The approximate coefficient of friction is approximately -0.25.
The force of kinetic friction can be calculated using the equation [tex]F_{friction} = \mu_k N[/tex], where [tex]F_{friction}[/tex] is the force of kinetic friction, [tex]\mu_k[/tex] is the coefficient of kinetic friction, and N is the normal force.
In this scenario, the player comes to a stop, indicating that the force of kinetic friction is equal in magnitude and opposite in direction to the force exerted by the player.
We know that the player's initial velocity is 7 m/s and the distance covered while sliding is 5 meters.
To calculate the deceleration (negative acceleration) experienced by the player, we can use the equation [tex]v^2 = u^2 + 2as[/tex]
where v is the final velocity (0 m/s), u is the initial velocity (7 m/s), a is the acceleration, and s is the displacement (5 meters).
Rearranging the equation, we have [tex]a=\frac{v^{2}-u^{2} }{2s}[/tex].
Plugging in the given values, we get [tex]a=\frac{0-(7^2)}{2\times 5} =-2.45 m/s^2[/tex].
Since the force of friction opposes the player's motion, we can assume it has the same magnitude as the force that brought the player to a stop. This force is given by the equation
[tex]F_{friction} = ma[/tex], where m is the mass of the player.
The normal force acting on the player is equal to the player's weight, N = mg, where g is the acceleration due to gravity.
Now, we can substitute the values into the equation [tex]F_{friction} = \mu_kN[/tex]and solve for the coefficient of kinetic friction:
[tex]ma = \mu_k mg[/tex].
The mass of the player cancels out, leaving us with [tex]a = \mu_k g[/tex].
Substituting the calculated acceleration and the acceleration due to gravity, we have [tex]-2.45 m/s^2 = \mu_k 9.8 m/s^2[/tex].
Solving for [tex]\mu_k[/tex], we find [tex]\mu_k = \frac{(-2.45)}{(9.8)} \approx -0.25[/tex].
Thus, the approximate coefficient of friction is approximately -0.25.
Learn more about friction here: brainly.com/question/24338873
#SPJ11
2. Now you try one. Suppose that charge 1 has a magnitude of +6.00μC, charge 2 of +5.00μC, and charge 1 is located at 4.00cm i +3.00cm ĵ and charge 2 is located at 6.00cm î-8.00cm j. Find F12 and
Given information Magnitude of charge 1 = +6.00μCMagnitude of charge 2 = +5.00μCLocation of charge 1 = 4.00cm i +3.00cm j Location of charge 2 = 6.00cm i -8.00cm j Find the force between charge 1 and charge 2.
Force between the two charges is given byF12 = (kq1q2) / r^2Where k is the Coulomb’s constant and is given byk = 9 x 10^9 Nm^2/C^2q1 and q2 are the magnitudes of the charges and r is the distance between the two charges.F12 = (9 x 10^9 Nm^2/C^2) (6.00μC) (5.00μC) / r^2First, find the distance between the two charges.
We know that charge 1 is located at 4.00cm i + 3.00cm j and charge 2 is located at 6.00cm i - 8.00cm j. Distance between the two charges is given byr = √((x₂-x₁)² + (y₂-y₁)²)r = √((6.00 - 4.00)² + (-8.00 - 3.00)²)r = √(2.00² + 11.00²)r = √125r = 11.18cmPutting the value of r in the formula of F12, we haveF12 = (9 x 10^9 Nm^2/C^2) (6.00μC) (5.00μC) / (11.18cm)²F12 = 17.3 x 10^5 NThe force between the two charges is 17.3 x 10^5 N.Answer:F12 = 17.3 x 10^5 N.
To know more about Magnitude visit:
https://brainly.com/question/31022175
#SPJ11
A rod made of insulating material has a length L=7.3 cm, and it carries a chatge of Q=−230 n C that is not distributed uniormly in the fod. Twice as much charge is on one side of the rod as is on the other. Calculate the strength of the rod's electric field at a point 4 m away from the rod's center along an axis perpendicular to the rod. 32 V/m 108Vim 70 Vim 121 Vim 54Vim 130 Vim 100 Vim B. V/M
The strength of the electric field at a point 4 m away from the center of the rod, along an axis perpendicular to the rod, is 54 V/m.
To calculate the electric field strength, we can divide the rod into two segments and treat each segment as a point charge. Let's assume the charge on one side of the rod is q, so the charge on the other side is 2q. We are given that the total charge on the rod is Q = -230 nC.
Since the charges are not uniformly distributed, we need to find the position of the center of charge (x_c) along the length of the rod. The center of charge is given by:
x_c = (Lq + (L/2)(2q)) / (q + 2q)
Simplifying the expression, we get:
x_c = (7.3q + 3.652q) / (3q)
x_c = (7.3 + 7.3) / 3
x_c = 4.87 cm
Now we can calculate the electric field strength at the point 4 m away from the center of the rod. Since the rod is made of an insulating material, the electric field outside the rod can be calculated using Coulomb's law:
E = k * (q / r^2)
where k is the electrostatic constant (k = 9 x 10^9 Nm^2/C^2), q is the charge, and r is the distance from the center of charge to the point where we want to calculate the electric field.
Converting the distance to meters:
r = 4 m
Plugging in the values into the formula:
E = (9 x 10^9 Nm^2/C^2) * (2q) / (4^2)
E = (9 x 10^9 Nm^2/C^2) * (2q) / 16
E = (9 x 10^9 Nm^2/C^2) * (2q) / 16
E = 0.1125 * (2q) N/C
Since the total charge on the rod is Q = -230 nC, we have:
-230 nC = q + 2q
-230 nC = 3q
Solving for q:
q = -230 nC / 3
q = -76.67 nC
Plugging this value back into the electric field equation:
E = 0.1125 * (2 * (-76.67 nC)) N/C
E = -0.1125 * 153.34 nC / C
E = -17.23 N/C
The electric field is a vector quantity, so its magnitude is always positive. Taking the absolute value:
|E| = 17.23 N/C
Converting this value to volts per meter (V/m):
1 V/m = 1 N/C
|E| = 17.23 V/m
Therefore, the strength of the rod's electric field at a point 4 m away from the rod's center along an axis perpendicular to the rod is approximately 17.23 V/m.
