There are many answers to this scenario. Please post yours and comment what you like about others and how you might improve them.

The Acme Company has two offices. They would like you to help them address their network. Like all companies, they want to account for growth, but want a simple, organized addressing scheme. They have been assigned the range of 201.11.10.224/29 for public access. Their VLAN needs are below for each site.

The 201.11.10.224/29 address has only 8 total addresses. That's not even going to cover the first subnet. This is a component of IPv4 and limited addresses. So, we can use Network Address Translation (NAT) on the router limiting the 201.11.10.0 addresses to the outside of network and use private addresses internally. What are the private address ranges? (Hint: They are in Module 11.3.1). Pick one and use that to address the scenario.

Document how you would address the network and communicate it to Acme leadership.

Walla Walla Office (HQ)

Management (10 devices)
Accounting (25 devices)
IT (30 devices)
Production (100 devices)
Seattle Office

Management (10 devices)
Accounting (25 devices)
IT (15 devices)
Production (50 devices)

Answers

Answer 1

Network address translation between Walla Walla and Seattle is the optimum network method for this.

What is Network Address Translation?

Network address translation is a technique for translating one IP address space to another by altering network address information in packet IP headers while they are in transit through a traffic routing device.

The NAT (network address translation) is originally established to limit the number of public IP addresses used by major corporate businesses or companies, hence preserving both IP address conservation and protection.

There are several devices within the community that need to be protected from the outside world, thus the NAT permits private IP addresses to connect to the outside world.

As an example, designating a public handle to a set of HOST/gadgets inside an inside community/corporation.

Remember that a host or device in an inner network with a private IP address, say (192.168.1.11), wishes to interact with an internet server on the internet ( outside world ). Now, NAT will convert this non-public IP address into a public IP address (for example, 1.12.1.1) that is known to everyone.

So, the web server recognizes this precise public IP and returns its outcome to this deal with (1.12.1.1), after which it routes to the vacation spot, where the NAT converts it once more to the private IP deal with and sends the outcomes to the desired device in the non-public network.  

As for a corporation's local network, there are numerous non-public IP with one public IP denoting all of them), so the result now, obtained via one of the devices in that network

Learn more about Network Address Translation:
https://brainly.com/question/13105976?
#SPJ1


Related Questions

One ounce is equal to 28.35 grams. Convert 16 ounces to grams. Round your answer to the nearest tenth.
O 1.8 grams
O 12.4 grams
O 44.4 grams
O 453.6 grams

Answers

Answer:

453.6 gm

Explanation:

28.35 g / oz  *  16 oz = 453.6 gm

technician a says that loose fan belts are usually destroyed more rapidly than belts that are adjusted too tight. technician b says that too tight adjustment on poly-v fan belts can destroy bearings. who is correct?

Answers

The bearings and shaft experience additional loads as a result of this increased tension. Bearings' lifespans might be shortened by excessive stress.

Explain about poly v belt?

The inside of the Poly-V Belt, also known as the Ribbed Belt, is lined with longitudinal v-shaped ribs. These ribs give the pulley and the belt a bigger surface area to contact, which increases friction force. Compared to a flat belt or rubber v-belt of the same size, the belt can convey more power as a result.

The Poly-V Belt's design ensures superior protection for all reinforcing cords, resulting in a more even load distribution. The Poly-V Belt also serves as a guide for a belt tensioner or idler pulley. Less space is needed for Poly-V Belt drives, and the Belt can be stretched under higher tension.

To learn more about Poly v belt refer to:

https://brainly.com/question/18368496

#SPJ4

Two forces are acting at an angle of 120. The bigger force is 40n and the resultant is perpendicular to the smaller one. The smaller force is

Answers

The smaller force is 20 Newtons.

Let, the magnitude of the smaller force be F Newton.

Now, the resultant force makes an angle of 90° with the smaller force. So, the angle between the resultant force and the larger force =

(120° - 90°) = 30°.

So, tan 30° = (F * sin 120°) / (40 + F * cos 120°)

(1 / √3) = {F * (√3) / 2} / {40 + F * (- 1 / 2)}

80 - F = 3F

4F = 80

F = 20.

So, the magnitude of the smaller force is 20 Newtons.

