The recommended procedure while climbing to an assigned altitude on the airway is a) to climb on the centerline of the airway except when maneuvering to avoid other air traffic in VFR conditions.
This helps maintain separation from other aircraft and ensures that the assigned altitude is reached efficiently and safely. It is important to always follow the assigned altitude and stay on the designated airway to avoid any potential conflicts with other aircraft. An air traffic controller is a professional who works in the aviation industry and is responsible for managing the flow of air traffic in and out of an airport or designated airspace. Air traffic controllers use radar and communication systems to direct the movement of aircraft, ensuring that they maintain safe distances from each other and follow designated flight paths. They provide pilots with weather and flight information, issue instructions for takeoff and landing, and monitor the movement of aircraft to prevent collisions and delays. Air traffic controllers must have extensive training and knowledge of aviation regulations, procedures, and technology, and they must be able to work under high pressure and in a fast-paced environment.
Learn more about air traffic here:
https://brainly.com/question/11399320
#SPJ11
What service is provided by departure control to an IFR flight when operating from an airport within the outer area of Class C airspace?
A. Separation from all aircraft.
B. Position and altitude of all traffic within 2 miles of the IFR pilot's line of flight and altitude.
C. Separation from all IFR aircraft and participating VFR aircraft.
When operating from an airport within the outer area of Class C airspace, departure control provides separation from all IFR aircraft and participating VFR aircraft.
Therefore, the correct answer is C - Separation from all IFR aircraft and participating VFR aircraft.
Class C airspace is typically designated around airports with moderate to high volumes of air traffic. Departure control is responsible for providing separation services to aircraft departing from these airports. This includes maintaining separation between IFR aircraft and participating VFR aircraft, which are aircraft operating in visual meteorological conditions and communicating with air traffic control.
Departure control may also provide traffic information to IFR aircraft, such as the position and altitude of all traffic within 2 miles of the IFR pilot's line of flight and altitude, as mentioned in option B. However, this is not the primary service provided by departure control in Class C airspace.
Learn more about Class here:
https://brainly.com/question/30436591
#SPJ11
true or false Context-sensitive grammars, which restrict the right-hand side (replacement
pattern) to have at least as many symbols as the left-hand side (search pattern)
False. Context-sensitive grammars restrict the left-hand side and the right-hand side to have the same number of symbols or for the right-hand side to have one more symbol than the left-hand side.
This means that the replacement pattern in a production rule can be at least as long as the search pattern but not shorter.
Context-sensitive grammars are a type of formal grammar used in the field of theoretical computer science and computational linguistics. They are more powerful than context-free grammars but less powerful than unrestricted grammars. Context-sensitive grammars can generate languages that are not context-free but can still be recognized by a linear bounded automaton (LBA).
Learn more about Context-sensitive here:https://brainly.com/question/24126181
#SPJ11
Which of these is not a good rule to follow when caring for an injured person at an accident scene?
When caring for an injured person at an accident scene, it is important to follow certain rules to ensure their safety and wellbeing.
However, not all rules are good to follow, and some may even be harmful. For example, one rule that is not good to follow is to move an injured person without proper training or equipment.
This can cause further injury and even paralysis. It is important to wait for medical professionals to arrive and assess the situation before attempting to move the injured person.
Another rule that is not good to follow is to administer medication without proper knowledge or training. This can lead to adverse reactions and further harm to the injured person.
It is best to leave medication administration to medical professionals. Following these rules will help ensure the safety and wellbeing of the injured person.
To learn more about : accident scene
https://brainly.com/question/30205063
#SPJ11
8. What section of the OSH Act does the Whistleblower Program reference?
The Whistleblower Program of the Occupational Safety and Health Administration (OSHA) references Section 11(c) of the Occupational Safety and Health Act.
Section 11(c) of the OSH Act prohibits employers from discriminating against employees who file a complaint, report an injury or illness, or exercise any other right under the OSH Act.
The Whistleblower Program enforces this section by investigating and remedying retaliation complaints filed by employees who have been retaliated against for engaging in protected activity. The program also enforces whistleblower protection provisions in other statutes, such as the Surface Transportation Assistance Act and the Sarbanes-Oxley Act.
learn more about Assistance here :
https://brainly.com/question/2456175
#SPJ11
what is the correct mysql command to modify the values stored in a record?