To learn more about electric field click here:
brainly.com/question/30544719
#SPJ11
Task: Solve the following problems. SHOW ALL THE POSSIBLE SOLUTIONS and BOX YOUR FINAL ANSWER. 1. The figure below shows four parallel plate capacitors: A, B, C, and D. Each capacitor carries the same charge q and has the same plate area A. As suggested by the figure, the plates of capacitors A and C are separated by a distance d while those of B and D are separated by a distance 2d. Capacitors A and B are maintained in vacuum while capacitors C and D contain dielectrics with constant k = 5. Arrange the capacitor in decreasing order of capacitance (e.g. A, B, C, and D) and explain briefly. (10pts) vacuum dielectric (K-5) D HA NI -2d- 20
The capacitors can be arranged in decreasing order of capacitance as follows: A, D, C, and B.
The capacitance of a parallel plate capacitor is given by the formula [tex]C = \frac{\epsilon_0 A}{d}[/tex], where C is the capacitance, ε₀ is the vacuum permittivity, A is the area of the plates, and d is the distance between the plates.
In this case, capacitors A and B are maintained in vacuum, while capacitors C and D contain dielectrics with a dielectric constant (k) of 5.
Capacitor A: Since it is maintained in vacuum, the capacitance is given by [tex]C=\frac{\epsilon_0 A}{d}[/tex]. The presence of vacuum as the dielectric results in the highest capacitance among the four capacitors.
Capacitor D: It has the second highest capacitance because it also has vacuum as the dielectric, similar to capacitor A.
Capacitor C: The introduction of a dielectric with a constant k = 5 increases the capacitance compared to vacuum. The capacitance is given by [tex]C=\frac{k \epsilon_0A}{d}[/tex]. Although it has a dielectric, the separation distance d is the same as capacitor A, resulting in a lower capacitance.
Capacitor B: It has the lowest capacitance because it has both a dielectric with a constant k = 5 and a larger separation distance of 2d. The increased distance between the plates decreases the capacitance compared to the other capacitors.
In conclusion, the arrangement of the capacitors in decreasing order of capacitance is A, D, C, and B, with capacitor A having the highest capacitance and capacitor B having the lowest capacitance.
Learn more about capacitors here: brainly.com/question/21851402
#SPJ11
Consider a sinusoidal wave, traveling along the positive direction of X axis, is represented by the wave function (x, t). Suppose that the wave has amplitude 2 m, wavelength 4r m, and
frequency 1 Hz.
(a) Find the speed, wave number, and angular frequency of this wave.
(b) If 4 (x = 0, t = 0) = 0, find all possible choices for 4 (x, t).
The wave function of a sinusoidal wave, moving in the positive direction of the X axis with amplitude of 2m, wavelength of 4r m, and frequency of 1 Hz is given by; 4(x,t) = 2 sin (kx - ωt)where;k = 2π/λ = 2π/4r = π/2 rad/mω = 2πf = 2π(1) = 2π rad/s(a) Wave speed = v = fλ = (1)(4) = 4m/s
Wave number = k = 2π/λ = 2π/4 = π/2 rad/m
Angular frequency = ω = 2πf = 2π(1) = 2π rad/s(b) Since 4(x,t) = 2 sin (kx - ωt)If 4 (x = 0, t = 0) = 0;
Then;0 = 2 sin (k0 - ω0) = 2 sin 0 = 0This means that the first maximum is at 2, the first minimum is at -2, and the zero point is at 0. Therefore, all possible choices for 4 (x, t) are:4 (x,t) = 2 sin (kx - ωt)4 (x,t) = 2 cos (kx - ωt)4 (x,t) = -2 sin (kx - ωt)4 (x,t) = -2 cos (kx - ωt)
To Know more about wave number here:
brainly.com/question/32242568
#SPJ11
A 4F capacitor is charged to 3V and is then connected to an ideal 1 inductor at t = 0. The resulting circuit acts an an electromagnetic oscillator (LC circuit). Use 3 for this problem. (a) What is the angular frequency of oscillation (W)? (b) At what time is the capacitor fully discharged for the second time? (c) What is the maximum energy stored in the inductor at any time?
The maximum energy stored in the inductor at any time is 18J.
(a) The formula for the angular frequency of oscillation (W) for an electromagnetic oscillator (LC circuit) is given by:
[tex]W = 1 / sqrt(LC)[/tex]
Given L = 1 and C = 4F,
we have:
W = 1 / sqrt(1 x 4)
W = 1 / 2rad/s
(b) The formula for the charge on a capacitor in an electromagnetic oscillator (LC circuit) at any time t is given by:
q(t) = Q0 cos(Wt)
and the formula for the voltage across the capacitor in an electromagnetic oscillator (LC circuit) at any time t is given by:
[tex]v(t) = V0 sin(Wt)[/tex]
At the point when the capacitor is fully discharged for the second time, the voltage across the capacitor will be zero (V0 sin(Wt) = 0).
Thus, sin(Wt) = 0, and Wt = nπ.
Since we are interested in the second time the capacitor is fully discharged, n = 2.
Therefore, Wt = 2π, and t = 2π / W
= 2π x 2 = 4s.
(c) The formula for the energy stored in an inductor in an electromagnetic oscillator (LC circuit) at any time t is given by: [tex]U(t) = (1/2)Li²(t)[/tex]
Since the capacitor is fully charged to 3V, we can calculate the initial charge on the capacitor as:
Q0 = CV0
= 4 x 3
= 12CAt
t = 0, the charge on the capacitor is Q0 cos(0) = Q0 = 12C, and the current in the inductor is zero.
Thus, the energy stored in the inductor at t = 0 is zero.
Since energy is conserved in an electromagnetic oscillator (LC circuit), the total energy stored in the circuit must remain constant.
Thus, the maximum energy stored in the inductor at any time is equal to the initial energy stored in the capacitor, which is given by:
(1/2)CV0²
= (1/2)(4)(3²)
= 18J
Therefore, the maximum energy stored in the inductor at any time is 18J.
To learn more about inductor visit;
https://brainly.com/question/31503384
#SPJ11
What is the magnetic flux, in Wb, for the following? A single loop of wire has perimeter (length) 1.0 m, and encloses an area of 0.0796 m2. It carries a current of 24 mA, and is placed in a magnetic field of 0.975 T so that the field is perpendicular to the plane containing the loop of wire.
The magnetic flux for the given configuration is approximately 0.07707 Weber (Wb).
The magnetic flux (Φ) is given by the formula:
Φ = B * A * cos(θ)
Where:
Φ is the magnetic flux in Weber (Wb),
B is the magnetic field strength in Tesla (T),
A is the area enclosed by the loop of wire in square meters (m²),
θ is the angle between the magnetic field and the normal to the plane of the loop.
