while making frequency tables. Here, the statement talks about two frequency tables, one with bins that spanned 10-pound ranges, and the other with bins that spanned 20-pound ranges.
This means that in the first table, the interval size is 10 pounds, whereas in the second table, the interval size is 20 pounds.
The number of categories in the first table is twice that of the second table. It means that the first table has more intervals as compared to the second table. It is because the range in the first table is less as compared to the second one, and hence more categories can be created using a smaller range.
So, the given statement makes sense, and it is clearly true.
To know more about frequency visit:
https://brainly.com/question/31938473
#SPJ11
one object has a charge of 5.0 · 10-6 c, and a second object has a charge of 2.0 · 10-6 c. the objects are 0.5 meters apart. what is the electrostatic force between them?
The electrostatic force between the two objects is approximately 3.596 × 10^(-2) N. The electrostatic force between two charged objects can be calculated using Coulomb's law.
The electrostatic force between two charged objects can be calculated using Coulomb's law, which states that the force is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.
The formula for the electrostatic force is:
F = k * (|q1| * |q2|) / r^2
where F is the electrostatic force, k is the electrostatic constant (k ≈ 8.99 × 10^9 N·m^2/C^2), q1 and q2 are the charges of the objects, and r is the distance between the objects.
Plugging in the values:
q1 = 5.0 × 10^(-6) C
q2 = 2.0 × 10^(-6) C
r = 0.5 m
F = (8.99 × 10^9 N·m^2/C^2) * ((5.0 × 10^(-6) C) * (2.0 × 10^(-6) C)) / (0.5 m)^2
Calculating the expression:
F = (8.99 × 10^9 N·m^2/C^2) * (1.0 × 10^(-11) C^2) / (0.5 m)^2
F = (8.99 × 10^9 N·m^2/C^2) * (1.0 × 10^(-11) C^2) / (0.25 m^2)
F = 3.596 × 10^(-2) N
Therefore, the electrostatic force between the two objects is approximately 3.596 × 10^(-2) N.
To learn more about electrostatic force click here
https://brainly.com/question/9774180
#SPJ11
At a given point above Earth's surface, the acceleration due to gravity is equal to 7.8 m/s2. What is the altitude of this point above Earth's surface? (G 6.67 x 10-11 N m2/kg2, Moarth 5.97 x 1024 kg, Rearth 6.38 x 106 m) A) 970 km B) 2400 km c) 1500 km D) 770 km
Option B is correct. The altitude of the given point above Earth's surface is 2400 km.
Given,G = 6.67 × 10^-11 N m^2/kg^2.Mearth = 5.97 × 10^24 kg.Rearth = 6.38 × 10^6 m.Altitude (h) of a point above the Earth's surface where acceleration due to gravity (g) is 7.8 m/s² is to be determined. It is given that g = 7.8 m/s².To calculate h, use the formula: g = (GMearth) / (Rearth + h)²Where,G = Gravitational constant = 6.67 × 10^-11 N m^2/kg^2.Mearth = Mass of Earth = 5.97 × 10^24 kg.Rearth = Radius of Earth = 6.38 × 10^6 m.Substitute the given values in the above equation and simplify it to get h.g = (GMearth) / (Rearth + h)²7.8 = (6.67 × 10^-11 × 5.97 × 10^24) / (6.38 × 10^6 + h)²(6.38 × 10^6 + h)² = (6.67 × 10^-11 × 5.97 × 10^24) / 7.8(6.38 × 10^6 + h)² = 4.25 × 10^13h² + 2 × 6.38 × 10^6 × h + (6.38 × 10^6)² - 4.25 × 10^13 = 0Solve the above quadratic equation to get the value of h.h = 2.4 × 10^6 mTherefore, the altitude of the given point above Earth's surface is 2400 km. Hence, option B is correct.
To calculate the altitude of the given point above Earth's surface where acceleration due to gravity (g) is 7.8 m/s², we use the formula:g = (GM earth) / (R earth + h)²Where,G = Gravitational constant = 6.67 × 10^-11 N m^2/kg^2.Mearth = Mass of Earth = 5.97 × 10^24 kg.R earth = Radius of Earth = 6.38 × 10^6 m.h = Altitude of the point above Earth's surface.Substitute the given values in the above equation and simplify it to get h.g = (GMearth) / (Rearth + h)²7.8 = (6.67 × 10^-11 × 5.97 × 10^24) / (6.38 × 10^6 + h)²(6.38 × 10^6 + h)² = (6.67 × 10^-11 × 5.97 × 10^24) / 7.8(6.38 × 10^6 + h)² = 4.25 × 10^13h² + 2 × 6.38 × 10^6 × h + (6.38 × 10^6)² - 4.25 × 10^13 = 0Solve the above quadratic equation to get the value of h.h = 2.4 × 10^6 mTherefore, the altitude of the given point above Earth's surface is 2400 km.