The combined movement of water and air in an irrigation system can present a tremendous hazard to piping, joints, but especially to rotor sprinklers. The air in the lines causes a sharp increase in flow velocity which can damage _______________.
The combined movement of water and air in an irrigation system can present a tremendous hazard to piping, joints, but especially to rotor sprinklers. The air in the lines causes a sharp increase in flow velocity which can damage the rotor sprinklers by causing them to spin too fast or too erratically, leading to premature wear and tear or even failure.
This is known as water hammer, a phenomenon that occurs when water is abruptly stopped or forced to change direction, causing a shock wave that can damage pipes, fittings, and sprinklers. To prevent water hammer, irrigation systems are designed with air release valves or vents that allow air to escape the system, reducing the pressure and velocity of the water.
Additionally, installing pressure regulators can help control the flow of water and prevent damage to the system. Proper maintenance and regular inspection of irrigation systems can also help identify and address any issues before they become major problems. Ultimately, understanding the potential hazards of the combined movement of water and air in an irrigation system is crucial to maintaining the system's functionality and longevity.
Learn more about irrigation systems here: https://brainly.com/question/12820487
#SPJ11
Reception of signals from a radio facility, located off the airway being flown, may be inadequate at the designated MEA to identify the fix. In this case, which altitude is designated for the fix?
1. MOCA.
2. MRA.
3. MCA.
In the case where reception of signals from a radio facility, located off the airway being flown, may be inadequate at the designated MEA to identify the fix, the altitude designated for the fix is the Minimum Crossing Altitude (MCA).
The MCA is the lowest altitude at certain fixes at which an aircraft must cross when proceeding in the direction of a higher minimum en route IFR altitude.
It ensures that an aircraft crossing a fix at a certain altitude will maintain the required obstacle clearance while proceeding to the next fix or destination.
The MOCA (Minimum Obstruction Clearance Altitude) is the lowest published altitude that provides obstruction clearance for the entire route segment and the MRA (Minimum Reception Altitude) is the lowest altitude for reliable reception of VOR signals.
learn more about altitude here :
https://brainly.com/question/4390102
#SPJ11
What are the two places you should never place your main pipelines under?
You should never place your main pipelines under buildings or bodies of water.
Placing main pipelines under buildings can lead to structural damage and make it difficult to access and maintain the pipes in case of a problem. Additionally, in the event of a leak or rupture, it can pose a significant risk to the occupants of the building.
Similarly, placing main pipelines under bodies of water can be problematic as it can cause environmental damage and contamination in case of a leak or rupture.
It can also make it difficult to access and repair the pipelines, especially in deep water or rough weather conditions. Therefore, it is important to carefully consider the location of main pipelines during the planning and construction phases to minimize potential risks and ensure proper maintenance and operation.
For more questions like Pipelines click the link below:
https://brainly.com/question/31082785
#SPJ11
55) ________ grants the owner exclusive ownership of the ideas behind an invention for 20 years.
A) Copyright law
B) Trademark law
C) Patent law
D) Trade secret protection
E) Privacy law
Patent law grants the owner exclusive ownership of the ideas behind an invention for 20 years. Thus, option C is appropriate.
The area of intellectual property law that addresses new inventions is patent law. Circuit boards, automobile engines, heating coils, and zippers are a few examples of tangible scientific inventions that are protected by traditional patents.
A technical product, technique, or invention is protected by a patent. The patented product or method cannot be manufactured, used, sold again, rented out, or supplied by anyone else. However, the patent holder may authorize others to do so by issuing patent laws.
Utility patents, design patents, and plant patents are the three different sorts of patents. For new and practical inventions, utility patents are granted. Design patents safeguard a product's appearance or design. Patents for plants that can reproduce are given to applicants.
Thus, option C is correct.
Learn more about Patent law here:
https://brainly.com/question/31144078
#SPJ4
Iterated logarithm log* and Inverse ackermann function α
The iterated logarithm log* and inverse Ackermann function α are both important concepts in computer science and mathematics. The iterated logarithm log* is a function that describes how many times one must take the logarithm of a given number before the result becomes less than or equal to one.