In this case, the magnetic field is perpendicular to the plane of the loop, so θ = 0.
Therefore, the equation simplifies to:
Φ = B * A
Given:
B = 0.975 T (magnetic field strength)
A = 0.0796 m² (area enclosed by the loop)
Plugging in the values, we get:
Φ = 0.975 T * 0.0796 m² = 0.07707 Wb
Therefore, the magnetic flux for the given configuration is approximately 0.07707 Weber (Wb).
Learn more about magnetic flux from this link:
https://brainly.com/question/31870481
#SPJ11
A 0.40 kg mass is attached to a spring with a force constant of k-307 N/m, and the mass spring system is set into oscillation with an amplitude of A2.3 cm. Determine the following (a) mechanical energy of the system (b) maximum speed of the Oscillating mass m/s (c) magnitude of the maximum acceleration of the oscillating mass m/s?
The maximum speed of the oscillating mass is approximately 0.635 m/s. the magnitude of the maximum acceleration of the oscillating mass is approximately 18.71 m/s².
(a) To determine the mechanical energy of the system, we need to consider both the potential energy and the kinetic energy.
The potential energy (PE) of a mass-spring system is given by:
[tex]PE = (1/2) * k * A^2[/tex]
where:
k is the force constant of the spring,
A is the amplitude of the oscillation.
Substituting the given values:
k = 307 N/m
A = 2.3 cm = 0.023 m
[tex]PE = (1/2) * 307 N/m * (0.023 m)^2[/tex]
Calculating the value, we get:
[tex]PE ≈ 0.00258 J[/tex]
The kinetic energy (KE) of the system can be determined using the equation:
[tex]KE = (1/2) * m * v^2[/tex]
where:
m is the mass,
v is the velocity.
Since the mass is given as 0.40 kg, we can calculate the kinetic energy once we determine the maximum velocity (v).
(b) To find the maximum velocity of the oscillating mass, we can use the equation:
[tex]v = ω * A[/tex]
where:
ω is the angular frequency,
A is the amplitude of the oscillation.
The angular frequency (ω) can be calculated using the formula:
ω = √(k / m)
Substituting the given values:
k = 307 N/m
m = 0.40 kg
[tex]ω = √(307 N/m / 0.40 kg)[/tex]
Calculating the value, we get:
ω ≈ 27.62 rad/s
Now we can calculate the maximum velocity (v):
v = ω * A
Substituting the values:
v = 27.62 rad/s * 0.023 m
Calculating the value, we get:
v ≈ 0.635 m/s
Therefore, the maximum speed of the oscillating mass is approximately 0.635 m/s.
(c) The magnitude of the maximum acceleration of the oscillating mass can be determined using the equation:
[tex]a = ω^2 * A[/tex]
where:
ω is the angular frequency,
A is the amplitude of the oscillation.
Using the previously calculated value of ω ≈ 27.62 rad/s and the given value of A = 0.023 m, we can calculate the acceleration (a):
[tex]a = (27.62 rad/s)^2 * 0.023 m[/tex]
Calculating the value, we get:
[tex]a ≈ 18.71 m/s²[/tex]
Therefore, the magnitude of the maximum acceleration of the oscillating mass is approximately 18.71 m/s².
Learn more about mechanical energy from the given link
https://brainly.com/question/30403434
#SPJ11
At what separation is the electrostatic force between a+16−μC point charge and +70−μC point charge equal in magnitude to 4.6 N ? (in m)
The separation between the +16μC point charge and +70μC point charge, where the electrostatic force is equal in magnitude to 4.6N, is 0.0887m.
To find the separation between the point charges, we can use Coulomb's law. The formula for Coulomb's law is given as F = k (q1q2) / r² where, F is the electrostatic force, k is Coulomb's constant, q1 and q2 are the magnitudes of the charges, r is the distance between the two charges.
We are given that the electrostatic force between the +16μC point charge and +70μC point charge is equal to 4.6N. Therefore, we can write the equation as:
4.6 = k (16 × 10⁻⁶) (70 × 10⁻⁶) / r²
Simplifying the above equation, we get:
r = 0.0887 m.
Hence, the separation between the +16μC point charge and +70μC point charge, where the electrostatic force is equal in magnitude to 4.6N, is 0.0887m.
Learn more about Coulomb's law here:
https://brainly.com/question/506926
#SPJ11
cylinder from Heat Transfer) 2. Find the overall resistance per metre length for the following: α i =1500 W/m 2 K, α 0 =12X0 W/m 2 K, and α i =1500 W/m 2 K,α 0 =2YoW/m 2 K. Use 2in. standard type M copper tube dimensions, λ copper =399 W/mK. Compare the results.
The overall resistance per meter length for the given conditions can be calculated as follows:
For the first case (αi = 1500 W/m²K, αo = 120 W/m²K):
Overall resistance, R1 = (1 / αi) + (t / λ) + (1 / αo)
Where t is the thickness of the copper tube.
For the second case (αi = 1500 W/m²K, αo = 20 W/m²K):
Overall resistance, R2 = (1 / αi) + (t / λ) + (1 / αo)
To calculate the overall resistance per meter length, we consider the resistance to heat transfer at the inside surface of the tube, the resistance through the tube wall, and the resistance at the outside surface of the tube.
In both cases, we use the given values of αi (inside surface heat transfer coefficient), αo (outside surface heat transfer coefficient), and λ (thermal conductivity of copper) to calculate the individual resistances. The thickness of the copper tube, denoted as t, is also considered.
The overall resistance is obtained by summing up the individual resistances using the appropriate formula for each case.
By comparing the overall resistance per meter length for the two cases, we can assess the impact of the different values of αo. The comparison will provide insight into how the outside surface heat transfer coefficient affects the overall heat transfer characteristics of the system.
To learn more about resistance ,visit
brainly.com/question/17563681
#SPJ11
which group of the periodic table consists of elements that share similar properties and have 2 electrons in their outer shells
A. 1
B. 13
C. 14
D. 2
Answer: The correct answer is A.
Explanation:
Group 1 of the periodic table consists of elements that share similar properties and have 2 electrons in their outer shells. These elements are known as the alkali metals. They include elements such as lithium (Li), sodium (Na), potassium (K), and so on, all of which have a single electron in their outermost shell.
In a dc motor, __________ are used to connect the power source to the commutator.