To know more about altitude visit :-
https://brainly.com/question/31017444
#SPJ11
A teaching assistant is preparing for an in-class demonstration, using insulated copper wire and a power supply. She winds a single layer of the wire on a tube with a diameter of dsolenoid = 10.0 cm. The resulting solenoid is ℓ = 75.0 cm long, and the wire has a diameter of dwire = 0.100 cm. Assume the insulation is very thin, and adjacent turns of the wire are in contact. What power (in W) must be delivered to the solenoid if it is to produce a field of 7.00 mT at its center? (The resistivity of copper is 1.70 ✕ 10−8 Ω · m.) Find the number of turns by dividing the solenoid length by the diameter of the wire. Then apply the relationship between the magnetic field inside a long solenoid and the current. Use your result, along with an expression for the resistance of the wire in terms of resistivity, to calculate the power. In your calculations, you will need the length of the wire. How is the wire length related to the loop circumference and the diameter of the wire? W What If? Assume the maximum current the copper wire can safely carry is 16.0 A. (b) What is the maximum magnetic field (in T) in the solenoid? (Enter the magnitude.) Apply the relationship between the magnetic field inside a long solenoid and the current. Note the current is different from the value found in part (a). T (c) What is the maximum power (in W) delivered to the solenoid? W
The power delivered to the solenoid to produce a field of 7.00 mT at its center is 0.044 W.
What is the power required to generate a 7.00 mT magnetic field in the solenoid?To calculate the power required, we need to consider the number of turns in the solenoid, the current flowing through the wire, and the resistance of the wire.
The number of turns can be found by dividing the length of the solenoid by the diameter of the wire. Once we have the number of turns, we can use the relationship between the magnetic field inside a long solenoid and the current to find the current.
Next, we can calculate the resistance of the wire using the resistivity of copper and the length of the wire. The wire length is related to the loop circumference and the diameter of the wire.
Finally, using the current and resistance, we can determine the power using the formula P = I^2R, where P is the power, I is the current, and R is the resistance.
Learn more about magnetic field
brainly.com/question/14848188
#SPJ11
repeatedly flying into the air and landing on the same spot reinforces to the woodcock (helps it learn) that this is the center of its territory.
The repeated flying into the air and landing on the same spot reinforces to the woodcock that this is the center of its territory.
The phrase "Woodcock sky dances" refers to the woodcock's breeding routine. It is a migratory bird that mates in the United States' Eastern and Central regions. Woodcock "sky dances" or courtship flights, which are a part of its breeding ritual, are familiar to ornithologists and bird lovers.The male woodcock prepares for the display by choosing a place and then creating a tiny opening in the trees or shrubs. It flies into the air at sunset or sunrise, calling out with a distinctive chirping sound. It then lands on the same spot, with each flight being more extensive than the last. The woodcock does this repeatedly, with each flight reaching a greater height than the previous one.
The woodcock's territory is at the center of its sky dancing. The repeated flying into the air and landing on the same spot reinforces to the woodcock that this is the center of its territory. During the breeding season, the woodcock's sky dancing activity is essential. It shows off the male's strength and agility to female woodcocks, which aids in their selection of mates.The woodcock's behavior is a result of natural selection. Through sky dancing, the woodcock's species has developed its breeding ritual over thousands of years. The ability to perform sky dances is an evolutionary benefit to the woodcock, as it aids in species reproduction and survival. Therefore, repeatedly flying into the air and landing on the same spot reinforces to the woodcock that this is the center of its territory.
To know more about breeding routine visit :-
https://brainly.com/question/30073241
#SPJ11
The lenses of a particular set of binoculars have a coating with index of refractionn= 1.38, and the glass itself hasn= 1.52.
Part A:
If the lenses reflect a wavelength of 545 nm the most strongly, what is the minimum thickness of the coating?
If the lenses reflect a wavelength of 545 nm the most strongly, the minimum thickness of the coating the minimum thickness of the coating is 197.83 nm.
the correct option is A. 197.83 nm.
Given data:
The index of refraction of the coating,
n = 1.38
The index of refraction of glass, ng = 1.52
The wavelength of the reflected light,
λ = 545 nm
Part A: The condition for constructive interference is given as:
2nt = m, where n is the refractive index of the material through which the wave is traveling.t is the thickness of the filmm is the order of the interference (for reflection, m=1)λ is the wavelength of the light
When the thickness of the film is increased, the interference becomes more and more constructive. The thickness at which the first constructive interference occurs is given by the above formula. For a thin film between two media, the phase change upon reflection depends on the relative refractive index of the two media.
For a normal incidence of light on a film of thickness t and refractive index n, the path difference between the upper and lower surfaces is 2 nt.
In order to have constructive interference, the path difference must be a multiple of the wavelength, that is, 2nt = m for m = 0, 1, 2, 3, 4,... Since the refractive index of the coating, n, is less than the refractive index of the glass, ng, the phase difference upon reflection from the coating-glass interface is 180° (radians), whereas it is 0° for reflection from the air-coating interface.
