Radius of the circular loop is 0.0091m.
What is magnetic field?Magnetic field is the area around a magnet where the magnetism influence is felt .
What is the magnetic field at the centre of a circular loop?The formula for magnetic field at the centre of a loop isB =(μ)I/2r
where B= Magnetic field at the centre of a circular loopμ= Magnetic permeability =4(π)*10^(-7)
I= current flowing through the loop
r= radius of the loop
Thus, radius of the loop =(4(π)×10^(-7)×5.7)/(2×3.9×10^(-4))=0.0091m
Thus, we can conclude that the radius of the loop is 0.0091m .
Learn more about magnetic field here :
brainly.com/question/24761394
#SPJ1
A cell connected to two bulbs in series lasts longer than a cell connected to the same bulbs in parallel.Explain why?
Because the voltage stays the same while the amps grow, parallel batteries last longer. It will still be a 12 volt system if you connect two 12v 50ah batteries in parallel, but because the amps quadruple to 100ah, the batteries will last longer. Charges are spread among the bulbs in a parallel circuit because they are flowing in several directions over multiple paths. As a result, each bulb will have less charge since the charge is travelling in multiple directions, and the lights will shine less brightly. On the other hand, in a series circuit, there is only one channel and only one location for the charge to travel, meaning that all of the charge is directed at a single lightbulb. As a result, the lightbulb will shine more brilliantly since there is no need to spread the energy. The rule of conservation of energy is not broken because of the difference in power; instead, smaller resistance causes bigger current, which results in brighter lights. The energy traveling from the source to the bulbs remains constant. Because higher power means that more energy in a given time goes quicker from the source to the bulb, brighter lights require more power rather than energy. Because the energy traveling from the source to the bulbs remains constant, the rule of conservation of energy is not being broken; rather, there is merely a difference in power as a result of smaller resistance leading to bigger current, which will result in brighter lights. This means that brighter lights require more power rather than energy since higher power enables more energy to go from the source to the bulb more quickly.
Thank you,
Eddie
A jet of water squirts out horizontally from a hole near the bottom of the tank, as seen in the figure.
If the hole has a diameter of 3.13 mm, what is the height, h, of the water level in the tank? Assume that x = 1.33 m and y = 1.72 m.
The height of the water level in the water tank is 0.011 m.
What is the time taken by a fluid particle to reach the ground?From Newtown's equation of motion, y=U×t+(1/2)gt²As, initial velocity (U) is zero, t= 2y/gt = (2× 1.72)/9.8 = 0.35 s
What's the velocity along x direction?Velocity along x direction= x × t
= 1.33 × 0.35
= 0.46 m/s
What's the height of water level in the tank?As per Bernoulli's theorem, 1/2 × ρ × v² = ρ × g× h
=> h = v²/2g = 0.46²/(2×9.8)
= 0.011 m
Thus, we can conclude that the height of water level is 0.011m.
Learn more about the Bernoulli's theorem here:
brainly.com/question/18724307
#SPJ1
HELP PLS
The minimum frequency for the photoelectric effect of a zinc plate is 9.7 × 10^14 Hz. If a green photon with a wavelength of 532nm strikes the plate, will electrons be emitted? Show your work to support your answer.
yes electrons will be emitted with the kinetic energy of
[tex]30.87 \times 10 { }^{ - 19} j[/tex]
what is photoelectric effect?
In photoelectric effect, the electrically charged particles are released from or within a material when it absorbs electromagnetic radiation.
what is kinetic energy?
It is a form of energy that an object or a particle has by reason of its motion. If work, which transfers energy, is done on an object by applying a net force, the object speeds up and thereby gains kinetic energy.
Given:
wavelength,λ
[tex] = 5.32 \times 10 {}^{ - 8} m[/tex]
Frequency
[tex] = 9.7 \times {10}^{14} [/tex]
Einstein's photoelectric equation
€= w + KE
€ = hc/ λ
[tex] = \frac{6.63 \times {10}^{ - 34} \times 3 \times {10}^{8} } {5.32 \times 10 {}^{ - 8} } [/tex]
[tex]€= 3.73 \times {10}^{ - 18} [/tex]
w=h.f
[tex] = 6.63 \times {10}^{ - 34} \times 9.7 \times {10}^{14} [/tex]
[tex] = 6.43 {10}^{ - 19} j[/tex]
KE = € - W
[tex]37.3 \times {10}^{ - 19} - 6.43 \times {10}^{ - 19} [/tex]
[tex]kE = 30.87 \times {10}^{ - 19} [/tex]
learn more about photoelectric effect from here: https://brainly.com/question/1408276
#SPJ1
How much energy is needed to move an electron in a hydrogen atom from the ground state (n = 1) to n = 3?
