The pressure of hydrogen gas formed in mmHg is 745.7 mmHg. In order to find the pressure of hydrogen gas formed in mmHg, we need to make use of the Dalton's Law of Partial Pressures which states that the total pressure of a gas mixture is equal to the sum of the partial pressures of each individual gas present.
We know that the total pressure of gas collected over water is 770.0 mmHg and that the temperature is 25.5 °C. Since the gas was collected over water, we know that it must have contained some amount of water vapor. This means that the total pressure is equal to the sum of the partial pressures of hydrogen gas and water vapor. Let's use this information to find the partial pressure of hydrogen gas.1.
We can use a table or a graph to find this value. A quick search shows that the vapor pressure of water at 25.5 °C is 24.3 mmHg.2.
Now we can use the Dalton's Law of Partial Pressures to find the partial pressure of hydrogen gas. P total = PH₂ + P water PH₂ = P total - P water
PH2 = 770.0 mmHg - 24.3 mmHg
PH2 = 745.7 mmHg.
Therefore, the pressure of hydrogen gas formed in mmHg is 745.7 mmHg.
To know more about Dalton's Law, refer
https://brainly.com/question/14119417
#SPJ11
how much ice at a temperature of -10.0 ∘c must be dropped into the water so that the final temperature of the system will be 34.0 ∘c ?
The mass of ice needed is 1.94 times the mass of water.
To calculate the amount of ice needed to raise the temperature of water from -10.0 °C to 34.0 °C, we need to consider the heat transfer that occurs during the process.
The amount of heat transferred, Q, can be calculated using the formula:
Q = m_ice * C_ice * ΔT_ice + m_water * C_water * ΔT_water
Where:
Q is the total heat transferred
m_ice is the mass of ice
C_ice is the specific heat capacity of ice
ΔT_ice is the change in temperature of the ice (final temperature - initial temperature)
m_water is the mass of water
C_water is the specific heat capacity of water
ΔT_water is the change in temperature of the water (final temperature - initial temperature)
Since the ice is initially at -10.0 °C and needs to be raised to 0.0 °C (melting point of ice), ΔT_ice = 0 - (-10.0) = 10.0 °C.
Similarly, for the water, ΔT_water = 34.0 - 0 = 34.0 °C.
The specific heat capacity of ice, C_ice, is 2.09 J/(g·°C).
The specific heat capacity of water, C_water, is 4.18 J/(g·°C).
Assuming no heat loss to the surroundings, the heat transferred from the ice to the water is equal to the heat absorbed by the water.
Since the ice is at a lower temperature than the water, it will need to absorb heat to reach its melting point (0.0 °C). The heat absorbed by the ice can be calculated using the formula:
Q_ice = m_ice * C_ice * ΔT_ice
On the other hand, the water needs to absorb heat to reach the final temperature of 34.0 °C. The heat absorbed by the water can be calculated using the formula:
Q_water = m_water * C_water * ΔT_water
Since the heat transferred from the ice to the water is equal, we have:
Q_ice = Q_water
Substituting the values:
m_ice * C_ice * ΔT_ice = m_water * C_water * ΔT_water
Now, we can solve for the mass of ice, m_ice:
m_ice = (m_water * C_water * ΔT_water) / (C_ice * ΔT_ice)
Given that the final temperature of the system will be 34.0 °C, we assume that the water is initially at the same temperature.
Let's say we have a mass of water, m_water, in grams. We can substitute the values and calculate the mass of ice needed:
m_ice = (m_water * 4.18 * 34.0) / (2.09 * 10.0)
Simplifying the equation further, we have:
m_ice = (1.94 * m_water)
Therefore, the mass of ice needed is 1.94 times the mass of water.
In conclusion, to determine the specific mass of ice needed to raise the temperature of water from -10.0 °C to 34.0 °C, you would need 1.94 times the mass of water.
To know more about mass visit:
https://brainly.com/question/837939
#SPJ11
show how could you prepare the following cyclohexenone by combining a stork enamine reaction with an intramolecular aldol condensation by drawing the appropriate pyrrolidine enamine and enone precursors. g
cyclohexanone can be prepared by combining a Stork enamine reaction with an intramolecular aldol condensation by drawing the appropriate pyrrolidine enamine and enone precursors. The Lewis acid catalyst promotes the formation of a cyclic intermediate, which then undergoes dehydration to give the final product, cyclohexenone.
The Stork enamine reaction involves the formation of an enamine from a ketone and a secondary amine, followed by reaction with an electrophile such as an aldehyde. An intramolecular aldol condensation is a reaction in which an enolizable aldehyde or ketone undergoes self-condensation to form an α,β-unsaturated carbonyl compound. The key intermediates in this process are pyrrolidine enamine and enone precursors.
Here's how to prepare cyclohexanone using these reactions:
Step 1: Synthesis of Pyrrolidine Enamine A pyrrolidine enamine can be synthesized by reacting cyclohexanone with pyrrolidine and acetic anhydride. The reaction is carried out in the presence of a catalyst, such as p-Toluenesulfonic acid. The pyrrolidine enamine is then treated with an electrophile, such as an aldehyde, to give the corresponding α,β-unsaturated carbonyl compound.
Step 2: Synthesis of Enone Precursor An enone precursor can be synthesized by reacting cyclohexanone with an aldehyde, such as benzaldehyde, in the presence of a base, such as sodium hydroxide. The reaction is carried out under reflux conditions to promote the formation of an enolate ion. The enolate ion then undergoes self-condensation to form an α,β-unsaturated carbonyl compound.
Step 3: Intramolecular Aldol CondensationThe pyrrolidine enamine and enone precursor can be combined to form cyclohexenone through an intramolecular aldol condensation. The reaction is carried out in the presence of a Lewis acid catalyst, such as boron trifluoride etherate.
The Lewis acid catalyst promotes the formation of a cyclic intermediate, which then undergoes dehydration to give the final product, cyclohexanone.
To know more about cyclohexanone refer to:
https://brainly.com/question/28163979
#SPJ11
When nacl is added to a solution of (i) agno3, (ii) pb(no3)2, or (iii) ca(no3)2, in which case(s) does a precipitate form?
a. Agno3 only
b. Pb(no3)2 only
c. Ca(no3)2 only
d. In all three cases
e. Agno3 and pb(no3)2 only?