The minimum thickness of the film at which the light reflected from the coating-glass interface and the light reflected from the air-coating interface are in phase with each other can be found by substituting m = 1 and solving for t.
This thickness gives the minimum intensity of reflected light.
2nt = mλ
= 1 × 545 nm
= 545 nm
=> t = λ/2n
= 545/(2 × 1.38) nm
= 197.83 nm
Hence, the minimum thickness of the coating is 197.83 nm. Therefore, the correct option is A. 197.83 nm.
To learn more about refraction, visit:
https://brainly.com/question/29692290
#SPJ11
in δmno, m = 150 inches, n = 550 inches and o=630 inches. find the measure of ∠o to the nearest 10th of a degree.
The measure of ∠O in the triangle δMNO is 59.5°.
Given the triangle δMNO where M=150 inches, N=550 inches, and O=630 inches. We need to find the measure of angle ∠O. We can use the Law of Cosines to solve the problem. According to the Law of Cosines,a² = b² + c² - 2bc cos(A) where: a, b, c are the sides of the triangle.
A is the angle opposite to the side a. Applying the Law of Cosines to the triangle δMNO gives us:
OM² = MN² + ON² - 2MN.ON.cos(∠O).
Substituting the given values into the above equation, we have 630² = 550² + 150² - 2(550)(150) cos(∠O).
Simplifying and solving for cos(∠O), we get: cos(∠O) = -0.7063cos(∠O) = -0.7063.
Therefore, ∠O = cos^-1(-0.7063) ≈ 59.5° (to the nearest 10th of a degree). Hence, the measure of ∠O in the triangle δMNO is 59.5°.
Learn more about Law of Cosines here:
https://brainly.com/question/30766161
#SPJ11
the disk is moving to the left such that it has an angular acceleration α = 7 rad/s2 and angular velocity ω = 3 rad/s at the instant shown.(figure 1)
The acceleration at point B and point D is 0.057 m/s².
To determine the acceleration of points B and D on the disk, we need to consider both tangential and centripetal acceleration components.
Angular acceleration (α) = 7 rad/s²
Angular velocity (ω) = 3 rad/s
Radius (r) = 0.5 cm = 0.005 m (converted to meters)
At point A, the disk does not slip, so the tangential acceleration (at) at point A will be zero.
At point B
Tangential acceleration (at) = Radius (r) x Angular acceleration (α)
= 0.005 m × 7 rad/s²
= 0.035 m-rad/s²
Centripetal acceleration (ac) = Radius (r) x Angular velocity (ω)²
= 0.005 m × (3 rad/s)²
= 0.005 m × 9 rad²/s²
= 0.045 m-rad²/s²
The total acceleration (a) at point B will be the vector sum of tangential and centripetal acceleration
a = √(at² + ac²)
= √(0.035)² + (0.045)²
= √0.001225 + 0.002025
= √0.00325
= 0.057 m/s²
At point D
Tangential acceleration (at) = Radius (r) x Angular acceleration (α)
= 0.005 m × 7 rad/s²
= 0.035 m-rad/s²
Centripetal acceleration (ac) = Radius (r) x Angular velocity (ω)²
= 0.005 m × (3 rad/s)²
= 0.005 m × 9 rad²/s²
= 0.045 m-rad²/s²
The total acceleration (a) at point D will be the vector sum of tangential and centripetal acceleration
a = √(at² + ac²)
= √(0.035)² + (0.045)²
= √0.001225 + 0.002025
= √0.00325
= 0.057 m/s²
To know more about acceleration here
https://brainly.com/question/32354429
#SPJ4
-- The given question is incomplete, the complete question is
"The disk is moving to the left such that it has an angular acceleration α =7 rad/s and an angular velocity ω =3 rad/s at the instant shown. If it does not slip at A, determine the acceleration of point B and D."--
A thin film of alcohol (n = 1.36) lies on a flat glass plate (n =1.51). When monochromatic light, whose wavelength can be changed,is incident normally, the reflected light is a minimum for λ =517 nm and a maximum for λ = 650 nm. What is the minimumthickness of the film?
If A thin film of alcohol (n = 1.36) lies on a flat glass plate (n =1.51). When monochromatic light, whose wavelength can be changed,is incident normally, the reflected light is a minimum for λ =517 nm and a maximum for λ = 650 nm then The thickness of the film is 142 nm.
A thin film of alcohol lies on a flat glass plate. When monochromatic light is incident normally, the reflected light is a minimum for λ = 517 nm and a maximum for λ = 650 nm.As we know, for a thin film (whose thickness is less than the wavelength of the incident light) the intensity of the light reflected from the film surface depends on the thickness of the film and the refractive indices of the two media separated by the film.