The energy needed to move an electron in a hydrogenatome from the ground state (n=1) to n=3 will be 1.93 *10^-18J and 12.09 eV.
How to compute the value?The following can be deduced:
Energy of electron in hydrogen atom is
En = -13.6 /n2 eV
where n is principal quantum number of orbit.
Energy of electron in first orbit = E1 = -13.6 / 12 = - 13.6eV
Energy of electron in third orbit = E3 = -13.6 /32 = -1.51 eV
Energy required to move an electron fromfirst to thirdorbit ΔE = E3- E1
ΔE = -1.51 - ( 13.6) = 12.09 eV
Energy in Joule = 12.09 *l/× 1.6 × 10^-19 = 1.93 × 10^-18 J.
Learn more about energy on:
https://brainly.com/question/13881533
#SPJ1
Complete question:
How much energy is needed to move an electron in a hydrogenatome from the ground state (n=1) to n=3? Give theanswer (a) in joules and (b) in eV.
Three professional wrestlers are fighting over a champion’s belt, and each exerts a force on the belt. Wrestler 1 exerts a force F1=40.0 N in the +x-direction, wrestler 2 exerts a force F2=80.0 N in the negative y-direction, and wrestler 3 exerts a force F3=60.0 N at an angle of 36.9° counterclockwise (anticlockwise) from the +x-direction.
The resultant force of the three professional wrestlers on the championship belt is 98.35 N.
Component of the forces in x - direction
The component of the forces in x -direction is calculated as follows;
Fx = 40 N + 60(cos 36.9)
Fx = 40 N + 47.98 N
Fx = 87.98 N
Component of the forces in y - directionThe component of the forces in y -direction is calculated as follows;
Fy = -80 N + 60(sin 36.9)
Fy = -43.95 N
Resultant forceR = √Fx² + Fy²
R = √( 87.98² + 43.95²)
R = 98.35 N
Thus, the resultant force of the three professional wrestlers on the championship belt is 98.35 N.
Learn more about resultant force here: https://brainly.com/question/25239010
#SPJ1
a ball bearing x is dropped vertically downwards,from the edge of a table and it takes 0.5seconds to hit the floor. Another bearing y leaves from the edge of the table horizontally with a velocity of 5m/s . Find:.
a)the time taken for bearing y to reach the table?
b)the horizontal distance traveled by y before hitting the floor
c)the height of the table top above the floor level
Answer:
See below
Explanation:
A) bearing y reaches the FLOOR in the same amount of time .5 seconds since there is no initial vertical velocity component
B. in .5 seconds y will travel 5 m/s * .5 s = 2.5 meters horizontally
C. d = 1/2 a t^2
= 1/2 (9.81)(.5^2) = 1.23 m table height
(a) Bearing y takes 0.2 seconds to reach the table. (b) Bearing y travels 1 meter horizontally before hitting the floor. (c) The height of the table top above the floor level is 1.225 meters.
a) Time is taken for bearing y to reach the table:
For a horizontal motion, the equation to calculate time is:
Time (t) = Distance (d) ÷ Velocity (v)
Time (t) = Width of the table / Velocity of y
t = 1 / 5
t = 0.2 sec
So, bearing y takes 0.2 seconds to reach the table.
b) Horizontal distance traveled by bearing y before hitting the floor:
Distance (d) = Velocity (v) × Time (t)
d = 5 × 0.2
d = 1 m
So, Bearing y travels 1 meter horizontally before hitting the floor.
c) The height of the table top above the floor level:
h = (1/2) × g × t²
h = (1/2) × 9.8 × (0.5)²
h = (1/2) × 9.8 × 0.25
h = 1.225 m
So, the height of the table top above the floor level is 1.225 meters.