A precipitate is formed in all the three cases when NaCl is added to a solution of i) AgNO3, ii) Pb(NO3)2 or iii) Ca(NO3)2. Explanation:In the given cases, when NaCl is added to a solution of AgNO3, Pb(NO3)2 or Ca(NO3)2, a precipitate is formed in all the three cases.
Let's understand it for each case:When NaCl is added to a solution of AgNO3, a white precipitate of AgCl is formed.
AgNO3 + NaCl → AgCl + NaNO3
When NaCl is added to a solution of Pb(NO3)2, a yellow precipitate of PbCl2 is formed.
Pb(NO3)2 + 2NaCl → PbCl2 + 2NaNO3
When NaCl is added to a solution of Ca(NO3)2, a white precipitate of CaCl2 is formed.
Ca(NO3)2 + 2NaCl → CaCl2 + 2NaNO3
Precipitation is one of the common reactions in chemistry, which occurs when two aqueous solutions are mixed. The reactants present in the solution react with each other to form a solid substance called a precipitate. The precipitation reaction can be used to determine the presence of a particular compound in a solution.In the given problem, we need to determine which cases form a precipitate when NaCl is added to a solution of AgNO3, Pb(NO3)2 or Ca(NO3)2. Let's discuss each case in detail:When NaCl is added to a solution of AgNO3, a white precipitate of AgCl is formed. This reaction can be represented as follows:
AgNO3 + NaCl → AgCl + NaNO3
The precipitate formed is white, which confirms the presence of Ag+ ions in the solution. Hence, the answer is (a) AgNO3 only.When NaCl is added to a solution of Pb(NO3)2, a yellow precipitate of PbCl2 is formed. This reaction can be represented as follows:
Pb(NO3)2 + 2NaCl → PbCl2 + 2NaNO3
The precipitate formed is yellow, which confirms the presence of Pb2+ ions in the solution. Hence, the answer is (b) Pb(NO3)2 only.When NaCl is added to a solution of Ca(NO3)2, a white precipitate of CaCl2 is formed. This reaction can be represented as follows:
Ca(NO3)2 + 2NaCl → CaCl2 + 2NaNO3
The precipitate formed is white, which confirms the presence of Ca2+ ions in the solution. Hence, the answer is (c) Ca(NO3)2 only.Therefore, the answer to the given question is (d) In all three cases.
When NaCl is added to a solution of AgNO3, Pb(NO3)2, or Ca(NO3)2, a precipitate is formed in all the three cases. The precipitate formed confirms the presence of Ag+, Pb2+ or Ca2+ ions in the solution. Hence, the correct answer is option (d) In all three cases.
To learn more about yellow precipitate visit:
brainly.com/question/31557667
#SPJ11
when solid naoh pellets (the system) are dissolved in water, the temperature of the water and beaker rises. this is an example of ________
When solid NaOH pellets are dissolved in water, the temperature of the water and beaker rises. This is an example of an exothermic process.
In an exothermic process, energy is released in the form of heat. When the solid NaOH pellets dissolve in water, they undergo an exothermic reaction, resulting in the release of heat energy. The heat energy is transferred to the surrounding water and beaker, causing an increase in temperature.The dissolution of NaOH in water is an exothermic process because the breaking of ionic bonds in the solid NaOH and the formation of new ion-dipole interactions with water molecules releases energy. This energy is released in the form of heat, leading to the temperature increase. Therefore, the rise in temperature observed when solid NaOH pellets are dissolved in water is an example of an exothermic process.
To know more about ion-dipole interactions, click here https://brainly.com/question/30642064
#SPJ11
What is the pH of a buffer made from 0.220 mol of HCNO (Ka = 3.5 × 10⁻⁴) and 0.410 mol of NaCNO in 2.0 L of solution?
PH of the buffer made from 0.220 mol of HCNO (Ka = 3.5 × 10⁻⁴) and 0.410 mol of NaCNO in 2.0 L of solution is pH = 3.46 + 0.269 = 3.73.
A buffer is a solution that resists changes in pH when small amounts of acid or base are added. It is made up of a weak acid and its conjugate base or a weak base and its conjugate acid. A buffer's pH is determined by the ratio of the concentrations of the weak acid and its conjugate base.
To find the number of moles of HCNO we can use the formula; moles = mass / molar mass We are given that we have 0.220 moles of HCNO in a 2.0 L solution so;0.220 mol / 2.0 L = 0.110 M The pH of the buffer can then be determined by plugging in the values into the Henderson-Hasselbalch equation: pH = pKa + log (conjugate base / weak acid)where pKa = -log(Ka)pKa = -log(3.5 × 10⁻⁴)pKa = 3.46 (rounded to two decimal places).
To know more about buffer visit:
https://brainly.com/question/31847096
#SPJ11
determine the idealized bond angle for each molecule. drag the appropriate items to their respective bins.
The bond angle in CF₄ is 109.5°, in NF₃ is 101.9°, in OF₂ is 109° 27′, in H₂S is 92.1°.
The Fluorine atoms all oppose one another, creating a tetrahedral structure, according to the VSEPR hypothesis. Consequently, CF4's bond angle is 109.5°.
The arrangement of the electrons in a molecule constantly seeks to reduce the repulsion between the electrons. The electrons in OF2 are organized in a tetrahedral configuration. As a result, its electron geometry is tetrahedral. F-O-H's bond angle is 109° 27′.
Thus, the bond angle in CF₄ is 109.5°, in NF₃ is 101.9°, in OF₂ is 109° 27′, in H₂S is 92.1°.
Learn more about bond angle, here:
https://brainly.com/question/31324226
#SPJ4
The given question is incomplete, so the most probable complete question is,
Determine the idealized bond angle for each molecule:
CF₄,
NF₃
OF₂
H₂S
1a. If 0.619 g of magnesium hydroxide reacts with 0.940 g of sulfuric acid, what is the mass of magnesium sulfate produced? Mg(OH)2(s)+H2SO4(l)→MgSO4(s)+H2O(l)
The mass of magnesium sulfate produced is 0.929 g. To find the mass of magnesium sulfate produced, we first need to determine the limiting reactant. We can do this by calculating the moles of each reactant using their molar masses.
The molar mass of magnesium hydroxide (Mg(OH)2) is 58.33 g/mol, and the molar mass of sulfuric acid (H2SO4) is 98.09 g/mol.