The reflected light from the film surface is obtained due to the interference between the reflected light from the upper surface and the reflected light from the lower surface of the thin film.The intensity of the reflected light is maximum when the thickness of the film is (2n+1)λ/2 where n is an integer and λ is the wavelength of the incident light.For maximum reflected light, the thickness of the film = (2n+1)λ/2Let us put n = 0, λ = 650 nm.Thus, the thickness of the film for maximum reflected light at λ = 650 nm is: t1 = λ/4μ1= 650 x 10^–9/4 x 1.36 = 119.5 nmFor minimum reflected light, the thickness of the film is nλ/2 where n is an integer and λ is the wavelength of the incident light.For minimum reflected light, the thickness of the film is t2 = nλ/2Putting λ = 517 nm, n = 1, μ1= 1.36, and μ2= 1.51, we get:t2 = λ/4μ2– μ1= 517 x 10^–9/4 (1.51 – 1.36) = 142 nmTherefore, the minimum thickness of the film is 142 nm.
To know more about monochromatic light visit :
https://brainly.com/question/32064872
#SPJ11
n electron in the n=7 level of the hydrogen atom relaxes to a lower energy level, emitting light of 93.1 nm .
The difference in energy between the two levels is equal to the energy of the emitted light, which is given by the equation ΔE = hf, where h is Planck's constant and f is the frequency of the light. In this case, the light emitted by the electron in the n=7 level has a wavelength of 93.1 nm.
When an electron in the n=7 level of the hydrogen atom relaxes to a lower energy level, it emits light of 93.1 nm. The hydrogen atom consists of one proton and one electron. The energy of the electron in an atom is described by its energy level. Electrons in an atom can only occupy specific energy levels.The energy levels are arranged in a series of increasing energy that is given by the formula E = -13.6/n² electron volts (eV), where n is the principal quantum number. When an electron transitions from a higher energy level to a lower energy level, it releases energy in the form of electromagnetic radiation. This energy is directly proportional to the frequency and inversely proportional to the wavelength of the emitted radiation. The difference in energy between the two levels is equal to the energy of the emitted light, which is given by the equation ΔE = hf, where h is Planck's constant and f is the frequency of the light. In this case, the light emitted by the electron in the n=7 level has a wavelength of 93.1 nm.
To know more about hydrogen atom visit :
brainly.com/question/30886690
#SPJ11
Question 8 A force F produces an acceleration a on an object of mass m. A force 3F is exerted on a second object, and an acceleration a results. What is the mass of the second object? Om O (8/31 3mm 24m (3/8) No new data to save. Last checked at 3:42pm Subre MacBook Pro Question ? 3 pts A mass m is traveling at an initial speed vo- 25.0 m/s. It is brought to rest in a distance of 62.5 m boy a force of 15.0 N. The mass is O 1.50 ks O 3.75 kg O 37.5 kg O 6.00 kg 3.00 kg Question 8 3 force F produces an acceleration a on an object of mass m. A force 3F is exerted on a second object, and an MacBook Pro
The mass of the second object is three times the mass of the first object. The mass of the second object is three times the mass of the first object.
To determine the mass of the second object when a force 3F is exerted and results in an acceleration a, we can use the formula F = ma.
Let F be the force that produces an acceleration a on an object of mass m.
Using F = ma,
we can write:F = ma (1) We're given that a force 3F is exerted on a second object, and an acceleration a results.
Using F = ma, we can write:3F = ma (2)
Dividing equation (2) by equation (1), we get:3F / F = ma / ma3 = m2
Therefore, the mass of the second object is three times the mass of the first object. The mass of the second object is three times the mass of the first object.
Learn more about acceleration
brainly.com/question/2303856
#SPJ11
3. An ideal gas undergoes an isothermal expansion process where the final volume is twice the initial volume. a) How are the final and initial temperatures related? Iso thermal AT= 0. b) How are the i
a) The final and initial temperatures are equal in an isothermal process.
b) The initial and final pressures of the gas are inversely proportional in an isothermal process.
Explanation to the above given short answers are written below,
a) The gas undergoes expansion or compression, but the average kinetic energy of the gas molecules and therefore the temperature remain constant throughout the process.
b) According to the ideal gas law,
PV = nRT,
where P is the pressure,
V is the volume,
n is the number of moles,
R is the gas constant, and
T is the temperature.
In an isothermal process, the temperature remains constant, so we have P1V1 = P2V2, where P1 and V1 are the initial pressure and volume, and P2 and V2 are the final pressure and volume.
If the final volume (V2) is twice the initial volume (V1), then we can rewrite the equation as
P1V1 = P2(2V1).
Simplifying further, we get
P1 = 2P2.
This shows that the initial pressure (P1) and the final pressure (P2) are inversely proportional in an isothermal process.
As the volume increases (V2 > V1), the pressure decreases (P2 < P1) to maintain a constant temperature.
To know more about "Isothermal process" refer here:
https://brainly.com/question/12023162#
#SPJ11
The given question is incomplete, so a complete question is written below,
An ideal gas undergoes an isothermal expansion process where the final volume is twice the initial volume. Answer the following questions:
(a) How are the final and initial temperatures related in an isothermal expansion process?
(b) How are the initial and final pressures related in an isothermal expansion process?