Learn more about force at:

https://brainly.com/question/25239010

_____ can process many pieces of data at the same time and learn to recognize patterns.

Answers

Neural networks can process many pieces of data at the same time and learn to recognize patterns.

However, similar to the brain, such networks are capable of processing a variety of information concurrently, learning to spot patterns, and programming themselves to address similar issues on their own. Single instruction multiple data, or SIMD, is a type of parallel processing where a computer has two or more processors that all follow the same instruction set but handle distinct types of data. Large data sets that are based on the same predefined benchmarks are frequently analyzed using SIMD. Haptic interfaces, which are frequently used in gaming consoles, clothes, and sports training equipment, give tactile feedback by imparting vibrations or pressures to the user using actuators that are embedded in the device (for example, a cell phone).

Learn more about network here-

https://brainly.com/question/13051988

#SPJ4

kalpakjian and schmid, problem 5.70. a 75-mm thick square plate and a right circular cylinder with a radius of 100 mm and height of 50 mm each have the same volume. if each is to be cast using a cylindrical riser, will each part require the same size riser to ensure proper feeding? explain.

Answers

Here, it is evident that a square plate requires more time than a cylinder. Therefore, a larger riser will be needed, and there will be a range of sizes for the riser.

We are aware that the time required for solidification equals C(volume/area), where C is a constant.

volume of cylinder = r2h where r = 100mm = 0.1 m and h = 50mm = 0.05 m

Cylinder volume = (0.1)

²×0.05 =0.00157m³

the cylinder's total surface area is equal to 2r² + 2rl (0.1)

Time taken for the cylinder = C(Volume/Area) = C(0.00157/0.0942) = (2.78 10⁻⁴)C since 2 + 2(0.1)(0.05) = 0.0942 m2.

For a square plate, h = 75 mm = 0.075m, l = b = x, and x = 0.144m. Accordingly, l = b = 0.144m, and the volume of the square plate is equal to 0.0157 m³ [A/C to inquiry].

Total surface area is equal to 2 (lb + bh + hl) (0.144)

Time taken for a square plate equals C(volume/area) = C(0.00157/0.0847) = (3.43 10⁻⁴)C because 2 + 4 (0.144) (0.075) = 0.0847 m³

Learn more about volume here-

https://brainly.com/question/22443936

#SPJ4

is it possible to create something that no one else has created before the near future

Answers

Answer:yes

Explanation:

That's what other people done they've created something no one else thought of.

air flows at 1.2 m/s along a flat surface when it encounters a jet of air issuing from the horizontal wall at point a, as in fio p8.16. the jet volume flow is 0.4 m/s per unit depth into the paper. if the jet is approximated as an inviscid line source, (a) locate the stagnation point s on the wall. (b) how far vertically will the jet flow extend into the stream?

Answers

In the upper atmosphere, jet streams are relatively narrow bands of powerful wind. Jet streams carry the winds as they go from west to east

Explain about the jet flow?

Jet streams can travel at speeds of more than 275 mph (239 kts / 442 km/h) and range in height from four to eight miles. Both the Northern and Southern Hemispheres have jet streams.

At altitudes of roughly 8 to 15 kilometres, jet streams move across the tropopause, the region between the troposphere and the stratosphere (5 to 9 miles). When cold air and hot air collide, strong air currents are created that, when viewed on a jet stream map, often resemble wavy, striated rivers.

The mid to upper troposphere, the part of the Earth's atmosphere where we live and breathe, is where jet streams are found, about five to nine miles above the planet's surface.

To learn more about jet flow refer to:

https://brainly.com/question/5993570

#SPJ4

An example of an external irreversibility associated with the Rankine cycle is

a. expansion of the working fluid through the turbine.

b. frictional effects resulting in pressure drops.

c. combustion of fuel.

d. irreversibilities in the pump.

Answers

An example of an external irreversibility associated with the Rankine cycle is combustion of fuel. Option C is correct.

What is the Rankine cycle?

The Rankine cycle is defined as a modified thermodynamic cycle that describes how certain heat engines, such as steam turbines or reciprocating steam engines, extract mechanical work from a fluid as it passes between a heat source and a heat sink.

The Rankine cycle, also known as the Rankine Vapor Cycle, is a process that is widely used in power plants such as coal-fired power plants and nuclear reactors. The best example of an external irreversibility associated with the Rankine cycle is combustion of fuel.