This function grows very slowly, so it is useful for analyzing the running time of certain algorithms. For example, the running time of some search algorithms is proportional to log* of the number of items being searched. The inverse Ackermann function α is also used to analyze the running time of certain algorithms, particularly those involving data structures such as union-find. This function is even slower-growing than log*, meaning that algorithms with a running time proportional to α(n) are considered very fast. The inverse Ackermann function is also important in the design and analysis of parallel algorithms. In summary, both the iterated logarithm and inverse Ackermann function are important tools for analyzing the running time of algorithms, with the former being useful for certain types of search algorithms and the latter being useful for analyzing data structure and parallel algorithms.
Learn more about iterated logarithm here-
https://brainly.com/question/14473303
#SPJ11
Draw some simple logic gates with CMOS transistors.
CMOS (Complementary Metal-Oxide-Semiconductor) technology is commonly used to implement logic gates. There are several types of logic gates such as AND, OR, NOT, NAND, NOR, XOR, and XNOR gates.
To draw simple logic gates with CMOS transistors, we can use a combination of p-channel and n-channel MOSFETs. For example, an AND gate can be implemented with two n-channel MOSFETs in series and two p-channel MOSFETs in parallel,
while an OR gate can be implemented with two n-channel MOSFETs in parallel and two p-channel MOSFETs in series. Similarly, NOT gates can be implemented with a single n-channel or p-channel MOSFET.
To summarize, CMOS technology is widely used to implement logic gates due to its low power consumption, high speed, and ease of manufacturing. The combination of p-channel and n-channel MOSFETs can be used to design various logic gates.
To learn more about : logic gates
https://brainly.com/question/29558048
#SPJ11
You can access a file in an unmounted file system.
Select one:
a. True
b. False
The given statement "You can access a file in an unmounted file system" is false. An unmounted file system is not currently in use by the operating system, and the file system's data structures, such as the file allocation table or inode table, are not currently available in memory.
In general, you cannot access a file in an unmounted file system. To access a file in a file system, the file system must first be mounted, which makes the file system's data structures available to the operating system. Once a file system is mounted, you can then navigate the file system's directory hierarchy and access files as needed.
It is possible to perform some limited operations on an unmounted file system, such as running file system repair utilities or examining the file system's metadata using specialized tools. However, these operations typically require low-level access to the file system's data structures and are not appropriate for general file access.
To know more about operating system visit:
https://brainly.com/question/31551584
#SPJ11
What is the term for a commercial vehicle's habit of swinging wide on turns?
The term for a commercial vehicle's habit of swinging wide on turns is called "off-tracking".
This refers to the tendency of the vehicle's rear wheels to take a wider path than the front wheels when turning. Off-tracking is common in larger vehicles such as tractor-trailers and buses due to their longer wheelbases and overall length. Off-tracking can be a safety concern for drivers of smaller vehicles as the wider turning radius of the commercial vehicle can encroach on adjacent lanes or even sidewalks. To mitigate this risk, drivers of commercial vehicles are trained to take wider turns and be aware of their vehicle's off-tracking tendencies. Additionally, some cities have implemented "truck aprons" or raised curbs at corners to provide more space for commercial vehicles to turn without encroaching on other lanes or pedestrians.
Overall, it is important for all drivers to be aware of the off-tracking tendencies of commercial vehicles and take appropriate caution when sharing the road with them.
Learn more about pedestrians here: https://brainly.com/question/30051546
#SPJ11
What causes the northerly turning error in a magnetic compass?
A) Centrifugal force acting on the compass card.
B) Coriolis force at the mid latitudes.
C) The magnetic dip characteristic.
The correct answer is C) The magnetic dip characteristic.the northerly turning error in a magnetic compass.
Northerly turning error is a compass error that causes the compass to indicate a turn in the opposite direction to the actual turn when turning to a northerly heading or when reversing a turn from a northerly heading. This error is caused by the vertical component of the Earth's magnetic field, which tilts the compass needle downward when the aircraft is turning to a northerly heading, and upward when the aircraft is turning to a southerly heading. The error is most pronounced when the aircraft is flying at mid-latitudes where the magnetic dip is greatest.
To learn more about error click the link below:
brainly.com/question/29870686
#SPJ11
24. Where there is no specific OSHA standard, employers must comply with the OSH Act's:
General Duty Clause.
The General Duty Clause of the Occupational Safety and Health (OSH) Act requires employers to provide a workplace free from recognized hazards that are causing or are likely to cause death or serious physical harm to employees.