The moles of magnesium hydroxide can be calculated as follows:
[tex]\[\text{{moles of Mg(OH)}}_2 = \frac{{\text{{mass of Mg(OH)}}_2}}{{\text{{molar mass of Mg(OH)}}_2}} = \frac{{0.619 \, \text{g}}}{{58.33 \, \text{g/mol}}} = 0.0106 \, \text{mol}\][/tex]
Similarly, the moles of sulfuric acid can be calculated as follows:
[tex]\[\text{{moles of H}}_2\text{{SO}}_4 = \frac{{\text{{mass of H}}_2\text{{SO}}_4}}{{\text{{molar mass of H}}_2\text{{SO}}_4}} = \frac{{0.940 \, \text{g}}}{{98.09 \, \text{g/mol}}} = 0.0096 \, \text{mol}\][/tex]
From the balanced chemical equation, we can see that the stoichiometric ratio between magnesium hydroxide and magnesium sulfate is 1:1. This means that for every 1 mole of magnesium hydroxide, we will produce 1 mole of magnesium sulfate.
Since the moles of sulfuric acid (0.0096 mol) are less than the moles of magnesium hydroxide (0.0106 mol), sulfuric acid is the limiting reactant. Therefore, all of the sulfuric acid will be consumed in the reaction.
The molar mass of magnesium sulfate (MgSO4) is 120.37 g/mol. Using the stoichiometry, we can calculate the mass of magnesium sulfate produced:
[tex]\[\text{{mass of MgSO}}_4 = \text{{moles of MgSO}}_4 \times \text{{molar mass of MgSO}}_4 = 0.0096 \, \text{mol} \times 120.37 \, \text{g/mol} = 0.929 \, \text{g}\][/tex]
Therefore, the mass of magnesium sulfate produced is 0.929 g.
To learn more about molar masses refer:
https://brainly.com/question/837939
#SPJ11
Will a precipitate form if 500. mL of 0.050 M AgC2H3O2 is mixed with 300. mL of 0.010M K2SO4? Ksp(Ag2SO4)=1.2´10‒5
The molar solubility of Ag2SO4 is first determined by calculating the ion product of the Ag2SO4 salt, which is are the compared to the Ks p of Ag2SO4. Since Q < K sp, no precipitate forms Given,
Volume of AgC2H3O2 solution = 500. mL Concentration of AgC2H3O2 solution the M Volume of K2SO4 solution = 300. mL Concentration of K2SO4 solution = 0.010 M The dissociation reaction of K2SO4 is represented as:K2SO4 → 2K+ + SO42-AgC2H3O2 is a weak electrolyte, which is partially dissociated in solution as follows:AgC2H3O2 ⇌ Ag+ + C2H3O2-K2SO4 solution dissociates completely into its ions, hence the final ion concentrations can be obtained by multiplying the volumes of
the solutions by the respective ion concentrations.[K+] = 2 × 0.010 M = 0.020 M[SO42-] = 0.010 M[Ag+] = [C2H3O2-] = 0.050 M Let's calculate the ion product of Ag2SO4:Ag2SO4 ⇌ 2Ag+ + SO42-Ion product, Q = [Ag+]2[SO42-] = (0.050)2(0.010) = 2.5 × 10-5Ksp = 1.2 × 10-5Since Q < Ksp, the system is unsaturated and no precipitate will form.
To know more about solution Visit;
https://brainly.com/question/1580914
#SPJ11
calculate the number of grams of solute in of a 0.189m koh solution
a. 2,65
b. 8.42 x 10 -4 g
c. 0.842 g
d. 74.2 g
e. 2.65 x 10 3 g
The number of grams of solute in of a 0.189 m KOH solution is 8.42 x 10^-4 g Therefore, the correct answer is option b.
To calculate the number of grams of solute in of a 0.189 m KOH solution Here's how: Given, molarity of the KOH solution, M = 0.189 mol/L The formula to calculate the molarity of a solution is as follows: Molarity (M) = Number of moles of solute (n) / Volume of solution in litres (V).
We need to calculate the number of grams of solute. We can use the formula given below: Mass = Number of moles * Molar mass We can calculate the molar mass of KOH as follows: Molar mass of KOH (K = 39.10, O = 16.00, H = 1.01) = 39.10 + 16.00 + 1.01 = 56.11 g/mol Substitute the values in the formula: Mass = 0.189 mol * 56.11 g/mol = 10.59 g (approx.)Therefore, the number of grams of solute in 0.189 m KOH solution is 10.59 g (approx.).
To know more about solution visit:
https://brainly.com/question/15757469
#SPJ11
Which of the following statements is/are CORRECT? A.For a chemical system at equilibrium, the concentrations of products and concentrations of reactants stop changing over time.
B.For a chemical system at equilibrium, the reactions stop occurring.
C.For a chemical system, if the reaction quotient (Q) is less than K, reactant must be converted to products to reach equilibrium.
D.For a chemical system at equilibrium, the concentrations of products divided by the concentrations of reactants equals one.
The correct statement from the given options are as follows:A. For a chemical system at equilibrium, the concentrations of products and concentrations of reactants stop changing over time.D. For a chemical system at equilibrium, the concentrations of products divided by the concentrations of reactants equals one
.Explanation:In a chemical equilibrium, the rate of the forward reaction equals the rate of the reverse reaction, which means that the concentration of the products and reactants remain constant with time. Thus, statement A is correct. Additionally, statement D is also correct because at equilibrium, the ratio of the concentrations of products to the concentrations of reactants is a constant value, known as the equilibrium constant.
Thus, the correct options are A and D.The statement B is incorrect. At equilibrium, the reactions continue to occur, and the forward and backward reactions occur at the same rate. The statement C is also incorrect. If Q < K, then the reaction proceeds in the forward direction until the equilibrium state is reached.
To know more about reaction visit:
https://brainly.com/question/30464598
#SPJ11
Rank the following complex ions in order of increasing wavelength of light absorbed.
[Co(H2O)6]3+, [CO(CN)6]3-, [CO(I)6]3-, [Co(en)3]3+
And an explanation please.
The given complex ions can be arranged in increasing order of wavelength of light absorbed as follows: [Co(H2O)6]3+ < [Co(CN)6]3- < [Co(I)6]3- < [Co(en)3]3+.
The wavelength of light absorbed depends on the presence of unpaired electrons in a complex. Due to the crystal field theory, complex ions with fewer d-electrons generally absorb higher energy light, resulting in a shorter wavelength. In contrast, complex ions with more d-electrons absorb lower energy light, resulting in a longer wavelength.The electron configuration of cobalt(III) is 3d6.