In a DC motor, brushes are used to connect the power source to the commutator.
A DC motor is a device that converts electrical energy into mechanical energy. DC motors use the interaction between magnetic fields to convert electrical energy into mechanical energy. These are most often used in applications that require high torque and low speed, such as winches, cranes, and conveyor belts.
The speed of a DC motor can be adjusted by varying the current flowing through the motor. A DC motor operates on the principles of attraction and repulsion between magnetic fields.
to know more about DC motor here:
brainly.com/question/33280497
#SPJ11
The following energy storage system is used to store the power produced from the PV system during the daytime to be used during the nighttime for a total load of 2000 kWh during 10 hours. Given that: PV efficiency is 0.18, converter efficiency is 0.87, compressor isentropic efficiency is 0.85, average solar intensity during the day time for 8 hours is 500 W, Electrolyzer efficiency at standard pressure and temperature (1 bar and 25 oC) is 0.7, power output from the fuel cell is specified by: Pfuel cell=76.4 VH2-0.84 Where Pfuel cell is the fuel cell output power in W as DC VH2 is the volume flow rate of H2 in liter per minutes at standard conditions. The hydrogen is stored inside the tank during the day time at 100 bar and 25 oC. Calculate: (a) The minimum volume of hydrogen tank. (b) The average fuel cell efficiency. (c) The surface area of the PV system. (d) The heat dissipated from the intercooler. (e) The water flow rate inlet to the electrloyzer. (f) The overall system efficiency.
The given energy storage system requires several calculations to determine key parameters. These include the minimum volume of the hydrogen tank, average fuel cell efficiency, surface area of the PV system, heat dissipated from the intercooler, water flow rate to the electrolyzer, and overall system efficiency.
(a) To calculate the minimum volume of the hydrogen tank, we need to consider the energy requirement during the nighttime. The total load of 2000 kWh during 10 hours corresponds to an average power consumption of 2000 kWh / 10 hours = 200 kW.
Since the hydrogen is stored at 100 bar and 25 °C, we can use the ideal gas law to calculate the volume:
V = (m * R * T) / (P * MW)
Where V is the volume, m is the mass of hydrogen, R is the gas constant, T is the temperature in Kelvin, P is the pressure, and MW is the molecular weight of hydrogen.
Given that the hydrogen is stored at 100 bar (10^6 Pa), and assuming the molecular weight of hydrogen is 2 g/mol, we can calculate the mass of hydrogen required using the equation:
m = (E / (fuel cell efficiency * LHV)) * (1 / converter efficiency * PV efficiency * compressor efficiency * electrolyzer efficiency)
where E is the energy consumption during the nighttime (2000 kWh), LHV is the lower heating value of hydrogen (assuming 120 MJ/kg), and the efficiencies are given.
Substituting the values into the equations, we can determine the minimum volume of the hydrogen tank.
(b) The average fuel cell efficiency can be calculated by integrating the fuel cell power output equation over the volume flow rate of hydrogen. However, since the equation is given in terms of VH2 in liters per minute and the hydrogen storage volume is typically given in liters, we need to convert the volume flow rate to the total volume of hydrogen used during the nighttime.
(c) The surface area of the PV system can be calculated by dividing the power output of the PV system by the average solar intensity during the daytime.
(d) The heat dissipated from the intercooler can be calculated using the efficiency of the compressor and the power input to the compressor.
(e) The water flow rate inlet to the electrolyzer can be calculated based on the stoichiometric ratio of hydrogen and oxygen in water and the volume flow rate of hydrogen.
(f) The overall system efficiency can be calculated by dividing the total useful output energy by the total input energy, taking into account the losses in each component of the system.
To learn more about electrolyzer, click here: https://brainly.com/question/31870558
#SPJ11
Finnish saunas can reach temperatures as high as 130 - 140 degrees Celcius - which extreme sauna enthusiasts can tolerate in short bursts of 3 - 4 minutes. Calculate the heat required to convert a 0.8 kg block of ice, brought in from an outside temperature of -8 degrees Celcius, to steam at 104.0 degrees Celcius in the sauna. [The specific heat capacity of water vapour is 1.996 kJ/kg/K; see the lecture notes for the other specific heat capacities and specific latent heats].
To calculate heat required to convert a 0.8 kg block of ice to steam at 104.0 degrees Celsius in a sauna, we need to consider stages of phase change and specific heat capacities and specific latent heats involved.
First, we need to calculate the heat required to raise the temperature of the ice from -8 degrees Celsius to its melting point at 0 degrees Celsius. The specific heat capacity of ice is 2.09 kJ/kg/K. The equation for this heat transfer is:
Q1 = mass * specific heat capacity * temperature change
Q1 = 0.8 kg * 2.09 kJ/kg/K * (0 - (-8)) degrees Celsius. Next, we calculate the heat required to melt the ice at 0 degrees Celsius. The specific latent heat of fusion for ice is 334 kJ/kg. The equation for this heat transfer is:
Q2 = mass * specific latent heat
Q2 = 0.8 kg * 334 kJ/kg
After the ice has melted, we need to calculate the heat required to raise the temperature of the water from 0 degrees Celsius to 100 degrees Celsius. The specific heat capacity of water is 4.18 kJ/kg/K. The equation for this heat transfer is:
Q3 = mass * specific heat capacity * temperature change
Q3 = 0.8 kg * 4.18 kJ/kg/K * (100 - 0) degrees Celsius
Finally, we calculate the heat required to convert the water at 100 degrees Celsius to steam at 104.0 degrees Celsius. The specific latent heat of vaporization for water is 2260 kJ/kg. The equation for this heat transfer is:
Q4 = mass * specific latent heat
Q4 = 0.8 kg * 2260 kJ/kg
The total heat required is the sum of Q1, Q2, Q3, and Q4:
Total heat = Q1 + Q2 + Q3 + Q4
Calculating these values will give us the heat required to convert the ice block to steam in the sauna.
To learn more about specific latent heats click here : brainly.com/question/30460917
#SPJ11
7. How did Thomas Young's experiment support the wave model of light? K/U (5) w
By observing the interference pattern produced when light passed through two closely spaced slits, Young demonstrated that light exhibited characteristics of wave behavior such as diffraction and interference.
In Young's double-slit experiment, a beam of light was directed at a barrier with two closely spaced slits. Behind the barrier, a screen was placed to capture the light that passed through the slits. The resulting pattern on the screen showed alternating bright and dark regions known as interference fringes.
