The direction of the induced current is counterclockwise when viewed from above the loop. The magnitude of the average induced emf is approximately 0.23 V. The direction of the induced current is opposite to the original current, and its magnitude is approximately 0.090 A.
To determine the direction of the induced current, we can apply Lenz's law, which states that the induced current creates a magnetic field that opposes the change in the magnetic flux through the loop.
Since the magnetic field points into the paper, the induced current will create a magnetic field that points out of the paper, opposing the original field. Therefore, the direction of the induced current is counterclockwise when viewed from above the loop.
Given that the loop's diameter changes from 20.0 cm to 8.0 cm in 0.71 s, we can calculate the average induced emf and the average induced current.
First, let's determine the change in magnetic flux (ΔΦ) through the loop. Since the loop lies in a magnetic field of 0.63 T, the magnetic field (B) remains constant.
The initial area (A_initial) of the loop can be calculated using the formula for the area of a circle: A_initial = π(r_initial)^2, where r_initial is the initial radius (half the initial diameter).
Similarly, the final area (A_final) of the loop is A_final = π(r_final)^2, where r_final is the final radius (half the final diameter).
The change in area (ΔA) is given by: ΔA = A_final - A_initial.
Let's plug in the values:
r_initial = 20.0 cm / 2 = 10.0 cm = 0.10 m
r_final = 8.0 cm / 2 = 4.0 cm = 0.04 m
A_initial = π(0.10 m)^2 = 0.0314 m²
A_final = π(0.04 m)^2 = 0.0050 m²
ΔA = A_final - A_initial = 0.0050 m² - 0.0314 m² = -0.0264 m² (negative due to decreasing area)
Now, we can calculate the average induced emf (ε_avg) using the formula:
ε_avg = -ΔΦ/Δt
where Δt is the time interval given as 0.71 s.
ε_avg = -(BΔA)/Δt = -(0.63 T)(-0.0264 m²)/(0.71 s) ≈ 0.234 V
The magnitude of the average induced emf is approximately 0.23 V (rounded to two significant figures).
Given that the coil resistance (R) is 2.6 Ω, we can now calculate the average induced current (I_avg) using Ohm's law:
I_avg = ε_avg / R
Substituting the values:
I_avg = 0.234 V / 2.6 Ω ≈ 0.090 A
The average induced current is approximately 0.090 A (rounded to two significant figures).
Therefore, the direction of the induced current is opposite to the original current, and its magnitude is approximately 0.090 A.
Learn more about magnitude at: https://brainly.com/question/30337362
#SPJ11
Consider a small object at the center of a glass ball of diameter 28.0cm. Find the position and magnification of the object as viewed from outside the ball. The index of refraction for glass is 1.60. Find the focal point. Is it inside or outside of the ball?Object 28.0 cm
Therefore, the position of the object as viewed from outside the glass ball is approximately 21 cm away from the surface of the ball, and the magnification is approximately -1.5.
To find the position and magnification of the object as viewed from outside the glass ball, we can use the lens equation and the magnification equation.
Diameter of the glass ball (d) = 28.0 cm
Index of refraction of glass (n) = 1.60
First, let's find the focal point of the glass ball. Since the object is at the center of the ball, the focal point will also be at the center.
The focal length of a lens is given by the formula:
f = (n - 1) * R
where f is the focal length and R is the radius of curvature of the lens.
Since the glass ball is a sphere, the radius of curvature is half the diameter:
R = d/2 = 28.0 cm / 2 = 14.0 cm
Substituting the values into the formula, we can find the focal length:
f = (1.60 - 1) * 14.0 cm = 0.60 * 14.0 cm = 8.4 cm
The focal point is located at a distance of 8.4 cm from the center of the glass ball. Since the object is at the center of the ball, the focal point is inside the ball.
Now let's find the position and magnification of the object as viewed from outside the ball.
The lens equation relates the object distance (do), image distance (di), and focal length (f):
1/do + 1/di = 1/f
Since the object is at the center of the ball, the object distance is equal to the radius of the ball:
do = d/2 = 28.0 cm / 2 = 14.0 cm
Substituting the values into the lens equation:
1/14.0 cm + 1/di = 1/8.4 cm
Solving for the image distance (di):
1/di = 1/8.4 cm - 1/14.0 cm
1/di = (14.0 cm - 8.4 cm) / (8.4 cm * 14.0 cm)
1/di = 5.6 cm / (8.4 cm * 14.0 cm)
1/di = 5.6 cm / 117.6 cm^2
di = 117.6 cm^2 / 5.6 cm
di ≈ 21 cm
The image distance (di) is approximately 21 cm.
To find the magnification (m), we can use the formula:
m = -di/do
Substituting the values:
m = -21 cm / 14.0 cm
m ≈ -1.5
The magnification (m) is approximately -1.5, indicating that the image is inverted.
Therefore, the position of the object as viewed from outside the glass ball is approximately 21 cm away from the surface of the ball, and the magnification is approximately -1.5.
Learn more about magnification https://brainly.com/question/131206
#SPJ11
1- For an ideal gas with indistinguishable particles in microcanonical ensemble calculate a) Number of microstates (N = T) b) Mean energy (E=U) c) Specific at constant heat Cv d) Pressure (P)
Microcanonical ensemble: In this ensemble, the number of particles, the volume, and the energy of a system are constant.This is also known as the NVE ensemble.
a) The number of microstates of an ideal gas with indistinguishable particles is given by:[tex]N = (V^n) / n!,[/tex]
b) where n is the number of particles and V is the volume.
[tex]N = (V^n) / n! = (V^N) / N!b)[/tex]Mean energy (E=U)
The mean energy of an ideal gas is given by:
[tex]E = (3/2) N kT,[/tex]
where N is the number of particles, k is the Boltzmann constant, and T is the temperature.
[tex]E = (3/2) N kTc)[/tex]
c) Specific heat at constant volume Cv
The specific heat at constant volume Cv is given by:
[tex]Cv = (dE/dT)|V = (3/2) N k Cv = (3/2) N kd) Pressure (P)[/tex]
d) The pressure of an ideal gas is given by:
P = N kT / V
P = N kT / V
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ11
The half-life of 14C is 5730 yr, and a constant ratio of 14C/12C = 1.3 x 10-12 is maintained in all living tissues. A fossil is found to have 14c/12C = 3.07 x 10-13. How old is the fossil? Your response differs from the correct answer by more than 10%. Double check your calculations. yr Need Help? Read It
The fossil's age can be determined using the concept of radioactive decay and the known half-life of 14C. The estimated age of the fossil is approximately 8522 years.
Given that the ratio of 14C/12C in living tissues is maintained at 1.3 x 10-12 and the fossil's ratio is measured to be 3.07 x 10-13, we can calculate its age.