Therefore, option C is correct.

Learn more about the Rankine cycle, refer to:

https://brainly.com/question/16836203

#SPJ1

How many different welding processes are in use?

Answers

There are basically five types of welding namely:

a)Gas Metal Arc Welding (GMAW/MIG)

b)Friction welding,

c)ELECTRON BEAM WELDING

d) LASER BEAM WELDING

e) RESISTANCE WELDING

What is welding?

Welding is a fabrication process in which two or more parts are joined together using of heat, pressure, or both to form a joint as the parts cool. materials to be welded include metals, thermoplastics, and wood.

Types of welding processes

a)Gas Metal Arc Welding (GMAW/MIG)

Used mainly for joining metals like stainless steel, nickel, copper alloys, aluminum, titanium, and cobalt.

b)Friction welding

This is a  technique used to join materials using mechanical friction. this can be used to join wood, steel, and aluminum.

c)ELECTRON BEAM WELDING

This process uses a mean of high-velocity electrons to combine materials this can be used to join thick sections in the aerospace, automotive, rail, and nuclear power industry.

d)LASER BEAM WELDING

this is used to combine pieces of metal or thermoplastics.

e) RESISTANCE WELDING

This is a process that joins metals by applying pressure and passing a current through them for a period of time.

Learn more on welding from

https://brainly.com/question/21049525

#SPJ1

Which of the following best describes a fiscal policy tool?

a. government spending
b. financial capital markets
c. bank lending
d. household spending

Answers

The element or factor which best describes a fiscal policy tool is: a. government spending.

What is a fiscal policy?

A fiscal policy is sometimes referred to as monetary policy and it can be defined as the strategic use of government revenues and expenditures, in order to influence and control macroeconomic conditions such as:

Aggregate demand (AD)Money supplyEmployment within a country.Inflation

The types of fiscal policy.

Generally speaking, there are two (2) main types of fiscal (monetary) policy that are typically used across the world and these include the following:

Expansionary fiscal policy.Contractionary fiscal policy.

In conclusion, we can reasonably infer and logically deduce that government spending is an element which is used as a fiscal policy tool to influence and control macroeconomic conditions.

Read more on fiscal policy here: https://brainly.com/question/6583917

#SPJ1

Answer:

A) government spending is the correct answer

Explanation:

(econ 1101)

technician a says that proper starter operation depends on the battery being at a 95% charge and battery cables being of the correct size (gauge) and having no more than 0.8-volt drop. technician b says that voltage-drop testing includes cranking the engine, measuring the drop in voltage from the battery to the starter, and measuring the drop in voltage from the negative terminal of the battery to the engine block. who is right?

Answers

The right one is Technician b says that voltage-drop testing includes cranking the engine, measuring the drop in voltage from the battery to the starter, and measuring the drop in voltage from the negative terminal of the battery to the engine block .

What is a voltage drop test?To quickly identify high-resistance issues in a circuit, voltage drop testing is a straightforward but efficient diagnostic technique.You can measure the voltage drop across a load, device, or conductor using the DC voltage scale on your Digital Volt Ohm Meter (DVOM) or Digital Multi-meter.Utilizing a DMM to keep track of the voltage and amps being used by a specific circuit, group of circuits, component, or electrical system, voltage drop testing is carried out (windshield wipers, cruise control, charging system, etc.). The intended voltage or battery voltage is compared to the actual voltage next (if applicable).

To learn more about voltage drop test refer to:

https://brainly.com/question/27851005

#SPJ4

a fatigue test was conducted in which the mean stress was 60 mpa (8702 psi), and the stress amplitude was 230 mpa (33360 psi). (a) compute the maximum stress level. mpa (b) compute the minimum stress level. mpa (c) compute the stress ratio. (d) compute the magnitude of the stress range. mpa

Answers

The ratio of the least to highest stress is known as the stress ratio. 345 mpa is the greatest stress level.

Explain about the maximum stress level?

The mean stress is 60 mpa. The highest tensile stress and the minimum compressive stress, respectively, are denoted by the words "maximum stress" and "minimum stress." The stress range was established using the absolute difference between the highest and lowest stress.

Maximum stress level = 1/2 of the maximum and minimum stresses.