7. A 75 kg astronaut orbits the moon at a distance of 2.5 x 106 m from its center. (Mass of moon = 7.35 x 10²² kg) a. What is the force acting on the astronaut by the moon? b. How fast is the astron
a. The force acting on the astronaut by the moon is approximately 2.54 × 10^3 Newtons.
b. The speed of the astronaut orbiting the moon is approximately 1.54 × 10^3 meters per second.
a. To calculate the force acting on the astronaut by the moon, we can use Newton's law of universal gravitation:
F = G * (m1 * m2) / r^2
where:
F is the force,
G is the gravitational constant (approximately 6.67430 × 10^-11 m^3 kg^-1 s^-2),
m1 is the mass of the astronaut (75 kg),
m2 is the mass of the moon (7.35 × 10^22 kg), and
r is the distance between the astronaut and the moon's center (2.5 × 10^6 m).
Let's plug in the values and calculate the force:
F = (6.67430 × 10^-11 m^3 kg^-1 s^-2) * (75 kg) * (7.35 × 10^22 kg) / (2.5 × 10^6 m)^2
F ≈ 2.54 × 10^3 N
Therefore, the force acting on the astronaut by the moon is approximately 2.54 × 10^3 Newtons.
b. To find the speed of the astronaut, we can use the centripetal force equation:
F = (m * v^2) / r
where:
F is the force (calculated in part a, approximately 2.54 × 10^3 N),
m is the mass of the astronaut (75 kg),
v is the speed of the astronaut (what we need to find), and
r is the distance between the astronaut and the moon's center (2.5 × 10^6 m).
Let's rearrange the equation to solve for v:
v^2 = (F * r) / m
v = √((2.54 × 10^3 N * 2.5 × 10^6 m) / 75 kg)
v ≈ 1.54 × 10^3 m/s
Therefore, the speed of the astronaut orbiting the moon is approximately 1.54 × 10^3 meters per second.
a. The force acting on the astronaut by the moon is approximately 2.54 × 10^3 Newtons.
b. The speed of the astronaut orbiting the moon is approximately 1.54 × 10^3 meters per second.
To know more about Force, visit
brainly.com/question/12970081
#SPJ11
Microwave ovens rotate at a rate of about 5.2 rev/min.
What is this in revolutions per second?
What is the angular velocity of this microwave in radians per second?
A truck with 0.420 m radius tires travels at 38 m/s.
What is the angular velocity of the rotating tires in radians per second?
What is the angular velocity of the rotating tires in rev/min?
Angular velocity of truck in rad/min = 90.47 × 60/2π= 861.72 rev/min (Approximately)
Therefore, The answers are, Rev/s of microwave ovens = 0.08667 (Approximately), Angular velocity of microwave oven in rad/s = 0.546 (Approximately), Angular velocity of truck in rad/s = 90.47 (Approximately), Angular velocity of truck in rev/min = 861.72 (Approximately)
Given: Rev/min of microwave ovens = 5.2 rev/min
Rad = 180/π deg
Rad/s = 180/π deg/s1.
To find the Revolutions per second (rev/s) of the microwave oven,
We have given that,
Rev/min of microwave ovens =5.2rev/min
Therefore, Rev/s of microwave ovens = 5.2/60 = 0.08667 rev/s (Approximately)
2. To find the angular velocity (ω) in radians per second (rad/s) of the microwave oven,
We know that, 1 revolution = 2π rad
Therefore,Angular velocity of microwave oven in
rad/s = 5.2 × 2π/60
= 0.546 rad/s (Approximately)
3. To find the angular velocity (ω) in radians per second (rad/s) of the truck,
Given,R = 0.420 m
V = 38 m/s.
Speed of rotation of the tires[tex](v) = Rω[/tex]
ω = v/R
= 38/0.420
= 90.47 rad/s (Approximately)
4. To find the angular velocity (ω) in Revolutions per minute (rev/min) of the truck, We know that, 1 revolution = 2π rad
Therefore, Angular velocity of truck in rad/min = 90.47 × 60/2π = 861.72 rev/min
Therefore, The answers are,Rev/s of microwave ovens = 0.08667 Angular velocity of microwave oven in rad/s = 0.546, Angular velocity of truck in rad/s = 90.47 , Angular velocity of truck in rev/min = 861.72
To learn more about velocity visit;
https://brainly.com/question/30559316
#SPJ11
a lens has a refractive power of -1.50. what is its focal length?
It has been determined that the focal length of the lens is -0.6667 m.
Given: The refractive power of a lens is -1.50We are supposed to find the focal length of the given lens
Solution:The formula to find the focal length of a lens is given by:1/f = (n-1) (1/R1 - 1/R2)
Given: Refractive power (P) = -1.50
As we know that, P = 1/f (Where f is the focal length)
Hence, -1.50 = 1/fOr, f = -1/1.5= -0.6667 m
Therefore, the focal length of the given lens is -0.6667 m.
From the above calculations, it has been determined that the focal length of the lens is -0.6667 m.