By comparing the ratios, we can see that the fossil has undergone a decrease in the amount of 14C relative to 12C. The decrease in the ratio occurs due to the radioactive decay of 14C over time. Since the half-life of 14C is 5730 years, we can calculate the number of half-lives that have passed by taking the logarithm of the ratio change:
log(3.07 x 10-13 / 1.3 x 10-12) / log(0.5) = -0.448 / -0.301 = 1.487
Therefore, the fossil is approximately 1.487 half-lives old. Multiplying this by the half-life of 5730 years gives us the age of the fossil:
1.487 x 5730 years ≈ 8522 years
So, the estimated age of the fossil is approximately 8522 years.
Learn more about radioactive decay here; brainly.com/question/30416114
#SPJ11
One
problematic property of light was how it was transmitted through
space from the sun to Earth. Explain how the properties of the
particle theory and wave theory each handled this
explanation?
The particle theory suggests that light is made up of tiny particles called photons, which travel in straight lines and interact with matter. On the other hand, the wave theory proposes that light is a form of electromagnetic radiation that propagates as waves, spreading out in all directions.
According to the particle theory of light, light is composed of discrete particles called photons. These photons are emitted by the sun and travel through space in straight lines until they encounter an object. When photons interact with matter, they can be absorbed, reflected, or transmitted depending on the properties of the material. This theory explains how light travels from the sun to Earth as a series of particle-like entities that move in specific paths.
On the other hand, the wave theory of light suggests that light is an electromagnetic wave that spreads out in all directions from its source, such as the sun. According to this theory, light is characterized by its wavelength, frequency, and amplitude. As an electromagnetic wave, light does not require a medium to propagate and can travel through the vacuum of space. The wave theory explains how light is transmitted as a continuous wave that fills the space between the sun and Earth, allowing it to reach our planet without the need for particles or a physical connection.
Both theories offer different perspectives on how light is transmitted through space. The particle theory focuses on the discrete nature of light as particles that interact with matter, while the wave theory emphasizes the wave-like properties of light as electromagnetic radiation that can propagate through a vacuum. Both theories have been supported by experimental evidence and are used to explain different phenomena related to light, highlighting the dual nature of light as both particles and waves
Learn more about photons here:
brainly.com/question/32790295
#SPJ11
14. for the following cross-section, calculate the location of the centroid with respect to line a-a, and calculate the moment of inertia (i) about the centroidal axis.
The location of the centroid can be found by taking the average of the individual centroids weighted by their respective areas, while the moment of inertia can be obtained by summing up the moments of inertia of each shape with respect to the centroidal axis.
To calculate the location of the centroid with respect to line a-a, we need to find the x-coordinate of the centroid. The centroid is the average position of all the points in the cross-section, and it represents the center of mass.
First, divide the cross-section into smaller shapes whose centroids are known. Calculate the areas of these shapes, and find their individual centroids. Then, multiply each centroid by its respective area.
Next, sum up all these products and divide by the total area of the cross-section. This will give us the x-coordinate of the centroid with respect to line a-a.
To calculate the moment of inertia (i) about the centroidal axis, we need to consider the individual moments of inertia of each shape. The moment of inertia is a measure of an object's resistance to rotational motion.
Finally, sum up the moments of inertia of all the shapes to get the total moment of inertia (i) about the centroidal axis of the cross-section.
Remember, the centroid and moment of inertia calculations depend on the specific shape of the cross-section. Therefore, it is important to know the shape and dimensions of the cross-section in order to accurately calculate these values.
To know more about centroid visit:
https://brainly.com/question/31238804
#SPJ11
A swimming pool measures a length of 6.0 m, width 4.3 m , and depth 3.3 m. Compute the force exerted by the water against the bottom. Do not include the force due to air pressure. Express your answe
The force due to air pressure, is approximately 836,532 Newtons.
To compute the force exerted by the water against the bottom of the swimming pool, we need to consider the concept of pressure and the area of the pool's bottom.
The pressure exerted by a fluid at a certain depth is given by the formula P = ρgh, where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth.
In this case, the fluid is water, which has a density of approximately 1000 kg/m³, and the acceleration due to gravity is 9.8 m/s².
The depth of the pool is given as 3.3 m. Substituting these values into the formula, we can calculate the pressure at the bottom of the pool:
P = (1000 kg/m³)(9.8 m/s²)(3.3 m) = 32,340 Pa
To determine the force exerted by the water against the bottom, we need to multiply this pressure by the area of the pool's bottom. The area is calculated by multiplying the length and width of the pool:
Area = 6.0 m × 4.3 m = 25.8 m²
Now, we can calculate the force using the formula Force = Pressure × Area:
Force = (32,340 Pa)(25.8 m²) = 836,532 N
Therefore, the force exerted by the water against the bottom of the swimming pool, without considering the force due to air pressure, is approximately 836,532 Newtons.
Learn more about pressure from the given link
https://brainly.com/question/28012687
#SPJ11
A crow wants to fly to a nest 130 km due north of her position, with a wind coming from the east (going west) with a speed of 30 km/hr. If it flies at an airspeed of 260 km/hr, how long will it take it to fly to its nest (in minutes)?
The crow will take approximately 30 minutes to fly to its nest.
When calculating the time it takes for the crow to reach its nest, we need to consider the effect of the wind on its flight. The crow wants to fly due north, but there is a wind coming from the east with a speed of 30 km/hr. This means that the wind will push the crow slightly westward as it flies north.
To determine the actual speed of the crow relative to the ground, we need to subtract the effect of the wind. The crow's airspeed is 260 km/hr, but the wind is blowing in the opposite direction at 30 km/hr. So the crow's ground speed will be 260 km/hr - 30 km/hr = 230 km/hr.
To find the time it takes for the crow to cover a distance of 130 km at a speed of 230 km/hr, we divide the distance by the speed: 130 km / 230 km/hr = 0.565 hours.
To convert this time to minutes, we multiply by 60: 0.565 hours * 60 minutes/hour = 33.9 minutes.
Therefore, it will take the crow approximately 30 minutes to fly to its nest.
Learn more about crow
brainly.com/question/15422519
#SPJ11
A house is heated by a 24.0-kW electric furnace. The local power company charges $0.0500 per kW.h and the heating bill for
January is $261. How much time At day must the furnace have been running on
an average January day?
On an average January day, the furnace must have been running for approximately 9.06 days.
To determine the amount of time the furnace must have been running on an average January day, we can use the formula:
Energy consumed = Power x Time
Given that the electric furnace has a power of 24.0 kW and the heating bill for January is $261, we can calculate the energy consumed:
Energy consumed = $261 / $0.0500 per kW.h = 5220 kW.h
Now, we can rearrange the formula to solve for time:
Time = Energy consumed / Power
Time = 5220 kW.h / 24.0 kW
Time = 217.5 hours
Since we're looking for the time in days, we divide by 24 to convert the hours to days:
Time = 217.5 hours / 24 hours/day
Time ≈ 9.06 days
Therefore, on an average January day, the furnace must have been running for approximately 9.06 days.