Cobalt(III) complexes form, the electrons in the 3d orbitals pair up, leaving no unpaired electrons for transition absorption. Co(III) complex ions only absorb light in the UV region, and they are generally colourless. As a result, we may put the four given complex ions in order of increasing wavelength of light absorbed by comparing their colours.[Co(H2O)6]3+: Pink[V(CN)6]3-: Dark Blue[Co(I)6]3-
To know more about wavelength visit:-
https://brainly.com/question/31143857
#SPJ11
Balance the following redox reaction in acidic solution. ClO3– + Cl– → Cl2 + ClO2
What is the sum of the coefficients in the balanced redox reaction?
The sum of the coefficients in the balanced redox reaction is 17.
In the given redox reaction, we need to balance the equation in acidic solution. The first step is to balance the atoms in the reaction by adding coefficients in front of each compound. We start by balancing the atoms that appear in multiple compounds. By assigning appropriate coefficients, we balance the number of chlorine (Cl) atoms on both sides of the equation.
Next, we balance the number of oxygen (O) atoms by adding water molecules (H₂O) to the equation. We also balance the charge by adding hydrogen ions (H⁺) to the reaction. Finally, we check the overall charge and atom balance to ensure the equation is balanced. After balancing, the coefficients of the balanced equation are: ClO₃⁻ + 6Cl⁻ → 5Cl₂ + ClO₂. The sum of the coefficients is 17, which is the answer to the question.
Learn more about Redox reactions
brainly.com/question/28300253
#SPJ11
the figure to the right shows the graph of a function. match the function with its first derivative and its second derivative.
The second derivative is found by differentiating the first derivative. The first derivative is matched with the function, and the second derivative is matched with the first derivative.
As no figure has been attached to the question, the specific function is not given. Therefore, I will provide a general method that can be used to match a function with its first derivative and its second derivative. Let's have a look below.A function is a rule that maps every input value to exactly one output value. Derivatives are a way of expressing how much a function changes as the input value changes.To obtain the first derivative of a function, we differentiate the function. Differentiation is the process of finding the rate at which a function changes with respect to the independent variable.To find the second derivative of a function, we differentiate the first derivative obtained. The second derivative is the rate at which the first derivative changes with respect to the independent variable.So, to match a function with its first derivative and its second derivative, we will differentiate the function twice. The first derivative will be matched with the function, and the second derivative will be matched with the first derivative.To give a 100 word answer: The process to match a function with its first derivative and second derivative is to differentiate the function twice. Differentiation involves finding the rate of change of a function with respect to the independent variable. To find the first derivative, the function is differentiated once. The second derivative is found by differentiating the first derivative. The first derivative is matched with the function, and the second derivative is matched with the first derivative.
To know more about derivative visit:
https://brainly.com/question/29144258
#SPJ11
A buffer contains significant amounts of ammonia and ammonium chloride.
Enter an equation showing how this buffer neutralizes added aqueous acid (HCl).
Express your answer as a chemical equation. Identify all of the phases in your answer.
The equation for the neutralization of the buffer solution with aqueous hydrochloric acid (HCl) can be represented as follows:
NH3 (aq) + HCl (aq) ↔ NH4+ (aq) + Cl- (aq)
In this equation:
NH3 represents ammonia, which is a weak base.
HCl represents hydrochloric acid, which is a strong acid.
NH4+ represents ammonium ion, which is the conjugate acid of ammonia.
Cl- represents chloride ion, which is the conjugate base of hydrochloric acid.
The reaction is reversible, indicating that both forward and backward reactions occur simultaneously. The ammonia acts as a weak base, accepting a proton (H+) from hydrochloric acid to form ammonium ion (NH4+). Simultaneously, the chloride ion is released into the solution.
It's important to note that the buffer solution's ability to neutralize the added acid comes from the presence of both ammonia (NH3) and its conjugate acid, ammonium ion (NH4+), in significant amounts. The buffer resists large changes in pH by absorbing or releasing protons, depending on the conditions, which helps maintain the solution's acidity within a certain range.
To know more about buffer visit:
https://brainly.com/question/8676275
#SPJ11
air contains 360 ppmv of carbon dioxide. your class room air ducts supplies air such that the concentration of co2 never exceeded 600 ppm, when you may feel tired or sleepy. your room is (600 cubic meter) designed for 40 student capacity and consider room temperature 22 oc and 0.976 atm. on average human produces 900 grams of co2 per day. answer the following (a) what will be the required flow rate to achieve this design at steady state. (b) consider the room was fiiled with ambient air before the start of class, when the room carbon dioxide concentration reaches 400 ppm with the flow rate obtained in part a? (c) when steady state will be achieved?
(a) To maintain the concentration of carbon dioxide less than or equal to 600 ppmv, the required flow rate to achieve the design of the class room at steady state is `5.83×10^−2 m^3/s`.
Explanation:
Given information:
Volume of room (V) = 600 cubic meters Concentration of carbon dioxide (CO2) in air (C_i)
= 360 ppmv Concentration of CO2 in room at maximum capacity
(C_o) = 600 ppmv Temperature (T)
= 22 oC = 22 + 273
= 295 K Pressure (P)
= 0.976 atm
The amount of carbon dioxide produced by each human in one day (m_p) = 900 grams The volume occupied by 1 gram of CO2 gas at room temperature and pressure (V_m) can be calculated using ideal gas law as,`PV = nRT`Here, `P = 0.976 atm`, `V_m = (22.4 L)/mol`, `T = 295 K`, `R = 0.0821 (atm.L)/(mol.K)``n` is the number of moles and it can be calculated as,n = `m_p`/molar mass of CO2 = `m_p`/44 g/mol Now, using ideal gas law,`PV = nRT``V_m * P = (m_p/molar mass of CO2) * R * T``V_m = (m_p/molar mass of CO2) * R * T/P`= (900 g/44 g/mol) × (0.0821 (atm.L)/(mol.K)) × (295 K) / (0.976 atm) `= 23.61 L Now, volume of CO2 produced per person in one day (V_p) `= m_p/V_m`=`900 g / 23.61 L`= 38.11 L Now, for a room designed for 40 students capacity
(b) In steady state, the rate of flow of carbon dioxide in and out of the room will be equal. Initially, the carbon dioxide concentration in the room is C_i= 400 ppmv. Let the volume of the room be V cubic meters, and the carbon dioxide flow rate be F cubic meters per second at steady state. The initial volume of CO2 in the room is then V * C_i. After time t, the volume of CO2 in the room is V * C_i + F * t, since F cubic meters of air containing C_i ppmv of CO2 enters the room each second. When steady state is reached, this volume is equal to the volume of CO2 leaving the room each second, which is F * (C_o – C_i).Equating these two volumes gives, V * C_i + F * t = F * (C_o – C_i)Dividing through by F gives, t = (C_o – C_i) * V / F Substituting the values,` V = 600 m^3``C_i = 400 ppmv``C_o = 600 ppmv``F = 0.0583 m^3/s`t = `(C_o – C_i) * V / F``= (600 ppmv – 400 ppmv) * 600 m^3 / 0.0583 m^3/s``= 20663 s` Therefore, the time it takes for the room carbon dioxide concentration to reach 600 ppmv is 20663 seconds.