To know more about focal length visit:
brainly.com/question/31755962
#SPJ11
suppose we want a satellite to revolve around the earth 4 times a day. what should the radius of its orbit be? (neglect the presence of the moon.)
The radius of the orbit of the satellite should be cuberoot (36) ≈ 3,557 km.
To calculate the radius of an orbit of a satellite revolving around the Earth, we can use Kepler's Third Law of Planetary Motion. Kepler's Third Law states that the square of the orbital period of a planet is directly proportional to the cube of its semi-major axis.
Here's how we can use it to solve the given problem: Given, the satellite has to revolve around the earth 4 times a day.
So, the time period (T) of the satellite can be calculated as follows: T = 24 hours/4 = 6 hours
Now, according to Kepler's Third Law, we can write: T² ∝ r³
Where T is the time period of the satellite and r is the radius of its orbit. As we want the satellite to complete 4 orbits in a day, its time period is 6 hours.
Therefore, substituting the values, we get:6² ∝ r³=> 36 ∝ r³=> r³ = 36
Therefore, the radius of the orbit of the satellite should be cuberoot (36) ≈ 3,557 km.
To learn more about radius visit;
https://brainly.com/question/13449316
#SPJ11
the number of electrons on john represents a difference in charge. his leg is negative compared to the doorknob. why is this considered potential energy?
The fact that John's leg is negative compared to the doorknob indicates that there is a potential difference in charge between the two. This difference in charge is a form of potential energy, which can be released in the form of electrical energy if the charges are allowed to flow through a conductor.
Potential energy is the energy that an object has due to its position or configuration. In other words, it is energy that is stored and available for use. It is represented by the symbol PE and is measured in Joules (J).
Electrons are negatively charged particles that are present in atoms. They are part of the atom's outer shell and are involved in chemical reactions. They can move from one atom to another, creating a flow of electrical charge. Electrons are the basis for electricity and are essential for many of the processes that occur in the natural world.
Therefore, the number of electrons on John's leg represents a difference in charge. His leg is negative compared to the doorknob, which means that there is a potential difference in charge between the two. This difference in charge is a form of potential energy, which can be released in the form of electrical energy if the charges are allowed to flow through a conductor.
Learn more about Potential energy https://brainly.com/question/21175118
#SPJ11
Vectors A, B, and C have the given components. A, 2.01 Ay = 7.0 B₂ = 2.0 By = -5.0 Cx = 6.0 C₂ = 9.0 Find the components of the combinations of these vectors. (A + B) = (A-3.0C) (A+B-C)₁ = (A-3.0C), - (A+B-C), -
The components of the combinations of the given vectors are as follows: (A + B) : (9.01, -3.0), (A-3.0C) : (-15.99, -20.0), (A+B-C)₁ : (3.01, -12.0), -(A+B-C) : (-3.01, 12.0).
To find the components of the combinations of these vectors, we perform vector addition and scalar multiplication according to the given operations.
(A + B) = (A₁ + B₁, A₂ + B₂) = (2.01 + 7.0, 2.0 + (-5.0)) = (9.01, -3.0)
(A-3.0C) = (A₁ - 3.0C₁, A₂ - 3.0C₂) = (2.01 - 3.0 * 6.0, 7.0 - 3.0 * 9.0) = (-15.99, -20.0)
(A+B-C)₁ = (A₁ + B₁ - C₁, A₂ + B₂ - C₂) = (2.01 + 7.0 - 6.0, 2.0 + (-5.0) - 9.0) = (3.01, -12.0)
-(A+B-C) = (-(A+B-C)₁, -(A+B-C)₂) = (-(3.01), -(12.0)) = (-3.01, 12.0)
The components of the combinations of the given vectors are as follows:
(A + B) = (9.01, -3.0)
(A-3.0C) = (-15.99, -20.0)
(A+B-C)₁ = (3.01, -12.0)
-(A+B-C) = (-3.01, 12.0)
To know more about vectors , visit:
https://brainly.com/question/27854247
#SPJ11
Discuss (a) the physical and (b) mathematical relationship in the following figure involving nozzle flow.
a) (a) The increase in nozzle area leads to a decrease in fluid velocity. (b) The Bernoulli equation describes the relationship between fluid velocity and pressure.
b) (a) The decrease in nozzle area leads to an increase in fluid velocity. (b) The continuity equation describes the relationship between fluid velocity and cross-sectional area.
c) (a) The increase in nozzle area leads to an increase in fluid velocity. (b) The Bernoulli equation describes the relationship between fluid velocity and pressure.
d) (a) The decrease in nozzle area leads to a decrease in fluid velocity. (b) The continuity equation describes the relationship between fluid velocity and cross-sectional area.
The decrease in nozzle area leads to an increase in fluid velocity. So the correct option is b) The continuity equation describes the relationship between fluid velocity and cross-sectional area.
The given figure involves nozzle flow, physical and mathematical relationships are discussed below:a) Physical relationship The increase in nozzle area leads to a decrease in fluid velocity due to the following reasons: The nozzle is considered to be a controlled nozzle, i.e., it controls the amount of fluid that flows through it, which results in controlling its velocity. As the nozzle's area increases, the amount of fluid flowing through it increases.