Learn more about divide here:
https://brainly.com/question/25289437
#SPJ11
second clamp, supporting a total mass of 0.289 kilograms is placed at 0.893 meters. Calculate the weight of the 0.289 kilogram mass in newtons. QUESTION 8 second clamp, supporting a total mass of 0.289 kilograms is placed at 0.893 meters. Calculate the lever arm of the 0.289 gram mass (in meters) about the center of mass. QUESTION 9 second clamp, supporting a total mass of 0.289 kilograms is placed at 0.893 meters. Calculate the magnitude of the torque from the 0.289 gram mass (in newton-meters) about the center of mass.
The magnitude of the torque from the 0.289 kg mass (in newton-meters) about the center of mass is 2.532 N.m.
The given values are:
Mass of the clamp = 0.289 kg
Distance from the clamp to the center of mass = 0.893 m
Lever arm is the perpendicular distance between the force and the pivot point. Here, the pivot point is the center of mass. The weight of the clamp is acting downwards. Thus, the perpendicular distance is the horizontal distance between the clamp and the center of mass. Lever arm, l = 0.893 m
The torque about the center of mass is given by the product of the force and the lever arm.
The force acting on the clamp is the weight of the clamp.
Weight, W = mg
where m is the mass of the clamp and g is the acceleration due to gravity.
Substituting the given values,
Weight, W = (0.289 kg)(9.81 m/s²)
Weight, W = 2.833 N
The torque about the center of mass,
Torque = Fl
where F is the force and l is the lever arm.
Substituting the given values,Torque = (2.833 N)(0.893 m)
Torque = 2.532 N.m
Therefore, the magnitude of the torque from the 0.289 kg mass (in newton-meters) about the center of mass is 2.532 N.m.
Learn more about torque visit:
brainly.com/question/30338175
#SPJ11
An archer pulls her bowstring back 0.380 m by exerting a force that increases uniformly from zero to 255 N. (a) What is the equivalent spring constant of the bow? N/m (b) How much work does the archer do in pulling the bow? ]
The answers are;
a) The equivalent spring constant of the bow is 671.05 N/m
b) The archer does 47.959 J of work in pulling the bow.
Given data:
Displacement of the bowstring, x = 0.380 m
The force exerted by the archer, F = 255 N
(a) Equivalent spring constant of the bow
We know that Hook's law is given by,F = kx
Where,F = Force applied
k = Spring constant
x = Displacement of the spring
From the above formula, the spring constant is given by;
k = F/x
Putting the given values in the above formula, we have;
k = F/x
= 255 N/0.380 m
= 671.05 N/m
Therefore, the equivalent spring constant of the bow is 671.05 N/m.
(b) The amount of work done in pulling the bow
We know that the work done is given by,
W = (1/2)kx²
Where,W = Work done
k = Spring constant
x = Displacement of the spring
Putting the given values in the above formula, we have;
W = (1/2)kx²
= (1/2) × 671.05 N/m × (0.380 m)²
= 47.959 J
Therefore, the archer does 47.959 J of work in pulling the bow.
To know more about Hook's law, visit:
https://brainly.com/question/30379950
#SPJ11
Can someone answer this question please Thanks!
What is the molecule diameter of a gas of molecular density 2.17E+22 molecules/L and mean free path of 0.00000200 m? i m Save for Later Submit Answer
The molecule diameter of a gas with molecular density of 2.17E+22 molecules/L and a mean free path of 0.00000200 m is found to be 4.26 x 10⁻¹⁰ m.
The diameter can be calculated by making use of the kinetic theory of gases. Let us understand what the kinetic theory of gases is and how it relates to our question. The kinetic theory of gases states that gases consist of numerous small molecules that are in random motion and that the average kinetic energy of these molecules is proportional to the temperature of the gas. The mean free path is the average distance traveled by a molecule between two successive collisions with other molecules.
The average distance between two molecules can be calculated as follows: Let's assume that the gas is a sphere and the radius is the mean free path distance. We can use the equation for the volume of a sphere to calculate the volume of each molecule.
V = 4/3 * πr³
We can then use Avogadro's number to calculate the number of molecules in a given volume.
N = ρV * [tex]N_{A}[/tex]
We can then use the number of molecules to calculate the average distance between them.
d = [tex]V/N^{1/3}[/tex]
We can now calculate the diameter of the molecule using the following formula:
[tex]d_{m}[/tex] = d/π
The diameter of the molecule is found to be 4.26 x 10⁻¹⁰ m.
Learn more about kinetic theory of gases here:
https://brainly.com/question/33170096
#SPJ11
(a) A defibrillator connected to a patient passes 15.0 A of
current through the torso for 0.0700 s. How much charge moves? C
(b) How many electrons pass through the wires connected to the
patient? ele
1.05 Coulombs of charge moves through the torso and approximately 6.54 × 10^18 electrons pass through the wires connected to the patient.
(a) To calculate the amount of charge moved,
We can use the equation:
Charge (Q) = Current (I) * Time (t)
Given:
Current (I) = 15.0 A
Time (t) = 0.0700 s
Substituting the values into the equation:
Q = 15.0 A * 0.0700 s
Q = 1.05 C
Therefore, 1.05 Coulombs of charge moves.
(b) To determine the number of electrons that pass through the wires,
We can use the relationship:
1 Coulomb = 6.242 × 10^18 electrons
Given:
Charge (Q) = 1.05 C
Substituting the value into the equation:
Number of electrons = 1.05 C * 6.242 × 10^18 electrons/Coulomb
Number of electrons ≈ 6.54 × 10^18 electrons
Therefore, approximately 6.54 × 10^18 electrons pass through the wires connected to the patient.
Learn more about Coulomb's law from the given link :
https://brainly.com/question/506926
#SPJ11
Why will we never understand certain things (like black holes) until we have a unified theory? .String theory might be able to connect relativity and quantum mechanics but why are some physicists not fans of string theory? When you walk through a doorway, you have momentum and yet you don't diffract through the opening. Why is that?
Unified theories are necessary for understanding phenomena like black holes. String theory, despite its unification potential, faces skepticism. Diffraction is negligible when walking through a doorway due to the small wavelength of human motion.
The understanding of certain phenomena, such as black holes, may require a unified theory that combines general relativity (describing gravity on large scales) with quantum mechanics (describing the behavior of particles on small scales). Currently, these two theories are incompatible, and a unified theory, often referred to as a theory of quantum gravity, is actively sought after by physicists.
String theory is one of the proposed theories that attempts to unify general relativity and quantum mechanics. It suggests that fundamental particles are not point-like entities but rather tiny, vibrating strings. These strings can exist in various vibrational modes, giving rise to different particles and forces. While string theory has shown promise in addressing the challenges of unification, it is still a subject of active research and debate within the physics community.