The key observation from this experiment was that the interference pattern could only be explained if light behaved as a wave. When two waves interact, they can either reinforce each other (constructive interference) or cancel each other out (destructive interference).
The interference pattern observed in Young's experiment could only be explained if the light waves were overlapping and interfering with each other, indicating their wave-like nature.
This experiment provided strong evidence against the prevailing particle theory of light and supported the wave model. It demonstrated that light could exhibit interference, diffraction, and other wave-like phenomena, which could not be explained by the particle theory.
Young's experiment was a milestone in the understanding of light and played a significant role in the development of the wave theory of light.
Learn more about interference here: brainly.com/question/23202500
#SPJ11
Predict how much torque is affecting this simple motor. The area inside the rectangle is 15 cm2, the current it carries is 9 A, the magnetic field has a magnitude of 20 * 10-3 T, and the angle between the area vector and the magnetic field is 1.0 radians.
The torque affecting the simple motor can be predicted as 6 * 10⁻⁷ m² * T * sin(1.0 radians).
The torque (τ) affecting the motor can be calculated using the formula:
τ = A * B * sin(θ)
where:
A is the area of the rectangle (15 cm²),
B is the magnitude of the magnetic field (20 * 10^-3 T),
θ is the angle between the area vector and the magnetic field (1.0 radians).
Substituting the given values into the formula, we have:
τ = 15 cm² * 20 * 10^-3 T * sin(1.0 radians)
To simplify the calculation, we convert the area from cm² to m²:
τ = (15 cm² * 10^-4 m²/cm²) * 20 * 10^-3 T * sin(1.0 radians)
τ = 3 * 10^-4 m² * 20 * 10^-3 T * sin(1.0 radians)
τ = 6 * 10^-7 m² * T * sin(1.0 radians)
To learn more about area -
brainly.com/question/29813972
#SPJ11
w = Yellow & blue light Glass Blue light (500 nm) and yellow light (600 nm) are incident on a slab of glass of thickness w = 12.0 cm, as shown in the figure. The incident beam makes an angle 0, = 45.0° with respect to the normal to the surface. In the glass, the index of refraction for the blue light is 1.565 and for the yellow light it is 1.518. The index of refraction of air is 1.000. 킄 Air Air B What distance d along the glass slab (side AB) separates the points at which the two rays emerge back into air? d = cm
(a) The distance (d) along the glass slab that separates the points at which the blue and yellow rays emerge back into air can be determined by considering the path difference between the two rays.
The path difference arises due to the difference in the indices of refraction for the two wavelengths of light and the angle of incidence.
(b) The path difference can be calculated using the formula Δd = (n_blue - n_yellow) × w × cos(θ), where n_blue and n_yellow are the indices of refraction for blue and yellow light respectively, w is the thickness of the glass slab, and θ is the angle of incidence.
Plugging in the given values of n_blue = 1.565, n_yellow = 1.518, w = 12.0 cm, and θ = 45.0°, we can calculate the path difference as Δd = (1.565 - 1.518) × 12.0 cm × cos(45.0°) ≈ 0.263 cm.
In summary, the distance (d) along the glass slab that separates the points at which the blue and yellow rays emerge back into air is approximately 0.263 cm. This calculation takes into account the path difference caused by the difference in the indices of refraction for the two wavelengths of light and the angle of incidence.
Learn more about rays here: brainly.com/question/29861000
#SPJ11
Which of these statements best explains why a telescope enables us to see details of a distant object such as the Moon or a planet more clearly?
The image formed by the telescope is larger than the object.
The image formed by the telescope extends a larger angle at the eye than the object does.
The telescope can also collect radio waves that sharpen the visual image
Justify your answer to the previous question. choose 1
Interference
Light Gathering Power
Rayleigh Criterion
The statement that best explains why a telescope enables us to see details of a distant object such as the Moon or a planet more clearly is: The image formed by the telescope is larger than the object.
Telescope enables us to see details of a distant object such as the Moon or a planet more clearly because the image formed by the telescope is larger than the object. It is because the image is formed by the convergence of light rays from the object at a single point and at the same distance from the lens of the telescope. This forms an enlarged and more detailed view of the object, which helps in seeing it more clearly. This is how a telescope magnifies the image of a distant object.
The other options do not explain why a telescope enables us to see details of a distant object such as the Moon or a planet more clearly. The statement "The image formed by the telescope extends a larger angle at the eye than the object does" is incorrect because a telescope does not extend the angle at the eye. The statement "The telescope can also collect radio waves that sharpen the visual image" is also incorrect because telescopes cannot collect radio waves, radio telescopes are specifically designed to do this.
Justification: The correct answer for the previous question is Light Gathering Power. Light gathering power is a measure of the ability of a telescope to collect light. The larger the telescope's light gathering power, the more light it can collect, which enables it to form a brighter and more detailed image of the object being observed. This is important because the more light the telescope collects, the greater the amount of detail that can be seen.
To know more about telescope visit :
https://brainly.com/question/19349900
#SPJ11
What happens to the path of the refracted ray in the cube as O, increases?
R Describe the path of the beam as it exits the cube relative to the direction of the originally incident ray. You may need to place a piece of paper behind the cube to locate the path of the ray after it refracts at
the second interface when exiting the cube.)
C Circle one: Going from a rare to dense medium, does the ray refract toward or away from the normal?
Circle one: Traveling from a dense to rare medium, does it refract toward or away from the normal?
The answer to the first circle is "toward," and the answer to the second circle is "away."
As the angle of incidence, O increases, the path of the refracted ray in the cube moves farther away from the normal. When the angle of incidence is increased gradually, the refracted beam moves gradually toward the edge of the cube, and at the same time, its angle of refraction changes.As the light ray exits the cube, the path of the beam is parallel to the direction of the originally incident ray. In the case of the refraction of light, when a light ray moves from a rare (less dense) medium to a denser medium, it will be refracted towards the normal, i.e. towards the perpendicular. However, if the light ray travels from a dense to a rare (less dense) medium, it will be refracted away from the normal.Thus, the answer to the first circle is "toward," and the answer to the second circle is "away."Learn more about the angle of incidence:
brainly.com/question/30402542
#SPJ11
A circular wire loop has a 10 cm radius and carries one half Ampere of current (clockwise, seen from above). A. Find the size and direction of the magnetic field at the center of the loop. B. Find the magnitude and direction of the magnetic field along the axis of the loop at a point two meters above the loop. Hint: treat the loop as a dipole.