As per the principle of continuity, the mass flow rate should remain constant; hence, the fluid velocity must decrease. Mathematically, it can be represented as: v ∝ 1/A , where v is velocity and A is area.b) Mathematical relationshipThe Bernoulli equation describes the relationship between fluid velocity and pressure. It states that in a steady-state flow, where no work is done on the fluid, the total energy of the fluid remains constant.
To know more about velocity visit:-
https://brainly.com/question/30559316
#SPJ11
When testing gas pumps for accuracy, fuel-quality enforcement specialists tested pumps and found that 1341 of them were not pumping accurately (within 3.3 oz when 5 gal is pumped), and 5650 pumps were accurate. Use a 0.01 significance level to test the claim of an industry representative that less than 20% of the pumps are inaccurate. Use the P-value method and use the normal distribution as an approximation to the binomial distribution. 1.Identify the null hypothesis and alternative hypothesis. 2. Test statists z= 3. p-value= 4.Because the P-value is less than less than greater than the significance level, fail to reject fail to reject reject the null hypothesis. There is insufficient sufficient insufficient evidence support the claim that less than 20% of the pumps are inaccurate
When testing gas pumps for accuracy, fuel-quality enforcement specialists tested pumps and found that 1341 of them were not pumping accurately (within 3.3 oz when 5 gal is pumped), and 5650 pumps were accurate. Use a 0.01 significance level to test the claim of an industry representative that less than 20% of the pumps are inaccurate. Use the P-value method and use the normal distribution as an approximation to the binomial distribution.The null hypothesis and alternative hypothesis:The null hypothesis is that less than 20% of the pumps are inaccurate, and the alternative hypothesis is that more than or equal to 20% of the pumps are inaccurate.The test statistics z and p-value:The sample proportion of pumps that are inaccurate can be calculated by dividing the number of pumps that are inaccurate by the total number of pumps, which is: p = 1341 / (1341 + 5650) = 0.1913The sample size n is 6991. Since the sample size is large, we can use the normal distribution to approximate the binomial distribution of the sample proportion. The test statistic z is calculated as: z = (p - P0) / sqrt(P0(1 - P0) / n) = (0.1913 - 0.2) / sqrt(0.2(1 - 0.2) / 6991) = -3.54The p-value can be calculated as the area to the right of the test statistic z under the standard normal distribution. The p-value is less than 0.0001, which means that the probability of observing a sample proportion as extreme as 0.1913 or more extreme, assuming that the null hypothesis is true, is less than 0.0001.Because the p-value is less than the significance level of 0.01, we reject the null hypothesis and conclude that there is sufficient evidence to support the claim that more than or equal to 20% of the pumps are inaccurate. Therefore, the industry representative's claim that less than 20% of the pumps are inaccurate is not supported by the data. Answer: 1. Null hypothesis: The null hypothesis is that less than 20% of the pumps are inaccurate Alternative hypothesis: The alternative hypothesis is that more than or equal to 20% of the pumps are inaccurate 2. Test statistics z= -3.54 P-value= <0.0001 3. Because the p-value is less than the significance level of 0.01, we reject the null hypothesis and conclude that there is sufficient evidence to support the claim that more than or equal to 20% of the pumps are inaccurate. Therefore, the industry representative's claim that less than 20% of the pumps are inaccurate is not supported by the data.
To know more about hypothesis visit
https://brainly.com/question/29576929
#SPJ11
1. Null hypothesis: H0: p ≥ 0.20; Alternative hypothesis: Ha: p < 0.20
2. Test statistic: z = -12.41 (approx)
3. P-value: P(z < -12.41) < 0.0001 (approx)
4. Because the P-value is less than the significance level, reject the null hypothesis. There is sufficient evidence to support the claim that less than 20% of the pumps are inaccurate.
1. Null hypothesis and alternative hypothesisH0: p ≥ 0.20 (The proportion of pumps that are not pumping accurately is greater than or equal to 20%)Ha: p < 0.20 (The proportion of pumps that are not pumping accurately is less than 20%)where p is the true proportion of pumps that are not pumping accurately.
2. Test statistic: z = (1341 - 0.20 × 6991) / sqrt (0.20 × 0.80 × 6991) = -12.41 (approx)Note: 6991 pumps were tested (1341 + 5650). The null proportion is 0.20. The expected frequency of inaccurate pumps is 0.20 × 6991. The expected frequency of accurate pumps is 0.80 × 6991.
3. P-value: P-value = P (z < -12.41) < 0.0001 (approx) Note: We use the normal distribution as an approximation to the binomial distribution. The continuity correction was not used.
4. Because the P-value is less than the significance level, reject the null hypothesis. There is sufficient evidence to support the claim that less than 20% of the pumps are inaccurate. The industry representative's claim is not valid. The fuel-quality enforcement specialists' findings suggest that the proportion of inaccurate pumps is significantly less than 20%.