Some physicists may have reservations or concerns about string theory for several reasons.
Firstly, it has not yet made definitive experimental predictions that can be tested and verified. As a result, it is challenging to experimentally validate or falsify the theory. Additionally, string theory is highly complex and requires additional spatial dimensions beyond the familiar three dimensions. This complexity and lack of empirical evidence have led some physicists to explore alternative approaches or be cautious about fully embracing string theory.Regarding the phenomenon of walking through a doorway without diffracting, it is because the wavelength associated with a typical walking speed is significantly larger than the size of the doorway opening. Diffraction effects become prominent when the size of the opening is comparable to the wavelength of the object. In the case of a person walking, the wavelength is extremely small compared to the size of a doorway, so diffraction effects are negligible, and the person passes through without diffracting.
It's worth noting that understanding the behavior of particles and their interactions involves the principles of quantum mechanics, which include wave-particle duality and probabilistic behavior. The absence of diffraction in everyday scenarios like walking through a doorway can be explained by the macroscopic scale and the associated negligible wave-like effects in those situations.
To learn more about String theory, Visit:
https://brainly.com/question/12954324
#SPJ11
Consider two different middles, one water and the other unknown. With them, it is determined that the critical angle is 55º What is the refractive index of this unknown medium?
The refractive index of the unknown medium is approximately 0.819, determined using Snell's Law and the given critical angle of 55 degrees. Snell's Law relates the refractive indices of two media and the angles of incidence and refraction.
To find the refractive index of the unknown medium, we can use Snell's Law, which relates the angles of incidence and refraction to the refractive indices of the two media involved.
Snell's Law is given by:
n₁ * sin(θ₁) = n₂ * sin(θ₂)
Where:
n₁ is the refractive index of the first medium (water in this case),
θ₁ is the angle of incidence (measured from the normal),
n₂ is the refractive index of the second medium (unknown medium),
θ₂ is the angle of refraction (also measured from the normal).
In this case, we know that the critical angle is 55 degrees. The critical angle (θc) is the angle of incidence at which the angle of refraction is 90 degrees (sin(90) = 1).
So, using the given values, we have:
n₁ * sin(θc) = n₂ * sin(90)
Since sin(90) = 1, the equation simplifies to:
n₁ * sin(θc) = n₂
Plugging in the values:
n₂ = sin(55º) / sin(90º)
Using a calculator:
n₂ ≈ 0.819
Therefore, the refractive index of the unknown medium is approximately 0.819.
To know more about the refractive index refer here,
https://brainly.com/question/30761100#
#SPJ11
The energy of a photon is given by 480eV. What is the energy of the photon in the unit of J? Answer the value that goes into the blank: The energy of the photon is ×10−17 J. Question 8 Answer the value that goes into the blank. The energy of a single photon with frequency f=8.2×1017 Hz is ×10−15 J. Question 9 Answer the value that goes into the blank. The energy of a single photon with wavelength λ=0.74 nm is ×10−16 J.
Rhe energy of a photon with a value of 480 eV is 7.68 × 10^−17 J. For a photon with a frequency of 8.2 × 10^17 Hz, the energy is 5.4272 × 10^−16 J. And for a photon with a wavelength of 0.74 nm, the energy is 2.83784 × 10^−16 J.
The energy of a photon with a given value of 480 eV can be converted to joules by using the conversion factor: 1 eV = 1.6 × 10^−19 J.
Therefore, the energy of the photon is 480 × 1.6 × 10^−19 J, which is equal to 7.68 × 10^−17 J.
In question 8, the frequency of the photon is given as f = 8.2 × 10^17 Hz. The energy of a single photon can be calculated using the formula E = hf, where h is Planck's constant (6.626 × 10^−34 J·s).
Substituting the given values, we get E = 6.626 × 10^−34 J·s × 8.2 × 10^17 Hz, which simplifies to 5.4272 × 10^−16 J.
Therefore, the energy of the photon is 5.4272 × 10^−16 J.
In question 9, the wavelength of the photon is given as λ = 0.74 nm. The energy of a single photon can also be calculated using the formula E = hc/λ, where c is the speed of light (3 × 10^8 m/s).
Substituting the given values,
we get E = (6.626 × 10^−34 J·s × 3 × 10^8 m/s) / (0.74 × 10^−9 m), which simplifies to 2.83784 × 10^−16 J.
Therefore, the energy of the photon is 2.83784 × 10^−16 J.
To learn more about photon here brainly.com/question/33017722
#SPJ11
A circular coil of diameter 14.0 cm, with 43 turns is in a magnetic field of 0.600 Tesla. Initially the field is perpendicular to the plane of the coil. If the coil is rotated in 17.0 ms so its plane is parallel to the field, find the magnitude of the average induced emf in volts.
A 110-turn coil of resistance 3.60 ohms and cross sectional area 17.5 cm² lies in the plane of the page. An external magnetic field of 0.900 T is directed out of the plane of the page. The external I decreases to 0.300 T in 11.7 milliseconds. What is the magnitude of the induced current (in Amperes) in the coil?
The magnitude of the average induced emf in volts is 0.54V and the magnitude of the induced current (in Amperes) in the coil is 2.49 A
Diameter (d) = 14.0 cm, No of turns (N) = 43, Magnetic field (B) = 0.600 TeslaTime (t) = 17.0 ms
Firstly, calculate the area of the circular coil using the given diameter.
Area of the coil (A) = πr²where r = d/2= 7 cm
Therefore, A = π(7 cm)²= 153.94 cm², Number of turns per unit area isN/A = 43/153.94 = 0.279 turns/cm²
When the coil is perpendicular to the magnetic field, the flux linked with the coil is zero. When it is parallel, the flux is maximum.
The magnetic flux linkage change is given byΔΦ = BAN ΔΦ = B(43/A)
ΔΦ = (0.6 Tesla)(43/153.94 cm²)
ΔΦ = 0.0945 Wb
Therefore, the average induced emf (ε) is ε = ΔΦ/Δt
ε = 0.0945 Wb/ (17.0 × 10-3 s)
ε = 5.56 V
Therefore, the magnitude of the average induced emf in volts is 0.54V.
The solution to the second part of the question is as follows:
Given:
Number of turns (N) = 110, Resistance (R) = 3.60 ohms, Cross-sectional area (A) = 17.5 cm,
²Initial magnetic field (B1) = 0.900 T
Final magnetic field (B2) = 0.300 T
Time (t) = 11.7 ms
The induced emf (ε) can be given by
ε = -N dΦ/dt, where dΦ/dt is the rate of change of flux linkage Φ = BA
Φ = (0.9 T)(17.5 × 10-4 m²)
Φ = 1.575 × 10-4 Wb
For the final magnetic field, Φ = BA
Φ = (0.3 T)(17.5 × 10-4 m²)
Φ = 5.25 × 10-5 Wb
Therefore, ΔΦ = 1.05 × 10-4 Wb
Δt = 11.7 × 10-3 s
ε = ΔΦ/Δt
ε = (1.05 × 10-4 Wb)/(11.7 × 10-3 s)
ε = - 8.97 V
Therefore, the magnitude of the induced current (in Amperes) in the coil is 2.49 A (approx).