(c) Steady state is reached when the carbon dioxide flow rate entering the room equals the carbon dioxide flow rate leaving the room. Hence, steady state will be achieved when the CO2 concentration in the room stops changing or remains within a small range of 600 ppmv.
To know more about concentration of carbon dioxide refer to:
https://brainly.com/question/32507260
#SPJ11
the disk-shaped head of a pin is 1.0 mm in diameter. which of the following is the best estimate of the number of atoms in the layer of atoms on the top surface of the pinhead?
A. 10^14
B. 10^29
C. 10^61
The disk-shaped head of a pin has a diameter of 1.0 mm. We need to estimate the number of atoms on the top surface of the pinhead. The best estimate of the number of atoms in the layer of atoms on the top surface of the pinhead is 1.0 x 10¹⁴ atoms, which is option A. 10¹⁴.
The area of a circle is given by the formula A=πr², where "r" is the radius of the circle and π is pi. If the diameter of the pin is 1.0 mm, then the radius is 0.5 mm.Therefore, the area of the top surface of the pinhead is:A = π(0.5 mm)² = 0.785 mm²The number of atoms on the surface of the pin can be estimated by using the density of the material from which it is made and the atomic weight of the atoms in the material. Let's assume that the pinhead is made of copper, which has a density of 8.96 g/cm³.
The mass of the top surface of the pinhead can be calculated as follows:
mass = density × volume
= 8.96 g/cm³ × 0.785 mm² × (1 cm / 10 mm)²
= 5.57 × 10⁻⁸ g
The atomic mass of copper is 63.55 g/mol. This means that one mole of copper has a mass of 63.55 g, and contains Avogadro's number (6.02 × 10²³) of atoms.
Therefore, the number of atoms in the layer of atoms on the top surface of the pinhead is:(5.57 × 10⁻⁸ g) / (63.55 g/mol) × (6.02 × 10²³ atoms/mol) = 5.87 × 10¹⁴ atoms
Therefore, the best estimate of the number of atoms in the layer of atoms on the top surface of the pinhead is 1.0 x 10¹⁴ atoms, which is option A. 10¹⁴.
To know more about atomic mass refer to:
https://brainly.com/question/30390726
#SPJ11
1. Predict which alkene will predominate at equilibrium. Explain.
2. Predict the stereochemistry of the products formed if the addition of bromine to fumaric acid occurs via:
a. syn addition
b. anti addition.
c. stereorandom addition.
3. The stock solution of bromine for Part B is prepared by dissolving 7.75 g of Br_2 and 6. 25 g of KBr in water and diluting to 25.00 ml. in a volumetric flask. Calculate the molarity of Br_2 in the stock solution. (KBr is present to facilitate the reaction.)
4. The isomerization of dimethyl maleate to dimethyl fumarate can potentially occur by a free radical mechanism, formation of a bromonium cation, or addition of bromine to the double bond via a carbocation to form a dibromide, followed by dehromination. Write detailed mechanistic steps for each of these possibilities.
5. Which compound (dimethyl maleate or dimethyl fumarate) would be expected to have a higher R_f value on TLC? Explain.
1. To predict which alkene will predominate at equilibrium, let us understand what the factors are that can affect the position of an equilibrium. These factors include:
The stability of the reactants and the products
The strength of the reactants and the products
The temperature
The concentration of the reactants and the products
2. We know that fumaric acid exists as a pair of stereoisomers, the trans isomer being fumaric acid, and the cis isomer being maleic acid. Both isomers can undergo addition with bromine, but the products will be different depending on the reaction conditions.
a. Syn addition:
If the addition of bromine to fumaric acid occurs via a syn addition, then the two bromine atoms will be added to the same side of the molecule. The product will be meso-2,3-dibromosuccinic acid.
b. Anti addition:
If the addition of bromine to fumaric acid occurs via an anti addition, then the two bromine atoms will be added to opposite sides of the molecule. The product will be a pair of enantiomers, meso-2,3-dibromosuccinic acid and (R,R)- or (S,S)-2,3-dibromosuccinic acid.
c. Stereorandom addition:
If the addition of bromine to fumaric acid occurs via a stereorandom addition, then the product will be a mixture of the above two products.
3. The molarity of Br_2 in the stock solution can be calculated by first finding the number of moles of Br_2 and KBr in the solution, and then dividing the moles of Br_2 by the volume of the solution in liters.
The molar mass of Br_2 is 2(79.9 g/mol) = 159.8 g/mol.
The number of moles of Br_2 is therefore:
7.75 g / 159.8 g/mol = 0.0485 mol
The molar mass of KBr is 119.0 g/mol.
The number of moles of KBr is therefore:
6.25 g / 119.0 g/mol = 0.0525 mol
The total volume of the solution is 25.00 ml = 0.02500 L.
The molarity of Br_2 in the solution is therefore:
0.0485 mol / 0.02500 L = 1.94 M
4. The isomerization of dimethyl maleate to dimethyl fumarate can potentially occur by a free radical mechanism, formation of a bromonium cation, or addition of bromine to the double bond via a carbocation to form a dibromide, followed by dehromination.
- Free radical mechanism: The reaction proceeds via a radical chain mechanism. The first step is initiation, where the bromine molecule is split into two bromine radicals. The second step is propagation, where the bromine radical adds to the double bond, creating a carbon-centered radical. The third step is another propagation step, where another bromine radical adds to the carbon-centered radical, creating a dibromide radical. The final step is termination, where two radical species combine to form a non-radical product.