This applies when there is no specific OSHA standard that applies to the particular hazard or workplace situation. Employers must identify hazards and take reasonable steps to address them in accordance with the General Duty Clause.
learn more about Clause here :
https://brainly.com/question/19711531
#SPJ11
You are working with pipe that has no labeling and you're trying to determine its standard dimension ratio (SDR). The pipe has an average outside diameter of 6.625 inches and a minimum wall thickness of 0.255 inches. What is the pipe's SDR rating?
To determine the pipe's standard dimension ratio (SDR) with an average outside diameter of 6.625 inches and a minimum wall thickness of 0.255 inches, follow these steps:
Understand the SDR formula: SDR = Outside Diameter / Wall ThicknessPlug in the given values: SDR = 6.625 inches / 0.255 inchesPerform the calculation: SDR ≈ 25.98The pipe's SDR rating is approximately 25.98.
The Standard Dimension Ratio (SDR) is an important parameter used in the design and installation of piping systems. It refers to the ratio of the pipe's outside diameter to its wall thickness and is used to ensure that pipes can withstand the internal and external pressures they will encounter during operation. In the case of a pipe with an average outside diameter of 6.625 inches and a minimum wall thickness of 0.255 inches, the SDR can be determined by dividing the outside diameter by the wall thickness using the formula SDR = Outside Diameter / Wall Thickness.
Learn more about Standard Dimension Ratio: https://brainly.com/question/29525030
#SPJ11
after refrigerant liquid has been recovered from the appliance, any remaining vapor is;
After the refrigerant liquid has been recovered from the appliance, any remaining vapor is considered non-condensable gases (NCGs) and residual refrigerant vapor.
During the recovery process, the majority of the refrigerant is extracted, leaving these remnants behind.
The NCGs, such as air or nitrogen, can negatively affect the performance of the appliance if not removed properly.
It is essential to follow proper refrigerant recovery procedures and use recovery equipment designed to handle and eliminate NCGs and residual refrigerant vapor.
By doing so, you can ensure the appliance operates efficiently and minimize any potential environmental impact.
Learn more about vapor at
https://brainly.com/question/17121780
#SPJ11
42) Zero defects cannot be achieved in larger software programs because fully testing programs that contain thousands of choices and millions of paths would require thousands of years.
A) TRUE
B) FALSE
Zero defects cannot be achieved in larger software programs because fully testing programs that contain thousands of choices and millions of paths would require thousands of years, is the true statement. Hence, option A is correct.
In general, worms propagate more swiftly over networks than viruses since they are self-replicating and don't require human participation. The reproduction process can be slowed down by viruses.
Debugging is the procedure used to identify and fix the causes of mistakes when they are found in software applications. To create a secure connection between two computers, the SSL protocol is employed.
Thus, option A is correct.
For more information about software, click here:
https://brainly.com/question/985406
#SPJ4
28) Microsoft Access's data dictionary displays all of the following information about a field except the:
A) size of the field.
B) format of the field.
C) description of the field.
D) type of the field.
E) the organization within the organization that is responsible for maintaining the data.
Microsoft Access's data dictionary displays all of the following information about a field except the organization within the organization that is responsible for maintaining the data. Thus, option E is correct.
An automatic or manually tool for organising and organising specifics regarding the data kept in a database is a data dictionary. The structure and substance of data are categorised and communicated using a data dictionary, which also offers insightful descriptions for specially designated data types. One or more attributes that separate each record you store in the database make up a primary key. Therefore, option E is correct.
Learn more about dictionary, here:
https://brainly.com/question/8897251
#SPJ4
How many sends are available on a track in Pro Tools?
In Pro Tools, the number of sends available on a track depends on the version of the software being used and the hardware capabilities of the computer or system being used to run it.
Generally, the number of sends available is determined by the number of available auxiliary tracks that can be used as destinations for the sends. In Pro Tools Standard, there are typically up to 10 sends available per track, while in Pro Tools Ultimate, the number of available sends can be expanded to up to 64 per track. However, these numbers can vary depending on the specific version and edition of the software being used, as well as the computer or system hardware specifications. Sends are an essential part of the mixing process in Pro Tools, as they allow users to route audio from one track to another in order to apply processing or add effects. They are useful for creating complex mixes with multiple layers of effects, and can be used creatively to achieve unique sonic textures and soundscapes.