A. The magnetic field at the center of the loop is 2π × 10^(-6) T, directed perpendicular to the plane of the loop, B. The magnetic field along the axis of the loop, at a point two meters above the loop, is approximately 1.25 × 10^(-9) T, directed downward.
A. To find the magnetic field at the center of the loop, we can use Ampere's Law. According to Ampere's Law, the magnetic field at the center of a circular loop is given by the formula:
B = (μ₀ * I) / (2 * R),
where B is the magnetic field, μ₀ is the permeability of free space (4π × 10^(-7) T·m/A), I is the current, and R is the radius of the loop.
Plugging in the values, we have:
B = (4π × 10^(-7) T·m/A) * (0.5 A) / (2 * 0.1 m) B = 2π × 10^(-6) T.
The magnetic field is directed perpendicular to the plane of the loop (towards or away from you), as determined by the right-hand rule.
B. To find the magnetic field along the axis of the loop, we treat the loop as a magnetic dipole. The magnetic field at a point on the axis of a magnetic dipole is given by the formula:
B = (μ₀ * m) / (4π * r³),
where B is the magnetic field, μ₀ is the permeability of free space, m is the magnetic dipole moment, and r is the distance from the center of the dipole to the point on the axis.
The magnetic dipole moment is given by:
m = (I * A),
where I is the current and A is the area of the loop.
Plugging in the values, we have:
m = (0.5 A) * (π * (0.1 m)²) = 0.05π A·m².
Now, let's calculate the magnetic field at a point two meters above the loop (r = 2 m):
B = (4π × 10^(-7) T·m/A) * (0.05π A·m²) / (4π * (2 m)³) B ≈ 1.25 × 10^(-9) T.
The magnetic field is directed downward along the axis of the loop.
Hence, A. The magnetic field at the center of the loop is 2π × 10^(-6) T, directed perpendicular to the plane of the loop. B. The magnetic field along the axis of the loop, at a point two meters above the loop, is approximately 1.25 × 10^(-9) T, directed downward.
Learn more about magnetic field from the link
https://brainly.com/question/14411049
#SPJ11
q1
why c
1. A car drives north for one hour at \( 80 \mathrm{~km} / \mathrm{h} \). It then continues north, traveıing ave What is its average velocity (in \( \mathrm{km} / \mathrm{h} \) )? A) 140 north (8) 65
The average velocity that was travelled is given as 60 km
How to solve for the average velocityThe speed is given as 80 km in 1 hour
The formula for velocity is given as total distance / total time
The total distance that was covered is given as
100 km + 80 km
= 180 km
Next we will have to solve for the total time
The total time is given as
1 hour + 2 hours
= 3 hours
Next we have to apply the velocity formula
= 180 / 3
= 60 km
Read more on average velocity here https://brainly.com/question/24739297
#SPJ4
Question
A car drives north for one hour at 80 km It then continues north, traveıing average at 100 km for 2 hours. What is its average velocity ? A) 140 north (b) 65 c 60 d 50
Sketch a ray diagram for each case showing the 3 important rays:
A converging lens has a focal length of 14.0 cm. Locate the images for object distances of (a) 40.0 cm, (b) 14.0 cm, and (c) 9.0 cm.
a. For an object distance of 40.0 cm, the image formed by a converging lens with a focal length of 14.0 cm is real, inverted, and located beyond the focal point. The magnification can be determined using the lens formula and is less than 1.
b. For an object distance of 14.0 cm, the image formed by the lens is at infinity, resulting in a real, inverted, and highly magnified image.
c. For an object distance of 9.0 cm, the image formed by the lens is virtual, upright, and located on the same side as the object. The magnification is greater than 1.
a. When the object distance is 40.0 cm, the image formed by the converging lens is real, inverted, and located beyond the focal point. The magnification (m) can be determined using the lens formula:
1/f = 1/v - 1/u,
where f is the focal length, v is the image distance, and u is the object distance. By substituting the given values, we can solve for v and calculate the magnification.
b. For an object distance of 14.0 cm, the image formed by the lens is at infinity, resulting in a real, inverted, and highly magnified image. This occurs when the object is placed at the focal point of the lens. The magnification in this case can be calculated using the formula:
m = -v/u,
where v is the image distance and u is the object distance.
c. When the object distance is 9.0 cm, the image formed by the lens is virtual, upright, and located on the same side as the object. This occurs when the object is placed inside the focal point of the lens. The magnification can be calculated using the same formula as in case a. However, the magnification will be greater than 1, indicating an upright and enlarged image.
Learn more about magnification here:
brainly.com/question/21370207
#SPJ4
Pkg 0.21 7. A car of 1200 kg is travelling at 20 m/s when it slams on the brakes. a. How much kinetic energy does the car have before it hits the brakes? b. Where does this energy go when the driver brakes to a stop? c. What is the work done by the car's brakes? d. If the car brakes over a distance of 50 m before coming to rest, what is the force of friction provided by the brakes on the car? (ans: 4800 N)
To find the kinetic energy of the car before it slams on the brakes, the formula used is Kinetic Energy = 1/2(mv²). The mass of the car is 1200 kg and the speed at which the car is traveling is 20 m/s.So the Kinetic energy = 1/2 x 1200 kg x (20 m/s)² = 240000 J.b. When the driver applies the brakes and the car comes to a stop, the kinetic energy of the car is transformed into heat energy.
The heat energy is generated due to the friction between the brakes and the car’s wheels. This means the kinetic energy of the car is dissipated in the form of heat energy generated by the brakes and the car’s wheels.c. The work done by the car’s brakes is equal to the amount of kinetic energy dissipated when the car stops. So the work done by the car’s brakes can be calculated as 240000 J.d. The force due to inertia is equal to mass x acceleration, where the mass of the car is 1200 kg and the acceleration is equal to the rate at which the car slows down, which can be calculated as (0 – 20 m/s) / 50 m = -0.4 m/s². The force due to inertia can be calculated as 1200 kg x (-0.4 m/s²) = -480 N.
Therefore, the force of friction provided by the brakes is Frictional Force = Force Applied – Force Due to Inertia = 0 – (-480 N) = 4800 N.
To know more about kinetic energy visit:
https://brainly.com/question/999862
#SPJ11
An ideal neon sign transformer provides 9080 V at 51.0 mA with an input voltage of 110 V. Calculate the transformer's
input power and current.