- Formation of a bromonium cation: The reaction proceeds via a three-membered cyclic intermediate known as a bromonium ion. The bromine molecule approaches the double bond and forms a bridged intermediate. The bromine molecule is polarized and the carbon-carbon double bond is polarized, so the bromine atom is electrophilic and the carbon-carbon double bond is nucleophilic. The bromine atom forms a bond with one of the carbon atoms, and the other bromine atom takes a pair of electrons from the other carbon atom, forming a cyclic intermediate. The intermediate is then attacked by a nucleophile, such as water, to form the product.
- Addition of bromine to the double bond via a carbocation to form a dibromide, followed by dehromination: The reaction proceeds via the addition of a bromine molecule to the double bond, creating a carbocation. The carbocation then reacts with another bromine molecule, creating a dibromide. The dibromide can then be dehalogenated by a reducing agent, such as zinc dust or sodium hydrogensulfite, to form the product.
5. Dimethyl maleate would be expected to have a higher Rf value on TLC because it is less polar than dimethyl fumarate. The Rf value is a measure of how far a compound travels on a TLC plate relative to the distance traveled by the solvent front. The more polar a compound is, the more it will interact with the polar stationary phase on the TLC plate, and the less it will move up the plate with the solvent front. Since dimethyl maleate is less polar than dimethyl fumarate, it will move further up the TLC plate with the solvent front, giving it a higher Rf value.
learn more about equilibrium here
https://brainly.com/question/517289
#SPJ11
Arrange the elements in decreasing order of first ionization energy.
Rank from highest to lowest first ionization energy. To rank items as equivalent, overlap them.
In, Ge, Se, Cs
The correct arrangement of the given elements in decreasing order of first ionization energy is as : Se >Ge> In > Cs.
The first ionization energy of an element is the energy needed to remove an electron from an atom's outermost shell. As a result, we need to identify the elements among In, Ge, Se, and Cs with the highest to lowest first ionization energy and then arrange them in a decreasing order.
On moving left to right across a period, ionization energy increases as atomic radius decreases and it becomes difficult to remove the outermost electron, whereas, down the group, ionization energy decreases due to increase in atomic radius.
Selenium (Se) has the highest first ionization energy of all the given elements, followed by Germanium (Ge), Indium (In), and Cesium (Cs). Therefore, the correct arrangement of the given elements in decreasing order of first ionization energy is as follows:Se>Ge> In > Cs
This arrangement shows that Selenium (Se) has the highest first ionization energy among all the given elements while Cesium (Cs) has the lowest first ionization energy.
To learn more about ionization energy :
https://brainly.com/question/20658080
#SPJ11
the following chemical reaction takes place in aqueous solution: agno3 nai
The following chemical reaction takes place in aqueous solution: AgNO3 + NaI → NaNO3 + AgI.Here, the reactants are AgNO3 and NaI whereas the products are NaNO3 and AgI. AgNO3 is silver nitrate and NaI is sodium iodide.
NaNO3 is sodium nitrate and AgI is silver iodide.Silver nitrate and sodium iodide react with each other to form sodium nitrate and silver iodide, according to the given chemical reaction in aqueous solution.
This is an example of a double displacement reaction as both reactants exchange ions with each other. The following chemical reaction takes place in aqueous solution: AgNO3 + NaI → NaNO3 + AgI.Here, the reactants are AgNO3 and NaI whereas the products are NaNO3 and AgI. AgNO3 is silver nitrate and NaI is sodium iodide.
To know more about sodium iodide visit :
https://brainly.com/question/19952754
#SPJ11
for each spectroscopy scenario below, which value corresponds to a greater proportion of light absorbed by a sample?
For each spectroscopy scenario below, the value that corresponds to a greater proportion of light absorbed by a sample is a higher molar extinction coefficient and a longer path length.What is spectroscopy. Spectroscopy is a scientific process of examining the interaction of matter and light.
It involves radiated electromagnetic radiation from the matter in a sample, with a wavelength and frequency spectrum that is analyzed. The frequencies in this spectrum relate to the energy that the sample absorbs and re-emits.In general, the amount of light absorbed by a sample depends on the molar extinction coefficient and the path length.
The proportion of light absorbed is directly proportional to the concentration of the sample, which indicates that there is a greater likelihood that more of the light will be absorbed if the molar extinction coefficient is higher and the path length is longer. Therefore, a higher molar extinction coefficient and a longer path length correspond to a greater proportion of light absorbed by a sample.
To know more about spectroscopy visit :
https://brainly.com/question/13265448
#SPJ11
when elemental sodium metal (na) is mixed with ethanol (ch3ch2oh) an exothermic reaction proceeds to give sodium ethoxide (ch3ch2o–/na ) and ______ gas. (fill in the blank.)
When elemental sodium metal (Na) is mixed with ethanol (CH3CH2OH), an exothermic reaction proceeds to give sodium ethoxide (CH3CH2O–/Na) and hydrogen gas (H2).
The balanced chemical equation for the reaction of sodium with ethanol is:2 Na(s) + 2 CH3CH2OH(l) → 2 CH3CH2O–Na+ + H2(g)When sodium metal is mixed with ethanol, the reaction occurs in two steps. In the first step, the electrons of sodium metal are transferred to the ethanol molecules, resulting in the formation of positively charged sodium ions (Na+) and negatively charged ethoxide ions (CH3CH2O–):Na(s) + CH3CH2OH(l) → Na+(aq) + CH3CH2O–(aq) + 1/2 H2(g).
In the second step, the ethoxide ions react with the remaining sodium metal to form sodium ethoxide, while hydrogen gas is produced as a byproduct: Na(s) + CH3CH2O–(aq) → CH3CH2O–Na+(aq) + 1/2 H2(g)Thus, the exothermic reaction between sodium metal and ethanol gives sodium ethoxide (CH3CH2O–Na+) and hydrogen gas (H2).
To know more about reaction visit:
https://brainly.com/question/30464598
#SPJ11
for an isolated system, why entropy change (s2 - s1) cannot be negtive?
For an isolated system, entropy change (s2 - s1) cannot be negative. This is because there is no heat or work transfer to or from the surroundings, which means that the entropy of the system will always increase.
Entropy is the measurement of the degree of randomness or disorder in a system. A positive entropy change in an isolated system signifies that the system is becoming more random or disorderly. The concept of entropy is based on probability theory, where the greater the number of possible configurations of a system, the higher its entropy. Since an isolated system cannot exchange heat or work with its surroundings, the total entropy of the system remains constant or increases with time.