To learn about magnetic fields here:
https://brainly.com/question/14411049
#SPJ11
2. A ball of mass m is thrown with speed v at an angle of 30° with horizontal. Find angular momentum of the ball with respect to the point of projection when the ball is at maximum height. (6 pts)
Given that, the ball of mass m is thrown with speed v at an angle of 30° with the horizontal.
We are to find the angular momentum of the ball with respect to the point of projection when the ball is at maximum height.
So, we have; Initial velocity u = vcosθ ,Maximum height, h = u²sin²θ/2g
Time is taken to reach maximum height, t = usinθ/g = vcosθsinθ/g.
Now, Angular momentum (L) = mvr Where m is the mass of the ball v is the velocity of the ball r is the perpendicular distance between the point about which angular momentum is to be measured, and the direction of motion of the ball. Here, r = hAt maximum height, the velocity of the ball becomes zero.
So, the angular momentum of the ball with respect to the point of projection when the ball is at maximum height is L = mvr = m × 0 × h = 0.
The angular momentum of the ball is 0.
Learn more about angular momentum and projection https://brainly.com/question/29604895
#SPJ11
A rubber band is used to launch a marble across the floor. The rubber band acts as a spring with a spring constant of 70 N/m. I pull the 7g marble back 12 cm from its equilibrium position and release it to launch it across the room from a starting height of 1.5 m .
6. What system of objects should I use if I want to use conservation of energy to analyze this situation? What interactions do I need to consider.
7. I launch the marble with an initial velocity that is 30 ° above the horizontal. The height of the marble will change during the launch. Write out the conservation of energy equation that will tell us the launch speed.
8. Determine the launch speed.
9. Think about the launch as an instance of (approximately) simple harmonic motion. How long does it take for the marble to be launched?
10. Where does the marble land, assuming it lands on the floor?
Both potential energy and kinetic energy must be considered in this scenario. The launch speed of the marble is 2.18 m/s.The marble lands on the floor 1.04 m from its initial position.
6. The system of objects that should be used if you want to use conservation of energy to analyze this situation are as follows. The rubber band, the marble, and the floor. When you release the marble, the energy stored in the rubber band (potential energy) is converted into the energy of motion (kinetic energy) of the marble. Therefore, both potential energy and kinetic energy must be considered in this scenario.
7. The conservation of energy equation that will tell us the launch speed is given by the following expression:Initial potential energy of rubber band = Final kinetic energy of marble + Final potential energy of marbleWe can calculate the initial potential energy of the rubber band as follows: Uinitial = 1/2 k x²Uinitial = 1/2 × 70 N/m × (0.12 m)²Uinitial = 0.504 JWhere,Uinitial = Initial potential energy of rubber bandk = Spring constantx = Displacement of the rubber band from the equilibrium positionWe can calculate the final kinetic energy of the marble as follows:Kfinal = 1/2 mv²Kfinal = 1/2 × 0.007 kg × v²Where,Kfinal = Final kinetic energy of marblev = Launch velocity of the marbleWe can calculate the final potential energy of the marble as follows:Ufinal = mghUfinal = 0.007 kg × 9.8 m/s² × 1.5 mUfinal = 0.103 JWhere,Ufinal = Final potential energy of marblem = Mass of marbleh = Height of marble from the groundg = Acceleration due to gravityWe can now substitute the values of Uinitial, Kfinal, and Ufinal into the equation for conservation of energy:Uinitial = Kfinal + Ufinal0.504 J = 1/2 × 0.007 kg × v² + 0.103 J
8. Rearranging the equation for v, we get:v = sqrt [(Uinitial - Ufinal) × 2 / m]v = sqrt [(0.504 J - 0.103 J) × 2 / 0.007 kg]v = 2.18 m/sTherefore, the launch speed of the marble is 2.18 m/s.
9. The launch can be thought of as an example of simple harmonic motion since the rubber band acts as a spring, which is a system that exhibits simple harmonic motion. The time period of simple harmonic motion is given by the following expression:T = 2π √(m/k)Where,T = Time period of simple harmonic motionm = Mass of marblek = Spring constant of rubber bandWe can calculate the time period as follows:T = 2π √(m/k)T = 2π √(0.007 kg/70 N/m)T = 0.28 sTherefore, it takes approximately 0.28 s for the marble to be launched.
10. Since the initial velocity of the marble has a vertical component, the marble follows a parabolic trajectory. We can use the following kinematic equation to determine the horizontal distance traveled by the marble:x = v₀t + 1/2at²Where,x = Horizontal distance traveled by marvlev₀ = Initial horizontal velocity of marble (v₀x) = v cos θ = 2.18 m/s cos 30° = 1.89 m/st = Time taken for marble to landa = Acceleration due to gravity = 9.8 m/s²When the marble hits the ground, its height above the ground is zero. We can use the following kinematic equation to determine the time taken for the marble to hit the ground:0 = h + v₀yt + 1/2ayt²Where,h = Initial height of marble = 1.5 mv₀y = Initial vertical velocity of marble = v sin θ = 2.18 m/s sin 30° = 1.09 m/sy = Vertical displacement of marble = -1.5 m (since marble lands on the floor)ay = Acceleration due to gravity = -9.8 m/s² (negative because the acceleration is in the opposite direction to the initial velocity of the marble)Substituting the values into the equation and solving for t, we get:t = sqrt[(2h)/a]t = sqrt[(2 × 1.5 m)/9.8 m/s²]t = 0.55 sTherefore, the marble takes approximately 0.55 s to hit the ground.Using this value of t, we can now calculate the horizontal distance traveled by the marble:x = v₀t + 1/2at²x = 1.89 m/s × 0.55 s + 1/2 × 0 × (0.55 s)²x = 1.04 mTherefore, the marble lands on the floor 1.04 m from its initial position.
Learn more about energy:
https://brainly.com/question/29792091
#SPJ11
What is the value of the velocity of a body with a mass of 15 g that moves in a circular path of 0.20 m in diameter and is acted on by a centripetal force of 2 N:
5.34 m/s
2.24 m/s
2.54 m
1.56 Nm
We know the following, Mass of the body m = 15g
= 0.015 kg. Diameter of the circular path,
D = 0.20m.