An ideal neon sign transformer provides 9080 V at 51.0 mA with an input voltage of 110 V, the transformer's input power is approximately 464.28 W and the input current is approximately 4.22 A.
We can use the following calculation to compute the transformer's input power:
Input Power (P) = Input Voltage (V) * Input Current (I)
Here, it is given that:
Input Voltage (V) = 110 V
Input Current (I) = ?
Input Current (I) = Output Power (P) / Output Voltage (V)
Given:
Output Power (P) = 9080 V * 51.0 mA = 464.28 W (converting mA to A)
Output Voltage (V) = 9080 V
Now,
Input Current (I) = 464.28 W / 110 V ≈ 4.22 A
Thus, the transformer's input power is approximately 464.28 W and the input current is approximately 4.22 A.
For more details regarding transformer, visit:
https://brainly.com/question/15200241
#SPJ4
A capacitor with initial charge qo is discharged through a resistor. (a) In terms of the time constant t, how long is required for the capacitor to lose the first one-third of its charge? XT (b) How long is required for the capacitor to lose the first two-thirds of its charge?
(a) The time required for the capacitor to lose the first one-third of its charge is given by t1 = t * ln(3), and (b) the time required to lose the first two-thirds of its charge is t2 = t * ln(3^2)
(a) To calculate the time required for the capacitor to lose the first one-third of its charge, we can use the formula:t1 = t * ln(3)
Where t1 represents the time required, t is the time constant, and ln denotes the natural logarithm. This formula is derived from the exponential decay behavior of a charging or discharging capacitor.
(b) Similarly, to find the time required for the capacitor to lose the first two-thirds of its charge, we can use the formula:
t2 = t * ln(3^2)
Here, t2 represents the time required to lose the first two-thirds of the charge.
(a) The time required for the capacitor to lose the first one-third of its charge is given by t1 = t * ln(3), and (b) the time required to lose the first two-thirds of its charge is t2 = t * ln(3^2). These formulas utilize the natural logarithm and the time constant to calculate the desired time durations.
Learn more about capacitor click here:
brainly.com/question/31627158
#SPJ11
Four equal positive point charges, each of charge 8.6 °C, are at the corners of a square of side 8.6 cm. What charge should be placed at the center of the square so that all charges are at equilibrium? Express your answer using two significant figures. How much voltage must be used to accelerate a proton (radius 1.2 x10^-15m) so that it has sufficient energy to just penetrate a silicon nucleus? A silicon -15 nucleus has a charge of +14e, and its radius is about 3.6 x10-15 m. Assume the potential is that for point charges. Express your answer using two significant figures.
An 8.6 °C charge should be placed at the center of a square of side 8.6 cm so that all charges are at equilibrium. The voltage that must be used to accelerate a proton is 4.6 x 10^6V.
Four equal positive point charges are at the corners of a square of side 8.6 cm. The charges have a magnitude of 8.6 x 10^-6C each. We are to find out the charge that should be placed at the center of the square so that all charges are at equilibrium. Since the charges are positive, the center charge must be negative and equal to the sum of the corner charges. Thus, the center charge is -34.4 µC.
A proton with a radius of 1.2 x 10^-15m is accelerated by voltage V so that it has enough energy to penetrate a silicon nucleus. The nucleus has a charge of +14e, where e is the fundamental charge, and a radius of 3.6 x 10^-15m. The potential at the surface of the nucleus is V = kq/r, where k is the Coulomb constant, q is the charge of the nucleus, and r is the radius of the nucleus.
Using the potential energy expression, 1/2 mv^2 = qV, we get V = mv^2/2q, where m is the mass of the proton. Setting the potential of the proton equal to the potential of the nucleus, we get 4.6 x 10^6V. Therefore, the voltage that must be used to accelerate a proton is 4.6 x 10^6V.
Learn more about charges:
https://brainly.com/question/24206363
#SPJ11
A baseball is thrown from the outfield to home plate. Let's say the outfielder and catcher are 46 m horizontally apart, and the ball leaves the outfielders hand at a height of 2.14 m. (Assume no air resistance) Part A) If it takes 2.29 s for the ball to get from fielder to catcher, what was the magnitude of the velocity of the ball in the "x" right before the catcher gets the ball? Part B) If the catcher catches the ball at a height of 2.29 m, find the vertical velocity the ball had when it left the fielders hand. Part C) At what angle did the fielder throw the ball with respect to the ground? angle = unit
We know the vertical and horizontal distances the ball travelled, so we can calculate the angle θ.tan θ = h / dθ = tan⁻¹(h / d)θ = tan⁻¹(2.14 m / 46 m)θ = 2.65°The angle the fielder threw the ball with respect to the ground is 2.65° (rounded to two decimal places).
Part A) To find the velocity of the ball in the "x" direction right before the catcher gets the ball, we need to use the formula:v
= d / t Where:v is the velocity of the ballad is the distance the ball travelst is the time it takes to travel the distance In this case, we know the distance and time, so we can calculate the velocity:v
= d / t
= 46 m / 2.29 s
= 20.09 m/s
So the magnitude of the velocity of the ball in the "x" right before the catcher gets the ball is 20.09 m/s.Part B) To find the vertical velocity the ball had when it left the fielder's hand, we can use the formula:v²
= u² + 2gh where:v is the final velocity of the ballu is the initial velocity of the ballg is the acceleration due to gravity h is the vertical distance the ball travelst is the time it takes to travel the distance We know the initial and final heights of the ball, the acceleration due to gravity, and the time it took to travel the distance. So we can calculate the initial velocity of the ball. The final height of the ball is 2.29 m and the initial height of the ball is 2.14 m. The acceleration due to gravity is -9.8 m/s² (taking downwards as negative) and the time it took to travel the distance is 2.29 s.v²
= u² + 2ghu²
= v² - 2ghu²
= (0 m/s)² - 2(-9.8 m/s²)(2.29 m - 2.14 m)u²
= 19.6 m²/s² (2.9 m)u
= ±11.35 m/s
The initial velocity of the ball can be either upward or downward. Since the ball was thrown from the outfielder to the catcher, the initial velocity of the ball was upward. Therefore, the vertical velocity the ball had when it left the fielder's hand was 11.35 m/s upward.Part C) To find the angle the fielder threw the ball with respect to the ground, we can use the formula:tan θ
= h / d where:θ is the angle the fielder threw the ball with respect to the ground h is the vertical distance the ball travelled is the horizontal distance the ball traveled In this case. We know the vertical and horizontal distances the ball travelled, so we can calculate the angle θ.tan θ
= h / dθ
= tan⁻¹(h / d)θ
= tan⁻¹(2.14 m / 46 m)θ
= 2.65°
The angle the fielder threw the ball with respect to the ground is 2.65° (rounded to two decimal places).