To know more about the height and distance:
https://brainly.com/question/9965435
#SPJ7
Complete the following:
When light is incident through the focal point, and then strikes a mirror, ___
the light will reflect parallel to the principal axis
the light will reflect back through the focal point
the light will not reflect at all
Answer:
the light will reflect parallel to the principal axis
a resistor wire of diameter 0.6cm has a resistivity of 1.0×00000010 ohms m. what length of the wire would be needed to make a 4 ohm resistor
The length of the wire is 1.12m
What is Resistance ?
Resistance is opposition to the current flowing in the circuit.
Given ,
D= 0.6m
R= 0.6/2m
R= 28Ω
rho = 1Ωm
R= rho ×l/A
where R is resistance , l is length ,A is area and rho is resistivity
By applying value and Solving we get,
l= 1.12m
to learn more about Resistance clickhttps://brainly.com/question/24744735
#SPJ9
a dog runs back and forth between its two owners, who are walking toward one another. the dog starts running when the owners are 10 m apart. if the dog runs with a speed of 3 m/s and the owners each walk with a speed of 1.3 m/s how far has the dog traveled when the owners meet
Answer:
11.54 meters
Explanation:
The owners take 10m / (1.3 + 1.3 m/s) = 3.85 seconds to meet
The dog is running at constant speed of 3 m/s for these 3.85 seconds
3 m/s * 3.85 sec = 11.54 meters
is power and voltage the same thing yes or no
The velocity of a body is given by the equation v= a + bx, where 'x' is displacement. The unit of b is .......
Answer:
s^ -1 ( or 1/sec)
Explanation:
Velocity is given in units of displacement / sec
like feet /sec or m/sec
so b would have units of s^-1
(or perhaps a more general term would be time^-1)
Lifting a 81-kg barbell and weights from rest up to a speed of 1.0 m/s in 0.50 s, resisted by the combined weight of the barbell and weights, requires what applied force in N to two significant digits?
Answer:
960 N
Explanation:
answer should have two signif digits
a = change in velocity divided by change in time
1 m/s / .5 s = 2 m/s^2
F = ma a = g + 2 m/s^2 = 9.81 + 2 = 11.81 m/s^2
81 kg * 11.81 m/s^2 = 956.61 N = ~ 960 N (two sig digits)
(Please let me know if this is incorrect....I am not SURE )
A 60 year old person has a threshold of hearing of 79.0 dB for a sound with frequency f=10,000 Hz. By what factor must the intensity of a sound wave of that frequency, audible to a typical young adult, (sound level=43.0 dB) be increased so that it is heard by the older person.
43.DB(decibels)
⇉ Unit conversion
4.3(bels)
4.951NP
4.3(decades)
14.28(octaves)
Interpretations
⇉ Power quantity level
Basic unit dimensions
⇉ ( logarithmic quantity ).
They provided the intensity in decibels for the problem, but they are unsure by what factor to increase it (I) to make the sound loud enough for the elderly person to hear.
Neglect f entirely.
The following equation must be used to convert decibels (dB) to I:
I=(10^(dB/10))*10^-12
Divide the elder person's dB by the younger person's dB after doing this for each dB.
1.8372093023.
Decibels are used to measure sound (dB). A motorcycle engine operating is roughly 95 dB louder than regular conversation, which is around 60 dB louder than a whisper. Your hearing may begin to be harmed if exposed to noise over 70 dB for an extended period of time. Your ears can suffer instant damage from loud noise above 120 dB.
learn more about frequency https://brainly.com/question/254161
#SPJ1
the meaninn of dynamics
Answer:
Dynamics is just a nice word used in physics denoting a branch of physics, related to the study of forces. Usually these forces are not in mechanical equilibrium, else the branch would be statics.
The technology in the picture produces which energy conversion?
O A. Light energy to electrical energy
• B. Thermal energy to kinetic energy
C. Chemical energy to kinetic energy
D. Kinetic energy to electrical energy
[tex] \qquad \qquad \bf \huge\star \: \: \large{ \underline{Answer} } \huge \: \: \star[/tex]
Option D[tex]\textsf{ \underline{\underline{Explanation} }:}[/tex]
The given picture shows a dam, and as we know dam ises water current to produce electricity. as the water current has high kinetic energy, so when it hits and rotates the turbine, the generator produces electricity.