Then,

60 = 1/2 (Maximum stress minus Minimum stress)

230 = Maximum Stress plus Minimum Stress - (1)

As opposed to that,

Amplitude is= half of the maximum and minimum stresses.

120 = 1/2(Max. stress - Min. Stress) (Max. stress - Min. Stress)

460 equals Maximum Stress - Minimum Stress - (2)

Solving equations (1) and (2) yields:

Equation (1) + (2) 230 = Maximum stress + Minimum stress

460 = Maximum stress - Minimum stress

690 = 2 Maximum stress

690/2 = 345 mpa

To learn more about maximum stress level refer to:

https://brainly.com/question/13897375

#SPJ4

technician a says that rotors should be measured for thickness variation (parallelism). technician b says that rotors should be measured for lateral runout. who is correct?

Answers

Brake rotor micrometer. Parallelism is when the thickness of the rotor varies from point to point.

The parallelism of the brake disc allows the piston to move in and out of the caliper body when pressure is applied. The maximum allowable runout of the rotor friction surface is 0.002 inches (0.050 mm) as specified by most manufacturers.

Steering axle brake pad thickness must be a minimum of 3.2 mm (1⁄8 inch) for air disc brakes and a minimum of 1.6 mm (1⁄16 inch) for hydraulic disc, drum and electric brakes . Runout occurs due to eccentricity (processing error) and axial bending. Both cause uneven distribution of mass around the axis of rotation. Both create destructive forces, cause misalignment, and reduce machine life. Both problems can be serious,

Learn more about parallelism here-

https://brainly.com/question/20769806

#SPJ4

an automotive air conditioner produces a 2-kw cooling effect while consuming 0.75 kw of power. what is the rate at which heat is rejected from this air conditioner?

Answers

The rejected by the air conditioner system is 2.75 kilowatts.

An air conditioner system involves a refrigeration cycle. It uses power to get heat from the cold reservoir before sending it to the hot reservoir. The model is described by the First Law of Thermodynamics:

QL+W-QH=0

Where:

QL- Heat rate from the cold reservoir, measured in kilowatts.

QH = Heat rate liberated to the hot reservoir, measured in kilowatts.

W =  Power input, measured in kilowatts.

The heat rejected is now cleared:

QH=QL+W

If QL=2kW and W=0.75kW

QH=2.75kW

The rejected by the air conditioning system is 2.75 kilowatts.

Learn more about the rate of heat here: https://brainly.com/question/13411214

#SPJ4

a battery high rate discharge (load capacity) test is being performed on a 12 volt battery. technician a says that a good battery should have a voltage reading of higher than 9.6 volts while under load at the end of the 15-second test. technician b says that a battery conductance tester is often used to load the battery to two times the cca rating of the battery. who is right?

Answers

Technician A is correct.

What is CCA rating ?

The battery industry uses the CCA rating to describe a battery's capacity to start an engine in cold weather. A 12-volt battery's rating is the maximum amount of amps it can produce for 30 seconds at 0°F while maintaining a voltage of at least 7.2 volts.

What is Load capacity ?The highest force that may be delivered to a stage in a given direction while still satisfying stage requirements is known as the load capacity. This maximal force is made up of both static (gravity times mass) and dynamic (mass times acceleration) forces. Any outside forces operating on the stage, such vibrations, must be considered dynamic forces. The maximum accelerating force that a stage can produce without going over its load capacity determines how much acceleration it can give a mass.

Learn more about Rated load capacity refer :

https://brainly.com/question/28298750

#SPJ4

what is the thermal efficiency of a rankine cycle with isentropic compression and expansion for which steam leaves the boiler as saturated vapor at 6 mpa and is condensed at 50 kpa? how does this efficiency compare the theoretical carnot efficiency? hint: draw a thermodynamic sketch of the process and look online for useful steam tables.

Answers

The carbon footprint of a building is greatly decreased by a thermally efficient building shell. 30% is the thermal efficiency.

Explain about the thermal efficiency?

The proportion of heat energy that is converted into work is known as a heat engine's thermal efficiency. Even the most efficient heat engines have low efficiency; typically below 50% and frequently much lower. As a result, heat engines' energy loss to the environment represents a significant waste of energy resources.

When heat enters the boiler, the water goes through a sequence of state and energy changes before producing power through the turbine. This is known as a Rankine cycle.