In a reversible process, the entropy change of a system is zero, but in an irreversible process, the entropy of the system increases. The second law of thermodynamics states that the entropy of an isolated system can only increase or remain constant, and it can never decrease. Therefore, the entropy change (s2 - s1) of an isolated system cannot be negative, but can only be zero or positive.
To know more about entropy visit:
https://brainly.com/question/20166134
#SPJ11
what volume of oxygen gas reacts with 30.0 l of sulfur dioxide gas?
The balanced chemical equation for the reaction between sulfur dioxide and oxygen gas can be given as; the volume of oxygen gas required to react with 30.0 L of sulfur dioxide is 30.0 L.
According to the ideal gas law, PV = nRT where P is the pressure of the gas, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature in Kelvin. At the same temperature and pressure, equal volumes of gases contain equal numbers of moles of the gas. Therefore, the volume of oxygen gas required to react with 30.0 L of sulfur dioxide can be calculated by the following steps:
Step 1: Write a balanced chemical equation.SO2(g) + O2(g) → SO3(g)
Step 2: Calculate the number of moles of sulfur dioxide using its volume and molar volume.`30.0 L SO2 × (1 mol SO2/22.4 L SO2) = 1.34 mol SO2`
Step 3: Use the mole ratio from the balanced equation to determine the number of moles of oxygen gas required.`1 mol SO2 : 1 mol O2`
Therefore, `1.34 mol SO2 : 1.34 mol O2`Step 4: Calculate the volume of oxygen gas using the molar volume.`n = PV/RT`
Where n is the number of moles, P is the pressure, V is the volume, R is the ideal gas constant, and T is the temperature in Kelvin.`
V = nRT/P`
The molar volume is the volume occupied by one mole of an ideal gas at standard temperature and pressure (STP) of 273 K and 1 atm of pressure. Its value is 22.4 L/mol at STP. Therefore, `1.34 mol O2 × (22.4 L O2/mol) = 30.0 L O2`
Hence, the volume of oxygen gas required to react with 30.0 L of sulfur dioxide is 30.0 L.
To know more about sulfur dioxide visit
https://brainly.com/question/9720549
#SPJ11
Name the nitrile(s) with formula C_6H_11N that contain an ethyl group branching off the main chain. There are a maximum of 3 compounds that fit the description; if fewer than 3 compounds exist leave the remainder of the spots blank. 1st compound:_____________2nd compound:_________________________3rd compound:___________________________
The three compounds with an ethyl group branching off the main chain are 3-ethylpentanenitrile, 4-ethylpentanenitrile, and 2-ethylhexanenitrile.
The given formula is C6H11N and ethyl is a group that contains two carbon atoms (C2H5). Therefore, there are different ways of arranging the atoms in the formula C6H11N to obtain the three compounds with an ethyl group branching off the main chain. The ethyl grouparrangements are listed below:1st compound:
3-ethylpentanenitrile (CH3CH2CH2CH(CH3)CH2CN)2nd compound: 4-ethylpentanenitrile (CH3CH2CH(CH3)CH2CH2CN)3rd compound: 2-ethylhexanenitrile (CH3CH2CH(CH3)CH2CH2CH2CN)
three compounds with an ethyl group branching off the main chain are 3-ethylpentanenitrile, 4-ethylpentanenitrile, and 2-ethylhexanenitrile.
To know more about ethyl groupvisit:
brainly.com/question/31860652
#SPJ11
at roughly what pressure, , and temperature, , will diamond, graphite, and liquid carbon all exist in equilibrium?4
At equilibrium, diamond, graphite, and liquid carbon coexist at specific P and T determined by the overlapping region of the phase boundaries. Diamond is denser than graphite due to its compact crystal structure.
The phase diagram for carbon shows that at equilibrium, diamond, graphite, and liquid carbon coexist. To determine the pressure (P) and temperature (T) at this equilibrium point, we need to consider the phase boundaries.
The phase boundary between diamond and graphite is at lower pressures and higher temperatures. The phase boundary between diamond and liquid carbon is at higher pressures and higher temperatures. And the phase boundary between graphite and liquid carbon is at lower pressures and lower temperatures.
Therefore, to have all three phases in equilibrium, we need to find the overlapping region where all three phase boundaries intersect. This occurs at a specific pressure and temperature within the phase diagram.
As for which solid form of carbon is more dense, diamond is more dense than graphite. Diamond has a tightly packed, three-dimensional crystal structure, whereas graphite has a layered structure with weak interlayer forces, resulting in a lower density compared to diamond.
To know more about the phase diagram refer here :
https://brainly.com/question/31251128#
#SPJ11
Complete question :
At roughly what pressure, P, and temperature, T, will diamond, graphite, and liquid carbon all exist in equilibrium? Carbon phase diagram Solid I (diamond) Liquid Phar) Solid II (graphite) Which solid form of carbon is more dense? diamond graphite 0 1000 2000 4000 5000 3000 T(K) 6000 O
Select the atom(s) that can hydrogen bond to the positive pole of water: Select the atom(s) that can hydrogen bond to the negative pole of water: 7 0 Determine the maximum number of water molecules that could theoretically form hydrogen bonds with an asparagine molecule at pH 7. number of water molecules: Consider any intermolecular attractions between the asparagine molecule and water to be hydrogen bonds.
The positive pole of water can form hydrogen bonds with atoms that possess a partial negative charge. The negative pole of water can form hydrogen bonds with atoms that possess a partial positive charge.
Hydrogen bonding occurs when a hydrogen atom is attracted to an atom with a partial negative charge. In the case of water, the positive pole (hydrogen atoms) can form hydrogen bonds with atoms that have a partial negative charge, such as oxygen in other water molecules or in other molecules like alcohols and amines. This is because oxygen is more electronegative than hydrogen, creating a partial negative charge on oxygen and a partial positive charge on hydrogen.
On the other hand, the negative pole of water (the oxygen atom) can form hydrogen bonds with atoms that have a partial positive charge. This includes hydrogen atoms in other water molecules or in other molecules that possess a partial positive charge due to differences in electronegativity.
To determine the maximum number of water molecules that could theoretically form hydrogen bonds with an asparagine molecule at pH 7, we consider any intermolecular attractions between the asparagine molecule and water to be hydrogen bonds.
Asparagine contains both an oxygen atom and a hydrogen atom that can participate in hydrogen bonding with water molecules. Therefore, the number of water molecules that can form hydrogen bonds with an asparagine molecule depends on the availability of water molecules and their ability to interact with the oxygen and hydrogen atoms in the asparagine molecule.