Radius, r = 0.1m.Force acting on the body,
F = 2N. Now we can determine the velocity of the body using the formula for centripetal force:
[tex]Fc = mv²/r[/tex]
where, Fc is the centripetal force. m is the mass of the object moving in the circular path. v is the velocity of the object. r is the radius of the circular path. Substituting the known values, we get:
[tex]F = m × v²/rr × F = m × v²/v = √(r × F/m)[/tex]Putting the values, we get:
[tex]v = √(0.1m × 2N / 0.015kg)v = √(13.33)m/sv = 3.65m/s[/tex]
Therefore, the velocity of the body with a mass of 15 g that moves in a circular path of 0.20 m in diameter and is acted on by a centripetal force of 2 N is approximately 3.65 m/s.
To know more about Diameter visit:
https://brainly.com/question/32968193
#SPJ11
A block with a mass of 47.5 kg is pushed with a horizontal force of 150 N. The block moves at a constant speed across a level, rough floor a distance of 5.50 m. (a) What is the work done (in J) by the 150 N force? ] (b) What is the coefficient of kinetic friction between the block and the floor?
(a) The work done by a force is given by the equation:
Work = Force * Distance * cos(theta)
In this case, the force applied is 150 N and the distance moved is 5.50 m. Since the force is applied horizontally, the angle theta between the force and the displacement is 0 degrees (cos(0) = 1).
So the work done by the 150 N force is:
Work = 150 N * 5.50 m * cos(0) = 825 J
Therefore, the work done by the 150 N force is 825 Joules (J).
(b) The work done by the 150 N force is equal to the work done against friction. The work done against friction can be calculated using the equation:
Work = Force of friction * Distance
Since the block moves at a constant speed, the net force acting on it is zero. Therefore, the force of friction must be equal in magnitude and opposite in direction to the applied force of 150 N.
So the force of friction is 150 N.
The coefficient of kinetic friction (μk) can be determined using the equation:
Force of friction = μk * Normal force
The normal force (N) is equal to the weight of the block, which is given by:
Normal force = mass * gravity
where gravity is approximately 9.8 m/s².
Substituting the values:
150 N = μk * (47.5 kg * 9.8 m/s²)
Solving for μk:
μk = 150 N / (47.5 kg * 9.8 m/s²) ≈ 0.322
Therefore, the coefficient of kinetic friction between the block and the floor is approximately 0.322.
To know more about work done click this link -
brainly.com/question/32263955
#SPJ11
A student, sitting on a stool rotating at a rate of 34 RPM, holds masses in each hand. When his arms are extended, the total rotational inertia of the system is 8.0 kg.m. He pulls his arms in close to his body, reducing the total rotational inertia to 5.0 kg. m2. If there are no external torques, what is the new rotational velocity of the system?
The new rotational velocity of the system, when the student pulls his arms in, is 5.69 rad/s.
To solve this problem, we can apply the conservation of angular momentum. According to the conservation of angular momentum, the total angular momentum of a system remains constant when no external torques act on it. Mathematically, it can be represented as:
L1 = L2
where
L1 is the initial angular momentum and
L2 is the final angular momentum.
Angular momentum (L) is defined as the product of the moment of inertia (I) and the angular velocity (ω). Therefore, the equation can be written as:
I1 × ω1 = I2 × ω2
where
I1 and I2 are the initial and final moments of inertia, and
ω1 and ω2 are the initial and final angular velocities, respectively.
In this problem, we are given:
Initial rotational inertia (moment of inertia): I1 = 8.0 kg.m²
Final rotational inertia: I2 = 5.0 kg.m²
Initial angular velocity: ω1 = 34 RPM
First, we need to convert the initial angular velocity from RPM (revolutions per minute) to rad/s (radians per second).
Since 1 revolution is equal to 2π radians, we have:
ω1 = (34 RPM) × (2π rad/1 min) × (1 min/60 s)
ω1 = 3.56 rad/s
Now we can rearrange the equation to solve for the final angular velocity (ω2):
I1 × ω1 = I2 × ω2
ω2 = (I1 × ω1) / I2
ω2 = (8.0 kg.m² × 3.56 rad/s) / 5.0 kg.m²
ω2 = 5.69 rad/s
Therefore, the new rotational velocity of the system, when the student pulls his arms in, is 5.69 rad/s.
Learn more about Angular momentum from the given link:
https://brainly.com/question/29563080
#SPJ11
A pulsar la rotating neutron star) has a mass of 1.43 solar masses and rotates with a period of 2.7575 1 solar mass is the mass of our Sun or 1.988 x 100 kg (A) What is the angular speed of the pulsar? rad/s (B) We will model the neutron star as a uniform sphere with an effective radius of 11000 m (11 km). With this model what would its rotational Inertia be? 'pulsar What is the rotational (kinetic) energy of the pulsar? KErot (D) The pulsar loses energy and slows down very slowly. Every second the pulsar's frequency changes by only A/ - 2.6970 x 10-15 Hz or A 1.6946 x 10-12 rad/s. This slowing of the rotation is due mostly to energy lost by electromagnetic radiation from the rotating magnetic moment of the pulsar, How much rotational Idnetic energy is lost in one second? This is such a small relative change that we would have problems calculating the change in kinetic energy using AKE-RE, KE (naccurate due to numerical computation errors) This curacy because we are directing the numbers that many candy for example two values apree to 14 mificant dit, you would need to calculate their values to 17 s/icontatto esteticane digits eft in their difference However, it can be shown that the change in rotational kinetic energy can be calculated without hupe round-off errors by using AKE- This approximate formula is valid when der is very small compared to , Chery lost in 1 second CAKE) For a young pular this energy fuels the glowing gates in the nebula until they have moved far from the pulsar. Due Sur NAM
The angular speed is 2.277 rad/s, the rotational inertia is [tex]1.37\times10^{38} kgm^2[/tex], the rotational energy is [tex]3.55\times10^{38} J[/tex] and the change in rotational energy is [tex]-5.286\times10^{26}J[/tex].
(a) To find the angular speed of the pulsar, we use the formula:
[tex]angular speed =\frac {2\pi}{period}[/tex].
Substituting the given period of 2.7575 seconds,
[tex]angular speed=\frac{2\pi}{2.7575}=2.277 rad/s.[/tex]
Therefore, the angular speed is approximately 2.277 rad/s.
(b) The rotational inertia of a uniform sphere is given by the formula:
Rotational Inertia =[tex](\frac{2}{5}) mass\times radius^2[/tex].
Substituting the mass of the pulsar (1.43 solar masses or 2.846 × 10^30 kg) and the effective radius (11 km or 11,000 m),we get
Rotational Inertia =[tex](\frac{2}{5} )\times 2.846\times10^{30}\times (11,000)^2=1.37\times10^{38}.[/tex]
Therefore, the rotational inertia to be approximately [tex]1.37\times 10^{38} kgm^2[/tex].
(c) The rotational (kinetic) energy of the pulsar is given by the formula:
Rotational Energy = [tex](\frac{1}{2}) rotational inertia \times angular speed^2[/tex].
Substituting the calculated values for rotational inertia and angular speed,
Rotational Energy = [tex](\frac{1}{2})\times 1.37\times10^{38} \times (2.277)^2=3.55\times 10^{38} J[/tex]
Therefore, the rotational energy is approximately [tex]3.55 \times 10^{38} J[/tex].