We first determine the enthalpies for each state.

state 1

P = 6000 kpa x = 1 quality

h1=2784kJ/Kg

s1=5.889KJ/kgK

state 2

P=50kPa where entropy 1 Equals entropy 2

h2=2041kJ/Kg

state 3

P = 50 kpa x = 0 quality

h4=h3=340.5kJ/Kg

30% efficiency

To learn more about Thermal efficiency refer to:

https://brainly.com/question/24244642

#SPJ4

a bushing is to be manufactured from coarse iron powders. it is desired that it have a final density 90% that of cast iron, and it is known that the shrinkage in sintering will be approximately 5%. the bushing is 50 mm in outer diameter and has a 20 mm inner diameter, what is the required press force? hint: percent shrinkage is along a single dimension

Answers

Surface is not a factor in the pressing force. Thus, regardless of the press's load, the same force is always applied.

Explain about the press force?

A press is nothing more than a flat bed with a mechanically or hydraulically controlled pressing ram or rod. To produce a metal-pressed item, you must insert two halves of a metal press tool into the press. The tool is then bolted to the work surface at the bottom and to the ram or rod at the top

Presses are widely employed to bend or straighten materials as well as to press two items, such as bearings or other metal shaft-fitted components, together or away. Some smaller presses, like C-frame presses, can also be used to keep materials together during assembly or remove sections for maintenance.

To learn more about press force refer to:

https://brainly.com/question/21496864

#SPJ4

ase 8. while discussing the causes of a rich air-fuel ratio: technician a says that a rich air-fuel ratio may be caused by low fuel pump pressure. technician b says that a rich air-fuel ratio may be caused by a defective coolant temperature sensor. who is correct?

Answers

Answer:

technician

Explanation:

technician a says that the starter control circuit includes the ignition switch, neutral safety (clutch) switch, and solenoid. technician b says that the power circuit includes the battery, battery cables, solenoid, and starter motor. who is right?

Answers

Both technician A and technician B are right.

The starter control part contains the ignition switch, neutral safety switch, and solenoid. Meanwhile, the power circuit includes a power source to drive electrical current around the circuit (a battery) A conductor to carry the current around the circuit (some cable) A load that has resistance (a bulb, a heating element, a motor, etc.)

The starting system offers a step of rotating (cranking) the vehicle's internal combustion engine (ICE) to start the combustion cycle. The starting system includes the battery, cables, a solenoid, a starter motor, a ring gear, and an ignition switch.

Learn more about power circuits at https://brainly.com/question/2933971

#SPJ4

Consider the following expression BNF:

::= + | - |

::= * | / |

::= | ( )

::= 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9

Using recursive descent, and only recursive descent, scan expressions that adhere to this BNF

to build their expression tree; write an integer valued function that scans the tree to

evaluate the expression represented by the tree.

There are plenty of clever programs online that you can download to evaluate arithmetic

expression tree; if you want zero in this assignment, download one and submit it as

programming assignment #2; if you want a grade greater than zero, please follow our

instructions. Thanks.

Input:

• A numeric expression adhering to this BNF.

Output:

• Some representation of the expression tree.

• The result of evaluating the expression.

Answers

The program will be:

import java.io.IOException;

import java.util.Scanner;

/* This class represents a Node in Expression Tree that will contain a digit(symbol) and will have links to its

* left and right childs, which would be recursively having its own left and right sub childs accordingly

*/

class Node {

public char data; // Store Node Data

public Node leftChild; // pointer to left sub tree

public Node rightChild;// pointer to right sub tree

// Constructor to initialize Node with data

public Node(char x) {

data = x;

}

// display the Node's data stored

public void displayNode() {

System.out.print(data);

}

}

/* This is Stack class (Stack1) which performs push(), pop(), isEmpty() operation on Node's data */

class Stack1 {

private Node[] a; // Stack of type Node

private int top, m; // top = top of stack variable, m = Maximum Size of the Stack

public Stack1(int max) {

m = max;

a = new Node[m];

top = -1;

}

What is a have program?

Java is a popular object-oriented programming language and software platform that powers billions of devices such as notebook computers, mobile devices, gaming consoles, medical devices, and many more.

Java's rules and syntax are based on the C and C++ programming languages. The program is illustrated based on the information.