In conclusion, the number of sends available on a track in Pro Tools depends on the software version and hardware capabilities of the computer or system being used. It can range from 10 sends per track in Pro Tools Standard to up to 64 sends per track in Pro Tools Ultimate.
Learn more about hardware here: https://brainly.com/question/3186534
#SPJ11
(3) 555 ohm resistors, (2) comparators, an RS flipflop, a discharge NPN, an output buffer
The components you mentioned - (3) 555 ohm resistors, (2) comparators, an RS flip-flop, a discharge NPN, and an output buffer - can be combined to form a variety of electronic circuits with different functions. Here is an example of a circuit that can be constructed using these components:
The circuit is a simple pulse generator that generates a short pulse whenever a voltage is applied to its input. The pulse is then amplified and sent to the output buffer, which can drive a load such as an LED or a speaker.
Here's how the circuit works:
1. When a voltage is applied to the input, the voltage is divided between the two resistors and fed into the two comparators.
2. The first comparator is set up as a Schmitt trigger, which means that it will only output a high voltage when the input voltage is above a certain threshold. The second comparator is set up as a simple voltage comparator.
3. When the input voltage rises above the Schmitt trigger threshold, the first comparator outputs a high voltage. This triggers the RS flip-flop, which sets its output to a high voltage and triggers the second comparator.
4. The second comparator detects the high voltage at the output of the RS flip-flop and triggers the discharge NPN transistor, which discharges the timing capacitor and resets the RS flip-flop.
5. The discharge NPN transistor also triggers the output buffer, which generates a short pulse that can drive a load.
This circuit can be useful in applications such as triggering a camera shutter, controlling a motor, or generating an audible tone. Of course, there are many other circuits that can be constructed using these components, depending on the specific requirements of the application.
Learn more about circuits here:
https://brainly.com/question/27206933
#SPJ11
tools made from high-speed tool steel are generally used for what type of machining operations
Tools made from high-speed tool steel are generally used for machining operations that involve high-speed cutting of metals.
High-speed tool steel is a type of tool steel that is designed to withstand high temperatures generated during high-speed cutting operations. The alloy composition of high-speed tool steel includes elements such as tungsten, molybdenum, cobalt, and vanadium that increase its strength, hardness, and wear resistance.
The high-speed cutting operations that use tools made from high-speed tool steel include drilling, milling, turning, and threading of materials such as steel, stainless steel, and aluminum alloys. These operations require high cutting speeds and feed rates to remove material quickly and efficiently while maintaining precision and surface finish.
Therefore, the tools made from high-speed tool steel are ideal for machining operations that require high-speed cutting and can provide superior performance and longer tool life.
Learn more about machining operations visit:
https://brainly.com/question/31526518
#SPJ11
Marco is an English-language learner whose writing skills are comparable to his grade level peers. He is able to write for formal and informal purposes based on the audience. What level of English-language proficiency is Marco in writing?
Based on the given information, it can be inferred that Marco has a proficient level of English-language proficiency in writing.
His writing skills are comparable to his grade level peers, which indicates that he has a good grasp of English grammar and vocabulary. Additionally, he is able to write for both formal and informal purposes depending on the audience, which suggests that he is able to adapt his language use to different contexts. Overall, these indicators point to a proficient level of English-language proficiency in writing for Marco.
learn more about English-language proficiency here:
https://brainly.com/question/30243196
#SPJ11
What effect would a light crosswind of approximately 7 knots have on vortex behavior?
1. The downwind vortex would tend to remain over the runway.
2. The upwind vortex would tend to remain over the runway.
3. The light crosswind would rapidly dissipate vortex strength.
A light crosswind of approximately 7 knots will have a negligible effect on the behavior of vortices.
The vortices will continue to drift with the wind and eventually dissipate due to atmospheric turbulence and mixing. The downwind vortex will still move away from the runway and the upwind vortex will still move towards the runway, but the crosswind will cause them to drift to the side of the runway. The strength of the vortices will also diminish over time due to mixing with surrounding air. It's important for pilots to be aware of vortex behavior and take appropriate precautions when operating in the vicinity of larger aircraft to avoid potential hazards.
Learn more about Vortex here:
https://brainly.com/question/30899462
#SPJ11
Natural language processing (NLP) is associated with which of the following areas?