Hence, the correct option will be :
❖ D. Kinetic energy to electrical energy
As mass increases, which of the following is always true?
a. volume decreases
b. density decreases
c. inertia increases
d. all of these
As mass increases, the following which is found to be always true is a corresponding increase in the inertia and is therefore denoted as option C.
What is Inertia?This is defined as the property of a body to resist changes in velocity or motion. Such feature is characterized by the body having the tendency to remain at rest or in uniform motion unless an external force acts on it.
When mass increase, inertia also increases due to the large amount of force which is needed to change the direction or motion of a body in this scenario. On the other hand, when mass decreases, there is a corresponding decrease in the inertia which is present in a given body over a period of time.
This is therefore the reason why mass of a body is directly proportional to its inertia and makes it the most appropriate choice.
Read more about Inertia here https://brainly.com/question/1140505
#SPJ1
If a frying pan has a heat capacity of 500.j∘c and it absorbs 25,000 j of heat, what will be the change in temperature in degrees celsius?
Answer:
50° C change
Explanation:
25000 J / (500 J/ °C) = 50 ° C
[tex] \large{\rm{Question:}}[/tex]
Give one example where the displacement is zero but the distance traveled is not zero.
Let us assume a man travelled from a point A to a point B over a distance 'd'. After a while he travels the same distance back to point A.
Therefore, since his initial and final positions are the same, displacement is equal to zero, and the distance travelled is (d + d) = 2d, which is not zero.
Example:
Imagine a person walks 10 meters forward and then turns around and walks 10 meters back to the starting point. In this case, the displacement is zero (starting point to ending point), but the distance traveled is 20 meters (10 meters forward + 10 meters backward).
An object with a mass of m = 122 kg is suspended by a rope from the end of a uniform boom with a mass of M = 74.9 kg and a length of l = 8.77 m. The end of the boom is supported by another rope which is horizontal and attached to the wall as shown in the figure.
Calculate the tension in the horizontal rope. (The horizontal and the vertical ropes are not connected to each other. They are both independently attached to the end of the boom.)
The the tension in the horizontal rope is 7,019.4 N.
What is tension?
Tension is described as the pulling force transmitted axially by the means of a string, a cable, chain, or similar object, or by each end of a rod.
Tension can also be described as the action-reaction pair of forces acting at each end of said elements.
The unit of tension is Newton (same unit as force, since tension is also a force).
Tension in the horizontal ropeThe tension in the horizontal rope is calculated as follows;
Apply the principle of torque;
T(L/2) cosθ = Mg (L/2) sinθ + mg L sinθ
T = (M + 2m)g sinθ/cosθ
T = (M + 2m)g tanθ
let θ = 66⁰ (this value should be given in the question)
T = (M + 2m)g tanθ
T = (74.9 + 2 x 122)(9.8)(tan 66)
T = 7,019.4 N
Thus, the the tension in the horizontal rope is 7,019.4 N.
Learn more about tension here: https://brainly.com/question/918617
#SPJ1
A transverse mechanical wave is traveling along a string lying along the x-axis. The displacement of the string as a function of position and time, y(x,t), is described by the following equation:
[tex]y(x,t)=0.0480[/tex]×[tex]sin(5.40x-128t)[/tex]
where x and y are in meters and the time is in seconds.
1. What is the wavelength of the wave?
2. What is the velocity of the wave? (Define positive velocity along the positive x-axis.)
3. What is the maximum speed in the y-direction of any piece of the string? (Give a positive answer for speed.)
The wavelength of the wave is 1.16m and the velocity is 23.64m/s.
To find the answer, we have to know more about the Transverse waves.