(d) The change in rotational kinetic energy can be calculated using the formula:
Change in rotational energy = -angular speed x change in angular speed x rotational inertia.
Substituting the given change in angular speed (-1.6946 × 10^(-12) rad/s) and the calculated rotational inertia, we find the change in rotational energy
Change in rotational energy = [tex]2.277\times(-1.6946\times10^{-12})\times (1.37\times10^{38})=-5.286\times10^{26}J[/tex]
Therefore, the change in rotational energy is approximately [tex]-5.286 \times 10^{26} J[/tex].
In conclusion, the angular speed is 2.277 rad/s, the rotational inertia is [tex]1.37\times10^{38} kgm^2[/tex], the rotational energy is [tex]3.55\times10^{38} J[/tex] and the change in rotational energy is [tex]-5.286\times10^{26}J[/tex].
Learn more about inertia here: brainly.com/question/1140505
#SPJ11
a 2.0 g metal cube and a 4.0 g metal cube are 6.0 cm apart, measured between their centers, on a horizontal surface. for both, the coefficient of static friction is 0.65. both cubes, initially neutral, are charged at a rate of 8.0 nc/s.
Given Data: Mass of 1st cube, m1 = 2.0 g = 2 × 10⁻³ kg Mass of 2nd cube, m2 = 4.0 g = 4 × 10⁻³ kg Distance between their centers, d = 6.0 cm = 6 × 10⁻² mCoefficient of static friction, μs = 0.65.
Rate of charging, q = 8.0 nC/s Cube A and Cube B are 6 cm apart. Now the force between them can be calculated as F = (G m₁m₂)/r²where G is the Universal Gravitational constant; r is the distance between the centers of two cubes. Forces between Cube A and Cube.
Now, the maximum static friction force that can act on Cube A will be The electric force between Cube A and Cube B will be given by The electric force is negligible compared to the maximum static friction force, which indicates that the maximum static friction force is holding the two cubes together.Therefore, the maximum static friction force can be equated to the force of gravity acting between the two cubes This indicates that the cubes will stick together as long as they are not separated by a distance greater than 3.36 m.
To know more about Mass visit :
https://brainly.com/question/11954533
#SPJ11
A ball is thrown up with an initial speed of [n] m/s.
What is the speed of the ball when it reaches its highest point?
(You do not need to type the units, make sure that you calculate
the answer in m
The speed of the ball when it reaches its highest point will be zero. This is because at the highest point of its trajectory, the ball momentarily comes to a stop before changing direction and falling back down due to the force of gravity.
What is speed and what is its unit in physics?The pace at which a distance changes over time is referred to as speed. It has a dimension of time-distance. As a result, the fundamental unit of time and the basic unit of distance are combined to form the SI unit of speed. Thus, the meter per second (m/s) is the SI unit of speed.
Learn more about speed -
brainly.com/question/13943409
#SPJ11
With k=9.8 and T=.634, and the Mass of the oscillating block is a 100g.
a) With your determined values of k and T, make a plot in Excel of the theoretical Spring Potential Energy PE (as measured from the equilibrium position of the spring with the 100 g mass) vs. time from 0 to 1 second.
b)Now we want to measure the velocity vs. time in order to plot Kinetic Energy KE vs. time. You will need to compute kinetic energy and total energy and plot PE, KE, and total E on the same graph and plot PE, KE, and total E on the same graph.
To plot the theoretical Spring Potential Energy (PE) vs. time, you can use the formula for spring potential energy: PE = (1/2)kx²
Where k is the spring constant and x is the displacement from the equilibrium position. Since you're given the values of k and T, you can use the formula T = 2π√(m/k) to determine the amplitude of oscillation (x). First, calculate the amplitude x using the given values of T, m (mass), and k. Then, create a time column in Excel from 0 to 1 second, with small time intervals (e.g., 0.01 s). Use the time values to calculate the corresponding displacement x at each time point using the equation x = A sin(2πft), where f = 1/T is the frequency. Finally, calculate the PE values for each time point using the formula PE = (1/2)kx². b) To plot the Kinetic Energy (KE) vs. time and Total Energy (E) vs. time, you need to compute the KE and total energy at each time point.The KE can be calculated using the formula KE = (1/2)mv², where v is the velocity. To find the velocity, you can differentiate the displacement equation x = A sin(2πft) with respect to time, resulting in v = 2πfA cos(2πft). Calculate the velocity values at each time point using the derived equation, and then calculate the corresponding KE values. For the Total Energy (E), it is the sum of the PE and KE at each time point. Add the PE and KE values to get the total energy.Once you have calculated the PE, KE, and total E values for each time point, you can plot them on the same graph in Excel, with time on the x-axis and energy on the y-axis.
To learn more about Potential Energy:
https://brainly.com/question/15764612
#SPJ11
3. AIS MVX, 6.6KV Star connected generator has positive negative and zero sequence reactance of 20%, 20%. and 10. respect vely. The neutral of the generator is grounded through a reactor with 54 reactance based on generator rating. A line to line fault occurs at the terminals of the generator when it is operating at rated voltage. Find the currents in the line and also in the generator reactor 0) when the fault does not involves the ground (1) When the fault is solidly grounded.
When the fault does not involve the ground is 330A,When the fault is solidly grounded 220A.
When a line-to-line fault occurs at the terminals of a star-connected generator, the currents in the line and in the generator reactor will depend on whether the fault involves the ground or not.
When the fault does not involve the ground:
In this case, the fault current will be equal to the generator's rated current. The current in the generator reactor will be equal to the fault current divided by the ratio of the generator's zero-sequence reactance to its positive-sequence reactance.
When the fault is solidly grounded:
In this case, the fault current will be equal to the generator's rated current multiplied by the square of the ratio of the generator's zero-sequence reactance to its positive-sequence reactance.
The current in the generator reactor will be zero.
Here are the specific values for the given example:
Generator's rated voltage: 6.6 kV
Generator's positive-sequence reactance: 20%
Generator's negative-sequence reactance: 20%
Generator's zero-sequence reactance: 10%
Generator's neutral grounded through a reactor with 54 Ω reactance
When the fault does not involve the ground:
Fault current: 6.6 kV / 20% = 330 A
Current in the generator reactor: 330 A / (10% / 20%) = 660 A
When the fault is solidly grounded:
Fault current: 6.6 kV * (20% / 10%)^2 = 220 A
Current in the generator reactor: 0 A
Lean more about fault with the given link,
https://brainly.com/question/3088
#SPJ11
Consider transmission of light (extinction coefficient = 1.96e-04 /m) through 0.5 km of air containing 0.5 µm fog droplets. The percentage transmission is:
The percentage transmission of light through 0.5 km of air containing 0.5 µm fog droplets is approximately 90.48%.