A Text mining
B Sentiment analysis
C Topic modeling
D All of the above
Natural Language Processing (NLP) is a field of study that focuses on the interaction between human language and computers. It involves the use of computer algorithms to process and analyze large amounts of natural language data.
NLP has numerous applications, including text mining, sentiment analysis, and topic modeling. Text mining involves extracting relevant information and knowledge from unstructured text data, while sentiment analysis is the process of identifying and categorizing opinions expressed in text. Topic modeling is the process of discovering abstract topics that occur in a collection of documents. Therefore, NLP is associated with all of the above areas.
Learn more about computer algorithms here:
https://brainly.com/question/31006849
#SPJ11
88) Why are "conversations" relevant to social business?
Short Answer:
While you are flying at FL 250, you hear ATC give an altimeter setting of 28.92" Hg in your area. At what pressure altitude are you flying?
1. 26,000 feet.
2. 24,000 feet.
3. 25,000 feet.
The answer is 25,000 feet. When ATC gives an altimeter setting, it is essentially providing the current barometric pressure in the area.
Pilots use this information to set their altimeters to accurately display their altitude above mean sea level. At FL 250, the standard altimeter setting of 29.92" Hg would typically be used, but if ATC gives a different setting, pilots must adjust their altimeters accordingly. In this case, the altimeter setting of 28.92" Hg indicates lower atmospheric pressure than standard, which means the altimeter will read higher than the actual altitude. By adjusting the altimeter setting, the true pressure altitude can be determined. In this scenario, the correct pressure altitude at FL 250 with an altimeter setting of 28.92" Hg is 25,000 feet.
learn more about barometric pressure here:
https://brainly.com/question/3083348
#SPJ11
true or false - First-order logic is incomplete and undecidable
First-order logic is incomplete and undecidable, so the statement is true. This means that there are some statements in first-order logic that cannot be proven true or false.
And there is no algorithm that can determine whether a given statement is true or false. This is in contrast to propositional logic, which is both complete and decidable.
First-order logic is incomplete and undecidable, meaning that it cannot express or prove all possible statements and that there is no algorithm that can determine the truth or falsity of all possible statements.
Incompleteness refers to the fact that there are true statements that cannot be proven within the system of first-order logic. This was proven by Kurt Gödel in his incompleteness theorems, which showed that any formal system that is powerful enough to express basic arithmetic is either incomplete or inconsistent. First-order logic is one such formal system, and as a result, there are statements that can be neither proved nor disproved within it.
Undecidability refers to the fact that there is no algorithmic procedure that can determine
learn more about undecidable here :
https://brainly.com/question/30187947
#SPJ11
true or false
Water hammer is the impact force caused by the sudden adjustment in pressure due to changes in the velocity of water traveling through an open channel.
The given statement "Water hammer is the impact force caused by the sudden adjustment in pressure due to changes in the velocity of water traveling through an open channel" is FALSE because water hammer is actually the pressure surge that occurs in a piping system when the flow of water is suddenly stopped.
This sudden stoppage causes a shock wave that travels through the pipe and can cause damage to the system if not properly managed.
The statement is incorrect because it describes a different phenomenon related to the movement of water through an open channel. This phenomenon is called hydraulic jump, which occurs when there is a sudden increase in the depth of water flow, resulting in a rapid increase in pressure and a corresponding decrease in velocity.
In summary, water hammer is a pressure surge caused by sudden changes in the flow of water in a pipe, while hydraulic jump is the sudden adjustment in pressure due to changes in the velocity of water traveling through an open channel.
For more questions like Pipe click the link below:
https://brainly.com/question/13260061
#SPJ11
If the sprinkler head continues to Spray water when the communication tube is clamped what is the problem?
The problem is that the sprinkler head is not controlled by the communication tube and is likely due to a malfunction in the sprinkler head itself.
The communication tube in a sprinkler system is responsible for controlling the flow of water to the sprinkler heads. If the tube is clamped, it should prevent water from reaching the sprinkler head and stop it from spraying.
If the sprinkler head continues to spray water despite the communication tube being clamped, then there is likely a problem with the sprinkler head itself, such as a valve or diaphragm that is not functioning properly.
This can cause water to continue flowing even when it should be shut off. It's important to address this issue as soon as possible to prevent water waste and potential damage to the sprinkler system.
For more questions like Sprinkler click the link below:
https://brainly.com/question/31586848
#SPJ11