To know more about P-value, visit:
https://brainly.com/question/32355626
#SPJ11
waves on a swimming pool propagate at 0.443 m/s. you splash the water at one end of the pool and observe the wave go to the opposite end, reflect, and return in 34.7 s. how far away is the other end?
The given problem can be solved by applying the formula for wave velocity (V), which is given by, V = λf = λ / T, where V is the velocity of the wave, λ is the wavelength of the wave, f is the frequency of the wave, and T is the time period of the wave.
Given data:Velocity of the wave, V = 0.443 m/sTime taken for the wave to go to the opposite end, reflect, and return = 34.7 sWe need to find the distance between the two ends of the pool. Since the wave reflects from the other end, the wave travels twice the distance between the two ends of the pool.So, Distance travelled by the wave = 2d (where d is the distance between the two ends)The time taken by the wave to travel to the other end, reflect and return = 34.7 sSo, we have:2d = V × t= 0.443 × 34.7= 15.3881 mTherefore, the distance between the two ends of the pool is approximately equal to 15.4 m. Answer:15.4 m
For more information on frequency visit:
brainly.com/question/29739263
#SPJ11
Air at 20 degrees celsius flows through the circular duct such that the absolute pressure is 100.8 kPa at A, and 101.6 kPa at B. Determine the volumetric discharge through the duct.
The volumetric discharge through the duct is calculated to be 0.000191 m³/s.
Formula used: Q = (π/4)d²(V1 - V2) where ,d = diameter of the circular ductV1 = volumetric flow rate at section 1V2 = volumetric flow rate at section 2Q = Volumetric discharge Solution: Given, Absolute pressure at A, P1 = 100.8 kPa Absolute pressure at B, P2 = 101.6 kPa Temperature of air, T = 20°CUsing the Ideal gas law,P1/ρ1T1 = P2/ρ2T2where, ρ1 and ρ2 are the densities of the air at section 1 and section 2 respectively.P1/ρ1T = P2/ρ2T
Putting the given values in above equation,100.8/ρ1(20 + 273) = 101.6/ρ2(20 + 273)ρ2/ρ1 = 0.975On comparing with the standard density,ρ/ρ₀ = (P/P₀) / (T/T₀)where, P₀ and T₀ are the standard pressure and standard temperature respectively. The standard pressure is 101.325 kPa and the standard temperature is 273 K.
Substituting the given values,ρ1/ρ₀ = (100.8/101.325) / (293/273) = 0.9285ρ2/ρ₀ = (101.6/101.325) / (293/273) = 0.9339ρ2 = 1.026 ρ1Now, using the Bernoulli's equation, P₁/ρ₁ + V₁²/2 = P₂/ρ₂ + V₂²/2
Assuming the air to be incompressible,ρ1 = ρ2Therefore, P₁ + V₁²/2 = P₂ + V₂²/2V₂²/2 - V₁²/2 = P₁ - P₂V₂² - V₁² = 2(P₁ - P₂)
Now, using the formula, Q = (π/4)d²(V1 - V2) where, d = diameter of the circular ductV1 = volumetric flow rate at section 1V2 = volumetric flow rate at section 2Q = Volumetric discharge
Putting the given values in the above formula,
Q = (π/4)d² [(V1 - V2)]Q = (π/4)d² [(V1² - V₂²)/(V1 + V2)]Q = (π/4)d² [(2(P₁ - P₂))/(V1 + V2)]Q = (π/4)(0.028³)² [(2(101.6 - 100.8))/(2V)]
where V = V1 = V2 (Assuming the air to be incompressible)
V = √[2(101.6 - 100.8)/0.028] = 37.42 m/sQ = (π/4)(0.028³)² [(2(101.6 - 100.8))/(2 x 37.42)] = 0.000191 m³/s
More on volumetric discharge: https://brainly.com/question/27780812
#SPJ11
do all of the planets orbit in the same direction when viewed from bove the earth's north pole
No, not all planets orbit in the same direction when viewed from above the earth's north pole.
The eight planets in the solar system orbit the sun in the same plane. All the planets orbit in the same direction as the sun, which is counterclockwise when viewed from above the solar system. This is also known as the prograde rotation or the direct orbit.However, there are a few exceptions to this rule. Two planets, Venus and Uranus, have a different rotational axis than the rest of the planets.
This means that they appear to be rotating clockwise or retrograde, when viewed from above their respective poles.Venus rotates slowly and in the opposite direction of its orbit, causing the sun to rise in the west and set in the east. Uranus, on the other hand, has an extreme axial tilt, causing it to appear to be rotating on its side, with its poles almost parallel to the plane of the solar system.In summary, not all planets orbit in the same direction when viewed from above the earth's north pole. While the majority of planets in the solar system have a prograde rotation or direct orbit, Venus and Uranus are exceptions to this rule and have a retrograde rotation.
To know more about planets orbit visit :-
https://brainly.com/question/31991442
#SPJ11