Learn more about program on:

https://brainly.com/question/26642771

#SPJ1

What is the overall meaning of the “Engineering V?

Answers

Answer:

Engineer V provides expert consultation in one or more areas for the design, development and implementation of technical products and systems. Resolves highly complex technical issues and conducts advanced research. Being an Engineer V recommends alterations to development and design to improve quality of products and/or procedures.

Explanation:

What type of drum system is mostly to be found on the rear of a modern front wheel drive vehicle ?

Answers

Drum Brakes are mostly to be found on the rear of a modern front wheel drive vehicle.

What Is Drum Brake?

Drum brakes have been around since 1900 ,patented until 1902 by Louis Renault.

A drum brake is a brake that , causes friction caused by a set of shoes or pads that press outward against a rotating cylinder-shaped part called a brake drum.It  rotates at the same speed as the wheel. The drum surrounds a set of brake shoes that are coated in materials that generate friction.

Types of drum brakes

Leading/Trailing Shoe type. Twin-leading shoeDuo Servo.

To know more about drum brakes from the given link

https://brainly.com/question/14210776

#SPJ13

which of the following is true for the depletion region capacitance of a pn junction? select one: a. all of these b. the capacitance depends on the square root of the reverse bias for an abrupt step junction c. the capacitance depends on the cube root of the reverse bias for a linearly graded junction d. the capacitance decreases as the reverse bias increases e. the amount of charge stored increases as the reverse bias increases

Answers

All of these statements are true.

The depletion region functions as an insulating or dielectric substance. P-n junction diodes can therefore be compared to parallel plate capacitors.

What is PN junction?A P-N junction is the boundary or interface between the p-type and n-type semiconductor material types inside of a semiconductor.The process of doping produces the P-N junction in a semiconductor.In an electrical circuit, a diode (PN junction) makes it easier for current to flow in one way than the other.While reverse biasing is applying a voltage across a diode in the opposite direction, forward biasing refers to applying a voltage across a diode that facilitates easy current passage. High resistance is present in the p-n junction diode's depletion zone.As a result, the depletion region functions as an insulating or dielectric substance.P-n junction diodes can therefore be compared to parallel plate capacitors.Transition capacitance is the measurement of how much capacitance changes as voltage increases.

To learn more about semiconductor  refer,

https://brainly.com/question/27753295?source=archive

#SPJ4

What is the definition of a rural area according to china and Europe?
An undeveloped country learns what from developed countries with regards to rural settlement and how do developers countries develop their areas? Which legislations can be implemented to achieve rural settlement planning?

Answers

The definition of a rural area according to China and Europe is: one in which more than half of the population resides in rural grid cells, as measured by the degree of urbanization.

What is a  rural area?

A rural area, sometimes known as the countryside, is a geographical area located outside of towns and cities.

Rural areas often have a low population density and tiny communities. Agricultural and forestry regions are sometimes referred to as rural.

Cities, suburbs, and towns are all examples of urban environments. Villages are sometimes referred to as rural places.

Cities have seen increased growth in terms of infrastructure and connectivity, such as airports, ports, railroads, housing, and roadways. Infrastructure development in rural regions is typically limited.

Learn more about rural areas:
https://brainly.com/question/13547914
#SPJ1

The program will take two integers from the user, say n1 and n2. It will then call the method sum(n1, n2) to calculate the sum of all numbers between n1 and n2, inclusive. The answer returned by the sum( ) method will then be displayed on the screen. For example, if the user enters 5 and 9, the program will print the value of 5+6+7+8+9. On the other hand, if the user enters 5 and -2, the program will print the value of 5+4+3+2+1+0+(-1)+(-2). Note: Do not assume the user will always enter the smaller number first.

Answers

The Java program will take two integers from the user and we are not assuming the user will always enter the smaller number first.