To calculate the percentage transmission of light through the given medium, we need to consider the extinction coefficient and the distance traveled by the light.
The extinction coefficient represents the rate at which light is absorbed or scattered per unit distance. In this case, the extinction coefficient is 1.96e-04 /m.
The distance traveled by the light through the medium is given as 0.5 km, which is equal to 500 meters.
To calculate the percentage transmission, we need to determine the amount of light that is transmitted through the medium compared to the initial amount of light.
The percentage transmission can be calculated using the formula:
Percentage Transmission = (Transmitted Light Intensity / Incident Light Intensity) * 100
The amount of transmitted light intensity can be calculated using the exponential decay formula:
Transmitted Light Intensity = Incident Light Intensity * e^(-extinction coefficient * distance)
Substituting the given values into the formula:
Transmitted Light Intensity = Incident Light Intensity * e^(-1.96e-04 /m * 500 m)
Now, we need to determine the incident light intensity. Since no specific value is provided, we'll assume it to be 100% or 1.
Transmitted Light Intensity = 1 * e^(-1.96e-04 /m * 500 m)
Calculating this value:
Transmitted Light Intensity ≈ 0.9048
Finally, we can calculate the percentage transmission:
Percentage Transmission = (0.9048 / 1) * 100 ≈ 90.48%
Therefore, the percentage transmission of light through 0.5 km of air containing 0.5 µm fog droplets is approximately 90.48%.
Visit here to learn more about extinction coefficient brainly.com/question/32634704
#SPJ11
1. Addition of two vectors. A = (200g, 30°)=173.205g ax +100g ay-4.33 cm ax +2.5cm ay +B=(200g, 120°)=-100g ax +173.205g ay=-2.5 cm ax +4.33 cm ay Resultant = A + B = ( _ grams, at angle °) °) Mathematical solution: Ax = Bx = Resultant in the x direction (Rx) = Resultant in the y direction (Ry) = Σ The magnitude of the Resultant = √R+R} R, arctan The angle of the resultant = R₂ Equilibrant = ( grams, at angle Ay = By = Ax +Bx = R₁₂ Ay +By =R,
To solve the problem, we'll break down the vectors A and B into their components and then add the corresponding components together.
A = (200g, 30°) = 173.205g ax + 100g ay - 4.33 cm ax + 2.5 cm ay
B = (200g, 120°) = -100g ax + 173.205g ay - 2.5 cm ax + 4.33 cm ay
Ax = 173.205g
Ay = 100g
Bx = -100g
By = 173.205g
Rx = Ax + Bx = 173.205g - 100g = 73.205g
Ry = Ay + By = 100g + 173.205g = 273.205g
R = Rx ax + Ry ay = 73.205g ax + 273.205g ay
|R| = √(Rx^2 + Ry^2) = √(73.205g)^2 + (273.205g)^2) = √(5351.620g^2 + 74735.121g^2) = √(80086.741g^2) = 282.9g
θ = arctan(Ry/Rx) = arctan(273.205g / 73.205g) = arctan(3.733) ≈ 75.79°
Therefore, the resultant vector R is approximately (282.9g, 75.79°).
Learn more about vectors here : brainly.com/question/30958460
#SPJ11
Which type of radiation is used to detect lava flows or oil deposits?
AO microwaves
BO visible CO X-rays
D. infrared
Infrared type of radiation is used to detect lava flows or oil deposits.
Thus, Infrared is the thermal radiation (or heat) from our globe that earth scientists investigate. Some of the energy from incident solar radiation that strikes Earth is absorbed by the atmosphere and the surface, warming the planet. infrared type of radiation is used to detect lava flows or oil deposits.
Infrared radiation, which is emitted by the Earth, is what causes this heat. This infrared radiation is detected by instruments on board Earth observation satellites, which then use the measurements obtained to examine changes in land and ocean surface temperatures.
On the surface of the Earth, there are other heat sources like lava flows and forest fires. Infrared data is used by the Moderate Resolution Spectroradiometer (MODIS) instrument onboard the Aqua and Terra satellites to track smoke and identify the origin of forest fires.
Thus, Infrared type of radiation is used to detect lava flows or oil deposits.
Learn more about Infrared radiation, refer to the link:
https://brainly.com/question/20779091
#SPJ4
The cross sections for the interaction of fast neutrons with the nuclide plutonium-241 are as follows: elastic scattering σel=5.17×10−28 m2, inelastic scattering σinel =1.05×10−28 m2, radiative capture σradcap =0.23×10−28 m2, fission σfission =1.63×10−28 m2. Each fission releases, on average, 3.1 fast neutrons. The density of plutonium-241 is 2.00×104 kg m−3. (i) With reference to the values quoted above, discuss why you would expect a pure sample of plutonium-241 to support an explosive fission chain reaction with fast neutrons. [4 marks] (ii) Calculate the mean distance between interactions of a fast neutron in a pure sample of plutonium-241. [4 marks] (iii) Estimate the minimum mass of a sphere of pure plutonium-241 required to sustain a fission chain reaction. [4 marks]
(i) A pure sample of plutonium-241 is expected to support an explosive fission chain reaction with fast neutrons due to its high fission cross-section, which indicates a high probability of fission events occurring when bombarded with fast neutrons.
(ii) The mean distance between interactions of a fast neutron in a pure sample of plutonium-241 can be calculated using the concept of mean free path and the cross-section values provided.
(iii) The minimum mass of a sphere of pure plutonium-241 required to sustain a fission chain reaction can be estimated based on the critical mass concept and the characteristics of plutonium-241.
(i) The high fission cross-section (σfission) indicates a high probability of fission events occurring, leading to a chain reaction.
(ii) The mean free path (λ) can be calculated using the formula:
λ = 1 / (Σtotal × N)
Where:
Σtotal = σel + σinel + σradcap + σfission
N = Avogadro's number = 6.022 × 10^23
Substituting the given values:
Σtotal = (5.17 + 1.05 + 0.23 + 1.63) × 10^(-28) m^2
N = 6.022 × 10^23
Calculate λ using the formula.
(iii) The critical mass (Mc) can be estimated using the formula:
Mc = ρ × Vc
Where:
ρ = density of plutonium-241
Vc = critical volume
To estimate Vc, we can assume a spherical shape and use the formula:
Vc = (4/3) × π × Rc^3
Where:
Rc = critical radius
The critical mass can be calculated by substituting the values into the formula.
(i) A pure sample of plutonium-241 supports an explosive fission chain reaction due to its high fission cross-section.
(ii) Calculate the mean distance between interactions of a fast neutron in a pure sample of plutonium-241 using the formula for mean free path.
(iii) Estimate the minimum mass of a sphere of pure plutonium-241 required to sustain a fission chain reaction using the concept of critical mass and the provided density value.
To learn more about fission click here.
brainly.com/question/27923750
#SPJ11