To know more about horizontal visit:
https://brainly.com/question/29019854
#SPJ11
A crown weighing 8.30 N is suspended underwater from a string. The tension in the string is measured to be 7.81 N. Calculate the density of the crown either in gm/cc or kg/m3.
To calculate the density of the crown, we can use the concept of buoyancy. When an object is submerged in a fluid, the buoyant force exerted on the object is equal to the weight of the fluid displaced by the object.
In this case, the tension in the string is equal to the buoyant force acting on the crown, and the weight of the crown is given. By applying the equation for density, density = mass/volume, we can determine the density of the crown.
The buoyant force acting on the crown is equal to the tension in the string, which is measured to be 7.81 N. The weight of the crown is given as 8.30 N. According to Archimedes' principle, the buoyant force is equal to the weight of the fluid displaced by the crown. Therefore, the buoyant force can be considered as the difference between the weight of the fluid displaced and the weight of the crown.
The weight of the fluid displaced by the crown is equal to the weight of the crown when it is fully submerged. Thus, the weight of the fluid displaced is 8.30 N. Since the buoyant force is equal to the weight of the fluid displaced, it is also 8.30 N.
The density of an object is given by the equation density = mass/volume. In this case, the mass of the crown can be calculated using the weight of the crown and the acceleration due to gravity. The mass is given by mass = weight/gravity, where gravity is approximately 9.8 m/s^2. Therefore, the mass of the crown is 8.30 N / 9.8 m/s^2.
Finally, we can calculate the density of the crown by dividing the mass of the crown by its volume. The volume of the crown is equal to the volume of the fluid displaced, which is given by the formula volume = weight of the fluid displaced / density of the fluid. The density of water is approximately 1000 kg/m^3.
By substituting the values into the equation density = mass/volume, we can determine the density of the crown in either gm/cc or kg/m^3.
To learn more about density click here:
brainly.com/question/31977852
#SPJ11
A proton (denoted by p) moves with velocity v upward through a uniform magnetic field B that points into the plane. What will be the direction of the resulting magnetic force on the proton? to the right to the left downward out of the plane
The direction of the resulting magnetic force on a proton, when it moves with velocity v upward through a uniform magnetic field B that points into the plane, is to the right. The correct option is - to the right.
To determine the direction of the resulting magnetic force on a proton moving through a magnetic field, we can use the right-hand rule.
When the right-hand rule is applied to a positive charge moving through a magnetic field, such as a proton, the resulting force is perpendicular to both the velocity vector (v) and the magnetic field vector (B).
In this case, the proton is moving upward (opposite to the force of gravity) and the magnetic field is pointing into the plane.
To apply the right-hand rule, we can point the index finger of our right hand in the direction of the velocity vector (upward), and the middle finger in the direction of the magnetic field vector (into the plane).
The resulting force vector (thumb) will be perpendicular to both the velocity and the magnetic field, which means it will be pointing to the right. Therefore, the direction of the resulting magnetic force on the proton will be to the right.
So, the correct option is - to the right.
Learn more about magnetic fields here:
https://brainly.com/question/7645789
#SPJ11
Nuclear radiation exists in several different forms, three of which are listed here. 1. alpha 2. beta 3. gamma 2. When these forms of decay are all dangerous. When arranged in order of greatest ability to penetrate human tissue to least ability to penetrate human tissue, the order is
When arranged in order of greatest ability to penetrate human tissue to least ability, the order of nuclear radiation forms is as follows: 1. gamma radiation, 2. beta radiation, and 3. alpha radiation.
Gamma radiation is the most penetrating form of nuclear radiation. It consists of high-energy photons and can easily pass through most materials, including human tissue. Due to its high penetrating power, gamma radiation poses significant risks to living organisms.
Beta radiation, which includes beta particles (high-speed electrons) and positrons, has intermediate penetrating power. It can penetrate through materials to a certain extent, but its ability to penetrate human tissue is less compared to gamma radiation.
Alpha radiation, on the other hand, consists of alpha particles, which are composed of two protons and two neutrons. Alpha particles have the least penetrating power among the three forms of radiation. They can be stopped by a sheet of paper or a few centimeters of air, and they cannot penetrate human tissue easily.
To know more about nuclear radiation click here: brainly.com/question/28231494
#SPJ11
Tanya jumps off of a raft to the left with both initially at rest. Tanya has a mass of 65 kg and the mass of the raft is 120 kg. After she jumps off the raft, she has a velocity of 1.5 m/s left after 2 seconds. a) With what force does Tanya apply to the raft? [ ] b) What is raft's velocity after 2 seconds?
Tanya applies a force of approximately 48.75 N to the raft. The velocity of the raft after Tanya jumps off is approximately 0.8125 m/s to the left.
a) To find the force with which Tanya applies to the raft, we can use the principle of conservation of momentum. The initial momentum of the system (Tanya + raft) is zero since they are initially at rest together. After Tanya jumps off with a velocity of 1.5 m/s to the left, the momentum of the system should still be zero.
Let's denote the velocity of the raft as v. The momentum of Tanya is given by:
p of Tanya = mass of Tanya × velocity of Tanya
= 65 kg × (-1.5 m/s)
= -97.5 kg·m/s (to the right)
The momentum of the raft is given by:
p_ of raft = mass of raft × velocity of raft = 120 kg × v
Since the total momentum of the system is conserved, we have:
p of Tanya + p of raft = 0
-97.5 kg·m/s + 120 kg * v = 0
Solving for v, we have:
v = 97.5 kg·m/s / 120 kg
= 0.8125 m/s
b) The force with which Tanya applies to the raft can be determined using Newton's second law, which states that force is equal to the rate of change of momentum.
The rate of change of momentum of the raft can be calculated as:
Change in momentum = final momentum - initial momentum
= mass of raft * final velocity - mass of raft * initial velocity
= 120 kg * (0.8125 m/s) - 120 kg * 0 m/s
= 97.5 kg·m/s
Since the change in momentum occurs over a time interval of 2 seconds, we can calculate the force using the formula:
Force = Change in momentum / time
= 97.5 kg·m/s / 2 s
= 48.75 N
Learn more about velocity -
brainly.com/question/80295
#SPJ11