Step-by-step coding of the given problem:

import java.util.*;

class main{

public static void main(String args[])

{int n1,n2;

Scanner in=new Scanner(System.in);

System.out.print("Enter the starting number: ");

n1=in.nextInt();

System.out.print("Enter the ending number: ");

n2=in.nextInt();

System.out.println("The sum of the numbers from "+n1+" to "+n2+" is "+sum(n1,n2));

}

public static int sum(int n1, int n2)

{int i,sum=0,start,stop;

start=n2;

stop=n1;

if(n1<n2)

  {start=n1;

   stop=n2;

   }

for(i=start;i<=stop;i++)

    sum+=i;

return sum;

}

}

To learn more about Java Programming, visit: https://brainly.com/question/18554491

#SPJ9

Technician A says that a tapered roller bearing assembly has less rolling resistance than a similarly sized ball bearing assembly. Technician B says that the bearing assembly in a unitised wheel bearing assembly can normally be disassembled, cleaned, and repacked. Who is correct?

Answers

Technician A says that a tapered roller bearing assembly has less rolling resistance than a similarly sized ball bearing assembly. Technician B says that the bearing assembly in a unitized wheel bearing assembly can normally be disassembled, cleaned, and repacked. The technician that is correct is Technician B.

What is a Tapered Roller Bearing Assembly?

A cup and cone assembly is used in tapered roller bearings. The cup is made up of the outer ring, and the cone assembly is made up of the inner ring, rollers, and cage. This bearing design accommodates combined loads while maintaining minimal friction during operation.

A roller bearing is a cylindrical element that allows a bushing or bearing block to move with little friction.

A ball bearing is a spherical unit with the same purpose as a roller bearing. The real distinction is the contact surface between the bearing and the rail.

Learn more about tapered roller bearing assembly:
https://brainly.com/question/15313541

#SPJ1

the small-signal model is said to be valid for voltage variations of about 5 mv. to what percentage current change does this correspond? (consider both positive and negative signals.) what is the maximum allowable voltage signal (positive or negative

Answers

The signal is "high" when it is over the high threshold. Undefined intermediate levels lead to extremely implementation-specific circuit behavior.

It is customary to allow for some tolerance in the voltage levels utilized; for instance, logic 0 might be represented by 0 to 2 volts, and logic 1 by 3 to 5 volts. An example of a widely used signal standard is 0-10 volts, which states that a signal of 0 volts represents 0% of the measurement, a signal of 10 volts represents 100% of the measurement, a signal of 5 volts represents 50% of the measurement, and so on. For a "low" logic state and a "high" logic state, respectively, acceptable input signal voltages range from 0 volts to 0.8 volts and 2 volts to 5 volts. The supply voltage will, for the most part, determine the operating range.

Learn more about voltage here-

https://brainly.com/question/28632127

#SPJ4

Tyler is developing a robot that can be sent into war zones to ensure that any mines have been detonated before soldiers are sent into the area. The government is requiring a full scale model of this robot before it is willing to purchase one

Answers

The reason a prototype is necessary before committing to a purchase in this scenario is that the robot might be very expensive.

What is a prototype?

In Engineering, a prototype can be defined as a rudimentary (early) model, release, or sample of a particular product, so as to avail the developers and manufacturers an opportunity and ability to test a concept, functionality, or process within it.

This ultimately implies that, the main purpose of the prototype of a robot is to determine and show whether or not the robot and all of its features are in tandem with the design specifications and market requirements.

In this context, we can reasonably infer and logically deduce that the government requested for a full scale model of the robot before it would purchase one because it is most likely to be very expensive.

Read more on prototype here: https://brainly.com/question/7509258

#SPJ1

Complete Question:

Tyler is developing a robot that can be sent into war zones to ensure that any mines have been detonated before soldiers are sent into the area. The government is requiring a full-scale model of this robot before it is willing to purchase one.

What explains why a prototype is necessary before committing to a purchase in the following scenario?

part b - designing and analyzing a series rl low-pass filter using the available 130 h inductor, what is the value of the resistor needed to make a low-pass filter with a cutoff frequency of 18 hz ? express your answer to three significant figures and include appropriate units. g

Answers

When built, an RL circuit functions as a low pass filter. The resistor is the shunt component in the circuit, and the inductor is the series component.

The inductors' reaction to a rise in operating frequency is what causes the circuit's filtering operation. The frequency at which the output (load) voltage is equal to 70.7% of the input (source) voltage is known as the cutoff frequency for a low-pass filter. An audio signal processor called a low-pass filter (LPF) takes out undesired frequencies from a signal that are above a preset cutoff frequency. It allows the low-end to flow through, ideally unchanged, while gradually filtering out (attenuating) the high-end over the cutoff frequency.