How to find different parameters of a wave?The displacement of the string as a function of position and time, y(x,t), when the wave traveling along a string lying along the x-axis is given as,[tex]y(x,t)=0.048sin(5.40x-128t)[/tex]
Comparing this with the general form of wave equation, we get,[tex]amplitude, a=0.048m\\wave vector, k=5.40\\angular frequency,w=128Hz[/tex]
We have to find the wavelength of the wave, for this, we have the expression as,[tex]k=\frac{2\pi }{wavelength} \\\\wavelength=\frac{2\pi }{k} =\frac{2*3.14}{5.40} \\\\wavelength=1.16m[/tex]
We have to find the velocity of the wave,[tex]v=frequency*wavelength\\2\pi f=w, thus,\\f=\frac{w}{2\pi } =\frac{128}{2*3.14}=20.38s^{-1}\\\\v=1.16*20.38=23.64m/s[/tex]
Thus, we can conclude that, the wavelength of the wave is 1.16m and the velocity is 23.64m/s
Learn more about the transvers waves here:
https://brainly.com/question/25746208
#SPJ1
A coin is placed next to the convex side of a thin spherical glass shell having a radius of curvature of 17.0 cm. Reflection from the surface of the shell forms an image of the 1.5-cm-tall coin that is 6.50 cm behind the glass shell.
a) Where is the coin located?
b) Determine the size of the image.
(a) The position of the coin placed next to the convex side of a thin spherical glass shell is 3.68 cm.
(b) The size of the image is 1.8.
Position of the coinThe position of the coin placed next to the convex side of a thin spherical glass shell is calculated as follows;
1/d = 1/f - 1/d'
where;
d' is the position of the coin's imaged position of the coinf is focal lengthFocal length = r/2 = 17 cm / 2 = 8.5 cm
1/d = 1/8.5 - (-1/6.5)
1/d = 1/8.5 + 1/6.5
1/d = 0.1176 + 0.1538
1/d = 0.2714
d = 1/0.2714
d = 3.68 cm
Size of the imageMagnification, M = d'/d
M = (6.5)/(3.68)
M = 1.8
Thus, the position of the coin placed next to the convex side of a thin spherical glass shell is 3.68 cm.
The size of the image is 1.8.
Learn more about magnification here: https://brainly.com/question/1599771
#SPJ1
the apparent weight of a student in alift is 564N . if the mass of the student is 60.3kg, what is the acceleration of the lift ? use negative is the acceleration vector is pointing downwards
Answer:
-.457 m/s^2
Explanation:
Actual weight = 60 .3 (9.81) = 591.54 N
Accel of lift changes this to 60.3 ( 9.81 - L) where L - accel of lift
60.3 ( 9.81 - L ) = 564
solve for L = .457 m/s^2 DOWNWARD
so L = - .457 m/s^2
When a 6kg block is placed on a vertical spring, the spring is compressed by 20cm. How much work is required to compress the spring by an additional 10CM
Answer:
Mass of block = 6kg
wright = 6 × g = 60 N using g = 10 m/s^2 .
compression= 0.20m
spring constant =( weight / compression) =( 60/0.20) = 300 N/m .
Work done in compressing 0.20 m =( 1/2 × 300 × 0.20 × 0.20)= 6 joule.
Additional compression = 0.10 m
total compression = 0.20+ 0.10= 0.30 m.
Total work done = ( 1/2 × 300 × 0.30× 0.30) = 13.5 joule.
Hence work done in compressing from 0.20 m to 0.30 m will be = ( 13.5 - 6) = 7.5 joule.
Note :- work done in compressing a spring having spring constant K N/m by x m is equal to 1/2× (K) × X^ 2 .
A sensor that generates voltages in the range of -2V..+2V for 0..400kg weight values Design a balance circuit with LCD display. ; fosc=4MHz
4. A hemispherical surface (half of a spherical surface) of radius R is located in a uniform electric field of magnitude E that is parallel to the axis of the hemisphere. What is the magnitude of the electric flux through the hemisphere surface? how to draw the question?
It is to be noted that the magnitude of the electric flux through the hemisphere surface is πR²E. (Option D)
What is an Electric Flux?
The characteristic of an electric field known as electric flux may be thought of as the quantity of electric lines of force (or electric field lines) that cross a certain region.
According to this theory, electric field lines begin with positive electric charges and end with negative charges.
What is the calculation for the above?
Recall that the A hemispherical surface (half of a spherical surface) of radius R.
In order to derive the Magnitude of the electric flux we use the following formula:
Ф = ∈ x Area of the Curve Surface
⇒ Ф = ∈ x πR²
⇒ Ф = πR²∈
Thus, option D is the correct answer.