Learn more about intermolecular interactions here:
https://brainly.com/question/29362662
#SPJ11
if the true molarity of naoh is 0.09970 m . calculate the percent error using the average molarity value. formula is % error
To calculate the percent error using the average molarity value when the true molarity of NaOH is 0.09970M, we can use the following formula:
% error = [(experimental value - true value) / true value] x 100where, true value = 0.09970MThe experimental value is the average molarity value.
So, let's say we have three experimental values of molarity for NaOH, i.e., M1, M2, and M3, then the average molarity value would be: Mav g = (M1 + M2 + M3) / 3Now, we can calculate the percent error as:% error = [(Mav g - 0.09970) / 0.09970] x 100
The number of moles of dissolved solute per liter of solution is the molarity unit of concentration. Molarity is expressed as the number of millimoles per milliliter of solution when the volume and the number of moles are divided by 1000.
To know more about molarity refer to:
https://brainly.com/question/30404105
#SPJ11
(10 points) An electron, proton and neutron have the same speed. Which has the smallest matter wave wavelength?
When the electron, proton, and neutron move at the same speed, the electron will have the lowest matter wave wavelength of the trio.
The de Broglie wavelength of a particle is given by the equation λ = h / p, where λ is the wavelength, h is Planck's constant, and p is the momentum of the particle. Since the speed of the electron, proton, and neutron is the same, their momentum will be directly proportional to their mass.
Comparing the masses of the three particles, we find that the electron has the smallest mass, followed by the proton, and the neutron has the largest mass.
Therefore, for the same speed, the electron will have the largest momentum, and consequently, the smallest matter wave wavelength.
In summary, the electron will have the smallest matter wave wavelength among the electron, proton, and neutron when they have the same speed.
To know more about the de Broglie wavelength refer here :
https://brainly.com/question/30404168#
#SPJ11
what is the wavelength of light that would be required to perform the cis-trans isomerization of one molecule of 2-butene?
The wavelength of light required for the cis-trans isomerization of one molecule of 2-butene would be in the range of 160-220 nm in the UV region.
To determine the wavelength of light required for the cis-trans isomerization of one molecule of 2-butene, we need to consider the electronic transition involved in the process.
Cis-trans isomerization typically involves the excitation of a π-bond, which corresponds to a π→π* electronic transition. The wavelength of light required for this transition can be estimated using the π→π* absorption maximum.
For 2-butene, the absorption maximum is typically observed in the ultraviolet (UV) range. The approximate range for π→π* transitions is around 160-220 nm.
Learn more about isomerization here:
https://brainly.com/question/28928283
#SPJ11
The wavelength of light required to perform the cis-trans isomerization of one molecule of 2-butene is 600 nm.
The wavelength of light that would be required to perform the cis-trans isomerization of one molecule of 2-butene is 600 nm. The cis-trans isomerization of one molecule of 2-butene is a photochemical reaction that requires light with a certain wavelength.
The energy of the light is related to its wavelength, and since the cis-trans isomerization requires a certain amount of energy, the wavelength of light that can induce this reaction can be determined using the equation:
E = hc/λ
where E is the energy of the light, h is Planck's constant, c is the speed of light, and λ is the wavelength of the light.
To determine the wavelength of light required for cis-trans isomerization, we can rearrange the equation to get:
λ = hc/E
where E is the energy required for isomerization of a single molecule of 2-butene, which is approximately 100 kJ/mol. So, the wavelength of light required for cis-trans isomerization of one molecule of 2-butene is:
λ = (6.626 x 10^-34 J s x 3.0 x 10^8 m/s) / (100,000 J/mol) = 6.626 x 10^-7 m = 600 nm
Therefore, the wavelength of light required to perform the cis-trans isomerization of one molecule of 2-butene is 600 nm.
To know more about isomerization visit:
https://brainly.com/question/30459757
#SPJ11
select the single best answer. compound a exhibits two singlets in its 1h nmr spectrum at 2.64 and 3.69 ppm and the ratio of the absorbing signals is 2:3. compound b exhibits two singlets in its 1h nmr spectrum at 2.09 and 4.27 ppm and the ratio of the absorbing signals is 3:2. which compound corresponds to dimethyl succinate and which compound corresponds to ethylene diacetate? 1455a1455bdimethyl succinateethylene diacetate 1441a1441b1441c
The compound that corresponds to dimethyl succinate is compound A and the compound that corresponds to ethylene diacetate is compound B. The singlet at 2.09 ppm can be attributed to the hydrogen atoms on the methyl group. Hence, compound B corresponds to ethylene diacetate.
The reason for this can be explained based on the information given in the question.
A singlet appearing in the 1H NMR spectra of compounds A and B indicates that there is no nearby hydrogen atom with which the hydrogen atoms in the given singlet are coupled. The number of protons responsible for the singlet signal can be obtained by integrating the area under the peak. The given ratio of the two signals gives the relative number of hydrogen atoms in each environment. Compound A exhibits two singlets at 2.64 ppm and 3.69 ppm in its 1H NMR spectrum in a 2:3 ratio of absorbing signals.Compound B exhibits two singlets at 2.09 ppm and 4.27 ppm in its 1H NMR spectrum in a 3:2 ratio of absorbing signals. Dimethyl succinate, CH3OCOCH2COOCH3, is a compound that has two types of hydrogen atoms. The hydrogen atoms on the methoxy group appear as a singlet at a chemical shift of around 3.7 ppm, and the hydrogen atoms on the methylene group adjacent to the carbonyl group appear as a singlet at a chemical shift of around 2.6 ppm.
Thus, the singlets in the 1H NMR spectrum of compound A can be attributed to these two types of hydrogen atoms. Ethylene diacetate, CH3COOCH2CH2OCOCH3, has three types of hydrogen atoms. The hydrogen atoms on the methyl group adjacent to the carbonyl group appear as a singlet at around 2.1 ppm, the hydrogen atoms on the methylene group in the center appear as a triplet at around 4.2 ppm, and the hydrogen atoms on the ethylene group appear as a quartet at around 4.3 ppm. Thus, the singlets in the 1H NMR spectrum of compound B can be attributed to the methyl group and the chemical shift of 4.27 ppm can be attributed to the hydrogen atoms on the ethylene group. Therefore, the singlet at 2.09 ppm can be attributed to the hydrogen atoms on the methyl group. Hence, compound B corresponds to ethylene diacetate.
To know more about ethylene refer to:
https://brainly.com/question/14797464
#SPJ11