Learn more about voltage here-

https://brainly.com/question/28632127

#SPJ4

if an aircraft is loaded 90 pounds over maximum certificated gross weight and fuel (avgas) is drained to bring the aircraft weight within limits, how much fuel should be drained?

Answers

When an aircraft is loaded 90 pounds or more than the maximum certificated gross weight and fuel (avgas) is drained to bring the aircraft weight within limits, 15 gallons of fuel should be drained.

How is aircraft loaded moment calculated?Determine the empty weight of the aircraft and the weights of passengers, luggage, and fuel by consulting the pilot's operating manual. To determine the moment, multiply each weight by the arm, which is the separation from the reference datum. To determine the gross weight, add up all the weights. To find the total moment, add all the moments together.n= L/W Where L is the lift produced by the wing and W is the aircraft's gross weight. As lift and weight are different types of forces, units cancel out when calculating the load factor, leaving the load factor dimensionless. However, because load factor refers to a force, it is expressed in units of G's.

To learn more about aircraft loaded moment refer to:

https://brainly.com/question/28250039

#SPJ4

Other Questions
10. In which of the following situations is a biotechnologist most likely to decide to use directed evolution as an enzyme engineering technique as opposed to rational design?A) When a structure of theenzyme is available to aid engineeringB) When the enzyme can only bescreened in a low throughput mannerC) When the enzyme mechanismis understood and provides insight to engineeringD) When current data allowsmolecular modelling techniques to be used predictivelyE)When none of the above are true What is the domain of the function y=2 x-6?O -O 0x Complete each sentence 1: The athlete was so agile that complete the sentence. 2: It was such a coincidence when complete the sentence. A construction company is planning the foundation for a house. Stakes have been placed in the ground to mark the corners of the foundation. The four sides formed are measured as 20 feet, 20 feet, 48 feet, and 48 feet. The diagonal of the quadrilateral formed is measured to be 54 feet. What type of triangle is formed by the diagonal and two sides of the current foundation plan? 2. Determine if the following function's widthwill be wider, narrower, or standard?y = 3(x + 5) + 11 Which of the following chemical reactions removes CO2 from the atmosphere? a. CH2O + O2 -> CO2 + H2O b. CH4 + O2 -> CO2 + H2O c. CO2 + H2O -> CH2O + O2 d. FeS2 + H2O -> FeO + H2S A concrete mixture contains 4 cubic yards of cement for every 20 cubic yards of grit. If a mason orders 50 cubic yards of cement, how much grit (in cubic yards) should he order if he is to use all of the cement? if you were told that you would get extra credit for finding a model showing chromosomes separating while sister chromatids were still attached, you would look for a model of according to studies on regional differences within the united states, which people are more likely to be introverts? how do we perceive different wavelengths of light? (hint: frequency is to pitch as wavelength is to ) ZABC is bisected by ray BD. m2 ABC = 80. What is mZ ABD?OA. 50OB. 40O C. 100OD. 75 Question 5 (5 points)Find the equation of the line passing through the point (-1, 5) and perpendicular tothe line y=-3x+4.A) 3y=-x+16B) 3y=x+16OC) y=-3x+8D) y=-3x+2OLD PLEASE HELP I WILL GIVE BRAINLIESTFind x and y*image is linked below* classical conditioning is based on . a. the consequences of making a response b. what happens before we respond c. punishments the organism receives d. the observation of another organism being reinforced for a response what is the tendency for individuals to not help someone in need if other people are around? multiple choice question. fundamental attribution error elaboration likelihood altruism bystander effect Deion plans to repaint some classroom bookcases. He has 3 5 /1 gallons of paint. All of the bookcases are the same size and each requires 1/5 gallon of paint. How many bookcases will he be able to paint? 4. How is a straight average different from a weighted average? if a company failed to make the end-of-period adjustment to move the amount of revenue that was earned from the unearned revenue account to the revenue account, this omission would cause: The decibel rules of thumb can be combined. (a) If a sound has intensity xdB, how many dB does a sound 100 times more intense have? (b) If another sound has intensity ydB, how many dB does a sound 4 times less intense have? (c) Combine what you know about (a) and (b): If a sound has intensity zdB, how many dB does a sound 25 times more intense have? The population of city A is 24% less than the population of city B, so city A's population is _____% of city B's.