Learn more about Electric Flux:
https://brainly.com/question/14372859
#SPJ1
Full Question:
A hemispherical surface (half of a spherical surface) of radius R is located in a uniform electric field of magnitude E that is parallel to the axis of the hemisphere. What is the magnitude of the electric flux through the hemisphere surface?
A) 2πR²∈
B) 0
C) 4 πR²∈/3
D) πR²∈
i. Which of the following formula gives definition of relative density? d d B. A. C. d water at 4°C d d mercury at 4°C D. d water at 40°C d d alcohol at 4°C
Answer:
water at 4°c that's abnormal stage of water
A thin-walled hollow sphere has a radius 4cm from the center
of the sphere, the eletric field points radially inward and
has a magnitude of 1.5 × 10^4 NC". How much charge is on the surface
The electric charge on surface is 2.66×10-⁹NC
What is an electric charge?The electric charge is the property of subatomic particle that causes it to experience a force when placed in an electric and magnetic field.
We have given ,
Electric field= 1.5×10⁴N/C
Radius = 4cm = 0.04m
E = k× q/ r²
1.5×10⁴×16×10-⁴/9×10⁹=q
q= 2.66×10-⁹C
to learn more about Charge click here https://brainly.com/question/28185654
#SPJ9
A light bulb in a camper’s flashlight is labeled 4.1 V, 0.40 A. Find the equivalent current if three of these light bulbs are connected in parallel to a standard C size 1.5 V battery.
Explanation:
first rule of parallel circuits : the voltage is the same in the whole circuit, no matter where we measure.
so, we have 1.5V at every bulb.
second rule of parallel circuits : the total current is the sum of the individual branch currents.
so, if the battery really allows it, then we have 3 times 0.4 A = 3×0.4 = 1.2 A as current in the circuit.
The object that ends up with less electrons has a __________ charge.
A. Positive
B. Not enough info
C. Neutral
D. Negative
Reset Selection
The object that ends up with less electrons has a positive charge; option A.
What are electrons?Electrons are negatively charged particles which form a part of the three fundamental particles in an atom.
Electrons can easily be removed from the vicinity of atoms making the atom to become positively charged. On the other hand, when atoms gain extra electrons, they become negatively-charged.
On way of charging objects is by rubbing them against other objects in order to gain extra electrons or to lose electrons.
When two objects are rubbed together, the object that ends up with less electrons has a positive charge, whereas the object that ends up with more electrons has a negative charge.
In conclusion, objects can become charged when they are rubbed against each other, and they can either become negatively or positively-charged by gain or loss of electrons.
Learn more about electrons at: https://brainly.com/question/17163716
#SPJ1
The object indicated here that ends up with fewer electrons has an unknown charge (not enough info, Option B).
What does atomic charge mean?The atomic charge makes reference to the overall charge of an atom, which can be evidenced by knowing its net charge (positive or negative charge).
The net charge of a molecule and/or atom is obtained by calculating the amount of electrically negative electrons (e-) and the number of positive protons.
Neutrons are another type of subatomic particle that have not net charge (neither positive nor negative).
In conclusion, the object indicated here that ends up with fewer electrons has an unknown charge (not enough info, Option B).
Learn more about atomic charges here:
https://brainly.com/question/18102056
#SPJ1
What phase of matter is pictured below? Image of particles that are spread out, many are not touching, high energy. A. Gas B. Bose-Einstein condensate C. Fermionic condensate D. Plasma
Option(d)i.e, Plasma is the Image of particles that are spread out, many are not touching, high energy.
Along with solid, liquid, and gas, plasma is frequently referred to as the "fourth state of matter." Heating a gas will result in the formation of plasma, which is a soup of positively and negatively charged particles (ions), similar to how adding energy causes a liquid to boil and transform into a gas (electrons).
Plasmas are less dense than solids or liquids and, like gases, have no set structure or volume. However, in contrast to regular gases, plasmas are composed of atoms in which part or all of the electrons have been removed and positively charged nuclei, known as ions, are free to move around.
Solids, liquids, gases, ionized plasma, quark-gluon plasma, bose-einstein condensate, and fermionic condensate are the seven states of matter.
To know more about plasma refer to: https://brainly.com/question/12847806
#SPJ1
